Classic Exhibits Perfect 10 Bella User manual

www.classicexhibits.com
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - p10 -
Page 1 of 3
Step 1
Bella - General Layout
Plan View
10’
10’

www.classicexhibits.com
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - p10 -
Page 1 of 3
Step 1
Bella - Backwall Assembly
Part Number
1
2
3A
3
4
Step 1:
NOTE: Can be assembled either face down on floor then lifted
upright or upright as shown in drawings.
A) Connect vertical leg assemblies [1 and 2] together by connecting horizontal extrusions
[4] between assemblies tightening BLACK knobs on backside of extrusion making sure Velcro
faces toward BACK and placing it about one inch up from bottom and tightening.
B) Connect vertical extrusions [3 and 3A] to leg assemblies [1 and 2] using vertical connection
bar as shown.
C) Connect upper horizontal extrusion [4] between verticals [3 and 3A] placing it about one
inch down from top.
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully
engage, gently rock lock and extrusion while turning knob until lock fully opens.
Description
Left Leg Assembly w/ A10 Clamps Attached
Middle Leg Assembly
Upper Curved Vertical w/ A10 Clamps Attached
Upper Curved Vertical
23”w Horizontal
12
3A 3
4
4
Black
Knob
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
Vertical
Connection Bar
NOTE:When assembling horizontals they should
be placed approximately one inch from TOP and BOTTOM.
Slide
horizontal into groove
Assure
that a good
connection is made
and tighten to secure.
Slide Connection Bar into lower
leg assembly. Slide upper vertical
over bar and secure both.
Rear View of Display
Step 1
Step stool may be required
for assembly.

www.classicexhibits.com
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - p10 -
Page 2 of 3
Step 2
Bella - Backwall Assembly
Step 2:
NOTE: Can be assembled either face down on floor then lifted
upright or upright as shown in drawings.
A) Connect vertical extrusion [6] to leg assembly [5] using vertical connection bar as shown.
B) Connect horizontal extrusions [7 and 8] between vertical assemblies by tightening
BLACK knobs on backside of extrusion making sure Velcro faces toward BACK.
NOTE: Make sure the lock is flush with extrusion before tightening. If lock will not fully
engage, gently rock lock and extrusion while turning knob until lock fully opens.
12
3A 3
4
4
Black
Knob
Turn Knob Clockwise
to Tighten Lock
STAR indicates location of
knobs on BACKSIDE of unit.
Hinge Extrusion
Top Horizontal Hinge faces down.
Bottom Horizontal Hinge faces up.
NOTE:When assembling horizontals they should
be placed approximately one inch from TOP and BOTTOM.
Slide
horizontal into groove
Assure
that a good
connection is made
and tighten to secure.
5
6
7
8
Slide Connection Bar into lower
leg assembly. Slide upper vertical
over bar and secure both.
Rear View of Display
Step 2
Part Number
5
6
7
8
Description
Right Leg Assembly w/ A10 Clamps Attached
Upper Curved Vertical
69”w Horizontal w/ Hinge Facing UP
69”w Horizontal w/ Hinge Facing DOWN

www.classicexhibits.com
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - p10 -
Page 3 of 3
Step 3
Bella - Light, Cubby and Shelf Placement
Light Connection
Attach Lights to
Backwall where
desired and tighten
in place.
Shelf attaches to section
5 by setting atop pins
located on right side
and securing into place
with thumbscrew on left.
Cubby Attachment
Slide onto back pin first.
When attaching counter you will need to first
slide shelf onto back pin then set down on front
pin.
Accessary Attachment
Pins
Thumbscrew
Shelf attaches to back of
sections 1 and 2 by setting
atop pins located on back left
side.

www.classicexhibits.com
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - p10 - Case Packing - Case 1 of 2
Level 1
Level 2
Level 3
Level 4
Top View of each Level
Case #1 - Backwall Components
Leg Assembly
1
Leg Assembly
3
Leg Assembly
2
Vertical Connection Bar
Vertical Connection Bar
Vertical Connection Bar
Horizontal Extrusions #6
Horizontal Extrusion 5
Horizontal Extrusion 5

www.classicexhibits.com
866.652.2100
© 2008
WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - p10 -
Level 1
Level 2
Top View of each Level
Case #2 - Backwall Components
Backside
Shelf
Cubby
Wings
Case Packing - Case 2 of 2