Classic Exhibits visionary Magellan Miracle VK-2094 User manual

www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2094 - Magellan Miracle - General Layout
20’
10’
Plan View

www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C EliateDDliateDDetail B
Detail A
Setscrews

www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
1
2
3
4
5
6
7
8
9b
10a
11
12
Part Number
1
2
3
4
5
6
7
8
9a/9b
10a/10b
11
12
Qty
1
1
1
1
1
1
1
1
1/1
1/1
1
1
Description
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
23”w Horizontal Extrusion
23”w Horizontal Extrusion
44”w Horizontal Extrusion
44”w Horizontal Extrusion
Backwall Support Leg Extrusion
Backwall Support Leg Extrusion
Steps
1) Connect backwall upper and lower verticals together [1 to 2, 3 to 4 and 5 to 6].
2) Connect horizontal extrusions together [9a to 9b and 10a to 10b].
3) Attach horizontal assemblies [7and 8] between vertical assemblies [1/2 and 3/4].
4) Attach horizontal extrusions [9a/9b and 10a/10b] between vertical assemblies
[3/4 and 5/6].
5) Attach support leg extrusions [11 and 12] to back of verticals [1 and 5], see
leg attachment detail.
6) Attach monitor mount to upper vertical [4].
10b
Backside of backwall
Graphic Attachment
Apply graphics to back
of assembled backwall.
4
Monitor Mount
Monitor Mount Attachment
Light Connection
Attach Lights to
Backwall where
desired and tighten
in place.
Connect support leg
to vertical by placing lock
into slot and tighten with tool.
Support Leg Attachment
9a

www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
5
6
13
14
15
16
17a
18a
19
20
12
21
Part Number
13
14
15
16
17a/17b
18a/18b
19
20
21
Qty
1
1
1
1
1/1
1/1
1
1
1
Description
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
48.5”h Lower Curved Extrusion
48.5”h Upper Curved Extrusion
44”w Horizontal Extrusion
44”w Horizontal Extrusion
23”w Horizontal Extrusion
23”w Horizontal Extrusion
Backwall Support Leg Extrusion
Steps
1) Connect backwall upper and lower verticals together [13 to 14 and 15 to 16].
2) Connect horizontal extrusions together [17a to 17b and 18a to 18b].
3) Attach horizontal assemblies [17a/17b and 18a/18b] between vertical
assemblies [5/6 and 13/14].
4) Attach horizontal extrusions [19 and 20] between vertical assemblies
[13/14 and 15/16].
5) Attach support leg extrusions [21] to back of verticals [15], see
leg attachment detail.
6) Attach monitor mount to upper vertical [14].
17b
18b
Backside of backwall
Graphic Attachment
Apply graphics to back
of assembled backwall.
14
Monitor Mount
Monitor Mount Attachment
Light Connection
Attach Lights to
Backwall where
desired and tighten
in place.
Connect support leg
to vertical by placing lock
into slot and tighten with tool.
Support Leg Attachment
Backwall Assembly (Cont’d)

www.classicexhibits.com
Step 3
Page 3 of 4
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Workstation Assembly
Part Number
22
23
23a
24
25
Qty
2
2
2
2
2
Description
Base Plate
37.6”h Curved Vertical Extruaion
Oval Flange Plate
18.5”w Horizontal Extrusion
15.69”w Horizontal Extrusion
Steps
1) Attach curved vertical [23] to base plate [22],
see Base Plate Attachment detail.
2) Attach horizontal extrusions [24 and 25] between
curved verticals [23] and backwall verticals [3 and 13]
where indicated.
3) Attach flange plate to top of verticals [23] as shown.
4) Place counter tops on assembled counter base,
see Counter Attachment detail.
Base Plate Attachment
22
23
24
25
Connect Vertical Extrusion to Base
Plate by placing lock into slot
and tighten with tool.
23a
Screw
Counter Top Attachment
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
22
23
24
25
23a
Screw

www.classicexhibits.com
Step 4
Page 4 of 4
866.652.2100
© 2008
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Pedestal Assembly - QTY. 2
Part Number
26
27
28
29
30
31
Qty
1
1
1
1
6
2
Description
37.5”h Vertical Extrusion
37.5”h Corner Extrusion
37.5”h Corner Extrusion
37.5”h Vertical Extrusion
11”w Horizontal Extrusion
24.875”w Horizontal Extrusion
Steps
1)
Attach horizontal extrusions [30] between vertical
extrusions [26&27 and 28&29], see Top View for
extrusion orientation.
2) Attach curved horizontal extrusions [31] between
corner extrusions [27 and 28], placing insert between
curved horizontals.
Sintra Insert
26
27 28
29
31
31
30
Top View
26
27 28
29
31
30 30
Hook
*
*
**
*
*
*
Hook Attachment
Place hooks onto groove
of extrusions where indicated.
Then set shelf atop hooks.
Shelf
Steps (Cont’d):
3) Place hooks onto horizontal extrusions
where indicated, see Hook Attachment detial.
4) Set shelf atop hooks.
5) Set counter top atop assembled base.
Counter
30
30
30
30
30