Classic Exhibits VISIONARY DESIGNS VK-1201 User manual

www.classicexhibits.com
Step 1
Page 1 of 2
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - VK-1201 - General Layout
10’
10’
Plan View

www.classicexhibits.com
Step 2
Page 2 of 2
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 2
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - Backwall Assembly
Set upper horizontal bars
[51/5b] to be flush with
top of vertical extrusions.
Horizontal Placement
3a
5a
Stopper
Item
1
2
3
2a
3a
4a/4b
5a/5b
6/6a
Description
Base Plate
42”h Lower Square Vertical Extrusion
42”h Upper Square Vertical Extrusion
42”h Lower Square Vertical Extrusion w/ A10 Clamps Attached
42”h Upper Square Vertical Extrusion w/ A10 Clamps Attached
45”w Horizontal Extrusion
45”w Horizontal Extrusion
2.5”h Angle-Cut Vertical
Qty.
2
1
1
1
1
1/1
1/1
1/1
Steps:
1) Attach vertical extrusions [2] to base plates [1].
2) Attach upper vertical extrusions [3 and 3a] to lower extrusions [2 and 2a]
using connection bar [a].
3) Connect horizontal extrusions [4a to 4b and 5a to 5b] together using connection bars [b].
4) Attach horizontal assemblies [4a/4b and 5a/5b] between vertical assemblies as shown.
5) Attach angle-cut verticals to top of assembled backwall where indicated.
6) Apply graphic to back of assembled backwall.
7) Attach light to top of assembled backwall.
2a
3a
1
4a
1
2
3
5a
4b
5b
Connection
Bar
Slide Connection Bar
between Extrusions
and tighten Knobs
to secure.
Connection
Bar
Graphic Attachment
Apply graphic to back
of assembled backwall.
Connection
Bar
a
a
b
Connection
Bar b
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
**Do not over tighten Knobs.**
Knob
Knob
A10 clamps attached to vertical extrusions for Wing Attachment
6a 6
3
6Tighten setscrew
to secure
2.5” Vertical Attachment
Back View of Backwall
5b
Insert connect into
groove of extrusion [3].
Tighten setscrew
to secure.
Light Connection
Attach Lights to
Backwall where
desired and tighten
in place.
GREEN STAR indicates
location of connection
lock with knob.

www.classicexhibits.com
Step 2
Page 2 of 2
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea -
W
i
n
g
W
i
n
g
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Black Plastic
Set-screw
Wing Attachment
*Note: A10 clamps must
stay attached with verticals
Wing Attachment

www.classicexhibits.com
866.652.2100
© 2009
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Case Packing Instruction
(1) Backwall Components
Extrusions #3&3a
Extrusions #2&2a
Horizontal extrusions #4a&4b abd 5a&5b
Connection Bars A
Connection Bars B
Level 1 Level 3
Level 2
Wing Panels
Setup Hardware
Lights
Graphic