CLEAR DESIGN THREE60 User manual

THREE60
CONFERENCE TABLE
Section: S1 | S2 | S3
General Installation Guide

TABLE OF CONTENTS
SECTIONS
S1 :: Sitting Height...................................................................1
S2 :: Standing Height .............................................................9
S3 :: Optional Power ............................................................ 15

S1: SITTING HEIGHT
OVERVIEW
THREE60 Conference Table
Quantities are for a 48” x 216” table, parts may
vary depending on project, but install steps will
remain the same.
1

2
SITTING HEIGHT
PARTS LIST
CODE QTY DESCRIPTION
GCNAB 2Angled Sleigh Leg
CNS48144
1Trapezoid Surface
2In-Surface Grommet
CNCGB
2Center Grommet Spacers
2In-Surface Grommet
CNCBV2 4Cabinet Base
BFB1 6Flat Bracket
GCNABCOV* 4Covered Leg
*If applicable.

3
SITTING HEIGHT
1 | PREPARE SURFACE AND MEASURE FOR LEGS
Carefully place surface upside-down on floor, a cushioned area is preferred.
Measure 12” from surface edge and center-align to determine leg placement.
NOTE: Same process for square-ended table.
2 | SECURE ANGLED SLEIGH LEGS
Follow measurements and insert screws per leg through the metal plate and into
the laminate surface.
12”

4
SITTING HEIGHT
3 | MEASURE FOR CABINET BASE OR COVERED LEG
Place cabinet base, or covered leg, centered under the table grommet cutouts.
5.91"
9.45"
9.45"
5.12"

5
SITTING HEIGHT
4 | INSTALL CABINET BASE OR COVERED LEG
Insert 4 screws per base through the laminate top into the bottom of the surface.
5 | ATTACH HARDWARE TO SURFACE EDGE
Insert 2 wooden dowels, attach 2 flat brackets, and connect 4 sets of joint
fasteners to one side of each surface edge.
Surface Edge

6
SITTING HEIGHT
6 | FLIP AND ASSEMBLE
Flip each piece over so that it is standing on a leg/cabinet base. Align the open
holes on the surface edge with the wooden dowels and the threaded rods on the
other surface edge.
7 | FULLY SECURE HARDWARE
Turn to Tighten
Hold Still
1. Set Hardware
2. Tighten Hardware

7
SITTING HEIGHT
8 | INSTALL GROMMETS
Insert wire management grommet.

8
END OF SITTING HEIGHT

S2: STANDING HEIGHT
OVERVIEW
THREE60 Conference Table
All parts listed are for a single standing height
table; additional parts will be needed for additional
standing height table.
9

10
STANDING HEIGHT
CODE QTY DESCRIPTION
GCNABSH 2Standing Height Angled
Sleigh Leg
CNS4896
1Main Surface
1In-Surface Grommet
GCNABSHLE 2Support Brace
BFB1 2Flat Brackets
PARTS LIST

11
STANDING HEIGHT
1 | PREPARE SURFACE
Carefully place surface upside-down on floor, a cushioned area is preferred.
Measure 12” from surface edge and center-align to determine leg placement.
Attach 2 flat brackets on the center seam of the table.
NOTE: Leg placement may need to be adjusted based on surface size.
2 | INSTALL ANGLED SLEIGH LEGS
Follow measurements and insert 15 screws per leg through the metal plate
and into the laminate surface.
12”

12
STANDING HEIGHT
3 | INSTALL SUPPORT BRACE
4 | FLIP AND INSERT GROMMET
Insert wire management grommet.
Note: See page 13 for optional covered sleigh leg. See page 15 for power
module install.

13
STANDING HEIGHT
OPTIONAL COVERED SLEIGH LEG
All steps for installation are the same. However, leg will be aligned with
the grommet cutout on the table.
NOTE: Covered sleigh leg is optional for wire management.
9.45"
5.12"

14
END OF STANDING HEIGHT

S3: OPTIONAL POWER
OVERVIEW
THREE60 Conference Table
15

16
OPTIONAL POWER
CODE QTY DESCRIPTION
BPCONF2V2
or BPCONF3 1In-Surface Power Module
JC1 5J-Clips
VB24 1Cable Vertebrae
PARTS LIST

17
OPTIONAL POWER
1 | ATTACH METAL CLIPS AND INSERT INTO SURFACE
Attach 2 metal clips to the back of the module base then insert into the pre-cut
holes in the surface.