Classic Exhibits visionarydesigns VK-2957 User manual

www.classicexhibits.com
Step 1
Page 1 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Perspective View
Plan View 20’
10’
VK-2957 - General Layout

www.classicexhibits.com
Step 2
Page 2 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 3
Page 3 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
Graphic Removal
Graphic: To Ensure Proper Fit
Corner A
Corner D
Corner B
Corner C
It is important to first insert graphic
into each alternater corner then to
the sides of the frame.
If this is not done, graphic will not fit
into the frame correctly.
Step 1
Insert corner A.
Turn edge of graphic so silicon welt
is perpendicular to face of graphic.
Insert narrow side of welt with fabric
to outside into the channel.
Repeat for other side of this corner.
Step 2
Repeat Step 1 for opposite corner
C, then insert corner B, followed by
corner corner D, to complete the
installation of the corners.
Step 3
Once all corners are inserted, press
one silicon edge into channel from
corners and work toward the center.
Make sure welt is fully inserted into
channel. Continue until all sides are
done. Smooth out edges of graphic.
To remove the graphic from
the frame, locate the fabric
pull tab.
Gently pull up on the tab to
remove the fabric.
SEG Graphic Installation

www.classicexhibits.com
Step 1
Page 1 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2957 - Backwall Assembly
7
7A
7B
8
5
6
6B
8A
8B
6A 3
Item
2
3
5
6/6A
Qty.
1
1
1
1/1
Description
96”h Q914 Square Vertical Extrusion
96”h Q914 Square Vertical Extrusion
96”h Q914 Square Vertical Extrusion
96”h TSP46 Vertical Extrusion
Item
6B
7/7A
7B
8/8A
8B
23
Qty.
1
1/1
1
1/1
1
2
Description
92.417”h Z45 Vertical Extrusion
34”w TSP46 Horizontal Extrusion
68”w TSP46 Horizontal Extrusion
34”w TSP46 Horizontal Extrusion
68”w TSP46 Horizontal Extrusion
81.275”w Z45 Horizontal Extrusion
Steps:
1) Connect vertical extrusion [6] to vertical [5].
See Custom Cam Lock detail.
Repeat step for connecting verticals [3] & [6A].
2) Attach horizontal extrusions [23] between verticals [2] & [3].
NOTE: Velcro needs to face interior of setup.
3) Assemble horizontals [7], [7A] & [7B].
See TSP46 Connection detail.
Repeat step for horizontals [8], [8A], [8B].
4) Connect assembled horizontals between vertical assemblies
[5/6] & [3/6A]. See Corner Connections detail.
5) Attach vertical extrusion [6B] between assemblies
[7/7A/7B] & [8/8A/8B].
6) Apply fabric blocker to the velcro on [2/3/23].
7) Install SEG Fabric Graphic to [6/6A/7/7A/8/8A].
See SEG Graphic Installation Page in the General Information.
*
*
*
*
Top View Cam
Lock
Custom Cam Lock
*
TSP46
Screw clamps
cam lock into
groove of vertical
extrusion.
TSP46 Connection
*
PR53
*
*
*
*
*
Lock
Slide end of extrusion
over corner lock.
Tighten setscrew
to secure extrusions
Corner Connections
**
**
Velcro: Bottom
Edge
Velcro: Top
Edge
2
23
23
Velcro
S12
Extrusion
Profile
S12
Q914

www.classicexhibits.com
Step 2
Page 2 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2957 - Backwall Assembly Cont’d
3
5
12A
13
12
13A
4
24 25
27
25A
26
26A
2
9
9A
10
10A
1
Item
1
4
9/9A
10/10A
12/12A
13/13A
24
25/25A
26/26A
27
Qty.
1
1
1/1
1/1
1/1
1/1
1
1/1
1/1
1
Description
96”h Q914 Square Vertical Extrusion
96”h Q914 Square Vertical Extrusion
96”h TSP46 Vertical Extrusion
32”w TSP46 Horizontal Extrusion
16”h TSP46 Vertical Extrusion
29.244”w TSP46 Horizontal Extrusion
96”h Q914 Square Vertical Extrusion
96”h TSP49 Vertical Extrusion
32”w TSP49 Horizontal Extrusion
92.417’h Z45 Vertical Extrusion
Steps:
1) Assemble TSP46 extrusions [9,9A,10,10A].
See Corner Connections detail.
2) Connected assembled TSP frame [9/9A/10/10A]
between verticals [1] & [2].
See Custom Cam Lock detail.
3) Assemble TSP46 extrusions [12,12A,13,13A].
See Corner Connections detail.
4) Connect assembled TSP frame [12/12A/13/13A]
between verticals [3] & [4].
See Custom Cam Lock detail.
Steps Cont’d:
5) Assemble TSP49 extrusions [25,25A,26,26A]
See Corner Connections detail.
6) Connect assembled TSP49 frame [25/25A/26/26A]
between verticals [5] & [24].
See Custom Cam Lock detail.
7) Attach assembled door to vertical [3].
See Door Attachment detail.
8) Apply SEG Graphics to assembled TSP46 Frames.
See SEG Graphic Installation Page in the General Information.
NOTE: SEG Graphics apply to [9/9A/10/10A] & [12/12A/13/13A]
*
*
*
*
*
*
*
**
*
Top View Cam
Lock
Custom Cam Lock
*
TSP46
Screw clamps
cam lock into
groove of vertical
extrusion.
*
*
*
*
*
*
*
*
*
*
**
*
*
*
Lock
Slide end of extrusion
over corner lock.
Tighten setscrew
to secure extrusions
Corner Connections
Door Attachment
Pin
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin
as shown.
Door
Hinge
Hinge
*

www.classicexhibits.com
Step 3
Page 3 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2957 - Large D-Frame Light Box Assembly
14
18
18
15B
16
1717
15A
15C
15B 15
16
When assembled
Item
14
15/15A
15B/15C
16
17
18
Qty.
1
1/1
1/1
1
2
1
Description
96”h TSP70 Vertical Extrusion
42”w TSP70 Horizontal Extrusion
42”w TSP70 Horizontal Extrusion
150.79”h TSP70 Curved Extrusion
94.937”h Z45 Vertical Extrusion
94.937”h Z45 Vertical Extrusion w/ Holes
Steps:
1) Attach [15B] to [15] & [15C] to [15A].
2) Connect extrusion assmblies [15/15B] & [15A/15C] to vertical extrusion [14]
See TSP70 w/ A1 L-Bracket Connection detail.
3) Attach curved extrusion [16] to the ends of [15B] & [15C].
See TSP70 Connection detail.
4) Connect verticals [17] between horizontals assemblies [15/15B] & [15A/15B].
NOTE: must connect in back groove of TSP70.
5) Attach vertical [18] at connection point of extrusions [15B] & [16].
NOTE: See detail circle.
V4 Connector
TSP70
TSP70
Tighten
screw
Connect extrusions together
with V4 connector piece and
secure with set screws as shown.
TSP70 Connection
*
*
*
*
*
*
*
**Slide A1 L Bracket into TSP70
extrusion and secure with set screws.
A1
TSP70 w/ A1 L-Bracket Attachment
*
Tighten set
screw to secure
A1
A1
Tighten set
screw to secure

www.classicexhibits.com
Step 4
Page 4 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2957 - Small D-Frame Light Box Assembly
28
30
29A
29
When assembled
Item
28
29/29A
30
Qty.
1
1/1
1
Description
96”h TSP70 Vertical Extrusion
3”w TSP70 Horizontal Extrusion
150.7964”h TSP70 Curved Extrusion
Steps:
1) Attach [29] & [29A] to vertical extrusion [28].
See TSP70 w/ A1 L-Bracket Connection detail.
2) Attach curved extrusion [30] to the ends of [29] & [29A].
See TSP70 Connection detail.
V4 Connector
TSP70
TSP70
Tighten
screw
Connect extrusions together
with V4 connector piece and
secure with set screws as shown.
TSP70 Connection
*
*
*
**Slide A1 L Bracket into TSP70
extrusion and secure with set screws.
A1
TSP70 w/ A1 L-Bracket Attachment
*
*
*
Tighten set
screw to secure
A1
A1
Tighten set
screw to secure

www.classicexhibits.com
Step 5
Page 5 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2957 - Assembly of Assemblies
18
28
24
14
4
1
Steps:
1) Connect assembled Large D-Frame to assembled backwall by
using stand-off barrels & Caps.
NOTE: Extrusion [18] will attach to extrusion [4].
See Vertical Extrusion to Post Attachment detail.
Extrusion [14] will attach to extrusion [1].
See TSP70 to Vertical Attachment detail.
Steps:
2) Connect assembled Small D-Frame to assembled backwall by
using stand-off caps.
See TSP70 to Vertical Attachment detail.
3) Apply SEG graphics to D-Frame Light Box.
See SEG Graphic Installation page in General Information
V4
Vertical Extrusion to Post Attachment
*
Screw
Cap
Stand-off
*
*
*
*
*
*
*
*
V20 Connector
Slide V20 connector into groove of vertical extrusion.
Insert threaded Screw Cap through hole in TSP70
extrusion & into threaded hole of V20 connector.
Twist to secure in place.
TSP70 to Vertical Attachment
*
Screw
Cap
*
*
*
*

www.classicexhibits.com
Step 6
Page 6 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2957 - Wire Management
*
*
Wire Connection Point
Wire Connection Point
Power Cord for Monitor
Steps:
1) Connect power cords and DC adaptor cords to LED Tape Lighting.
See LED Tape Lighting Photos & Details detail.
2) Attach monitor mount stand-off barrels to vertical extrusions [17].
NOTE: Screw stand-off barrels into threaded holes of vertical extrusions.
3) Apply SEG fabric graphics to D-Frames and alcove.
See SEG Graphic Installation Page of General Information Pages.
2) Attach monitor mounts to vertical extrusions [17] and [27].
See Monitor Mount Attachment details for Small & Large Monitors.
Super Bright
Normal Bright DC Adapter Cord
Transformer
Connect LED Tape together where
extrusions meet. Attach DC adaptor
and plug into power source.
LED Tape Lighting Photos & Details
*
**
*
*
*
*
*
*
Symbol Key
Cord Flow Indicators
Power Strip Plugs
Number of Plugs
Cord Prong Plug End
PR53 Wire Management
Power Cords
(x3)
Wire Connection Points
Transformer will plug into
power strip with Small
Monitor and iPad kiosk.
Power Cord from
Small D-Frame
Transformer
Cords for Monitor & iPad
Transformer
(x3)

www.classicexhibits.com
Step 7
Page 7 of 7
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2957 - Pedestal Assembly
Lock
Infill
20
21
22
19
When assembled
Foam Lining
Removed
Home Button Shield
Optional Cover for Home Button
1) Remove foam lining from inside bottom of
clam shell as shown.
2) Attach Home Button Shield with double-sided
tape to inside of clam shell, keeping top of
shield flush with clam shell opening as shown.
NOTE: This is a permanent fix and can’t be easily
removed.
Wire
Access
iPad
Lock
Lock
Steps:
1) Slide infill between stand verticals as shown.
2) Attach horizontal [20] between stand verticals.
3) Attach base [19] to stand verticals using bolts.
4) Attach square plate [21] to stand using bolt.
5) Attach clam shell [22] to square plate [21] using hex nuts.
6) Insert iPad and feed wire through hole.
7) Attach pamphlet trays to stand. Refer to detail.
Clam Shell
Stand
Base
Plate
Square
Plate
Hex
Nuts
Tools Required:
1) Hex Tool
2) Pliers
Item
19
20
21
22
Qty.
1
1
1
1
Description
Base Plate
10”w Z72 Horizontal Extrusion
Mounting Plate
iPad Clamshell
Wire Management for iPad
Feed iPad charging cord through holes from top
to bottom of post as shown.