Classic Exhibits visionary DESIGNS VK-1950 User manual

www.classicexhibits.com
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1950 - Lightbox Assembly
Steps:
1) Attach lower vertical extrusions [2,3] to base plates [1] using screws.
2) Attach upper vertical extrusions [2a,3a] to lower vertical extrusions [2,3] as shown in detail.
3) Connect curved horizontals [4,4a,5,5a] together as shown.
4) Attach horizontal assemblies between vertical assemblies [2/2a,3/3a] as shown.
5) Apply blocker fabric to velcro on outside of horizontals [5/5a) and verticals.
6) Attach SuperNova light to verticals [2/2a,3/3a] and horizontals [5,5a] as shown,
connecting connectors together.
7) Attach SEG graphics to front SEG groove according to detail below.
8) Attach wings to A-10 clamps as shown.
Item Qty Description
1 2 Base Plate
2/2a 1/1 45” Half Round Vertical Extrusion
3/3a 1/1 45” Half Round Vertical Extrusion
4/4a 2/2 44.5041” Z45 Horizontal Extrusion
5/5a 2/2 46.6892” Z45 Curved Horizontal Extrusion
Velcro:
Outside/Bottom Edge
Velcro:
Back
Outside
Edge
Velcro:
Outside/Top Edge
**Note: the opening
of SEG extrusions must
be positioned outward
from the light box.
1
1
2
2a
3
3a
4
4
4a
4a
5
5
5a
5a
*
*
*Screws
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
Graphic: To Ensure Proper Fit
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
SuperNova Lights:
Attach to inside of verticals [2/2a,3/3a]
and top of curved horizontals [5]
Velcro:
Back
Outside
Edge
SuperNova Lights:
Attach to inside of verticals [2/2a,3/3a]
and bottom of curved horizontals [5a]
Tighten set screw to
secure A10 to extrusion.
A10 Clamp Detail
Tighten knob to secure
header/wing in place.

www.classicexhibits.com
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Case Packing - 1 of 1
5a,5a,5,5,4a,4a,4,4 2
Connectors
Wings
Baseplates
2a 3 3a
Setup Hardware
Graphics
Top View of Each Level
Level 1 Level 2 Level 3