CLEAR DESIGN BL-7 User manual

Includes Add-ons A1 | A4 | A5 | A6 | A7 | A8 | A9
BLADE L-SHAPE
STORAGE SUPPORTED
B L–7
*General Guide | See Master Plan

BLLBFV2 – Low Box/File Lateral .......................................................... 1
BLLOSV2 – Low Open Shelf Lateral ..................................................... 1
Merging Laterals ......................................................................................... 1
B L–7 – BLADE L-Shape - Storage Supported.................................... 1
Add-Ons
A1 – BLADE Cable Tray (Surface Mounted)...................................... 4
A4 – Modesty Panel .................................................................................. 7
A5 – Laminate Inset End Panels............................................................ 9
A6 – Laminate Surface-Height End Panels.......................................11
A7 – Laminate Divider-Height End Panels ........................................11
A8 – Steel Inset End Panels...................................................................13
A9 – Transaction Counter ......................................................................15
EDITION CODE
FACING
BLADE

LOW OPEN SHELF LATERAL
PARTS LIST
ITEM
CODE QTY PRODUCT CODE
1Top Panel (not needed)
1Bottom Panel
1Fixed Shelf Panel
2End Panels
1Back Panel
LSF 4Corner Foot
1

Requires 4 Wooden Dowels, 4 cam locks and 4 cam pins.
2 |INSERT HARDWARE INTO END PANELS
1 |SCREW CAM PINS INTO BOTTOM PANEL
Requires 6 cam pins.
LOW BOX/FILE LATERAL
Cam Pin
Cam Pin
Cam Lock Wooden Dowel
2

3 |INSERT HARDWARE INTO BACK PANEL
Requires 2 cam pins and 8 cam locks
4 |INSERT CAM LOCKS INTO FIXED SHELF
Requires 6 cam locks.
LOW BOX/FILE LATERAL
Cam Pin
Cam Lock
Cam Lock
3

Align the cam pins so that they sit inside of open cam locks. Use a
screwdriver to turn cam locks clockwise and lock into place.
6 |SECURE END PANELS
5 |SECURE FIXED SHELF TO BACK PANEL
Align the cam pins so that they sit inside of open cam locks. Use a
screwdriver to turn cam locks clockwise and lock into place.
LOW BOX/FILE LATERAL
4

7 |SECURE BOTTOM PANEL
Align the cam pins so that they sit inside of open cam locks. Use a
screwdriver to turn cam locks clockwise and lock into place.
8 |INSERT CAM LOCKS INTO FIXED SHELF
LOW BOX/FILE LATERAL
Secure foot to each corner using 4 wood screws.
DO NOT Install Top Panel 5

LOW BOX/FILE LATERAL
PARTS LIST
ITEM
CODE QTY PRODUCT CODE
BLLBFV2 1Low Box/File Lateral
LSF 4Corner Foot
2Handles
GBLLT2 1Laminate Merging Top
1 |SECURE FEET TO STORAGE AND FLIP
Flip storage piece so it is laying on its back; secure foot to each
corner using 4 wood screws.
6

2 |ATTACH HANDLES AND REMOVE DRAWERS
3 |REMOVE STORAGE TOP
Using 2 bolts each, attach handles to front of drawers. Once
secure, remove drawers from storage piece.
Locate the 6 cam locks across top edge on the inside of the
storage piece. Then, use a screwdriver to turn cam locks
counterclockwise to unlock. Carefully lift top from storage.
LOW BOX/FILE LATERAL
7

Set storage side-by-side then align top panel so it is flush with
sides, back and front of storage. Use wood screws to secure corner
brackets to inside of storage. Insert drawers.
5 |ATTACH TOP TO STORAGE
4 |CONNECT BRACKETS TO TOP PANEL
Attach 12 corner brackets to top panel using wood screws in the
places shown below.
COMBINE LATERAL
8

BLADE U-SHAPE B L–7
PARTS LIST
ITEM
CODE QTY PRODUCT CODE
BL24/BL30 1BLADE Leg
BASB72 1Support Bar
Laminate Surface
1Laminate Storage
BLSS 1Surface Stand Kit (set of 2)
9

1 |SECURE LEG TO SURFACE
Place assembled laminate storage into final position.
Secure the BL24/BL30 leg to the surface. Insert wood screws
through the leg bracket and into the underside of the surface.
2 |CONNECT STAND TO BRACKET, APPLY TAPE
Measure, cut and place tape on the bottom of the surface stands,
leave paper backing on the side facing out. Using 2 flat head bolts,
connect the surface stands to the mounting bracket.
STORAGE SUPPORTED SURFACE
BLADE
10

Align bracket with the edge of the outside of the surface then
measure 1 1/
4”between the mounting bracket and front/back of the
surface. Insert 4 wood screws per surface stand.
3 |ALIGN AND ATTACH BRACKETS TO SURFACE
4 |FLIP AND ALIGN BRACKETS
Flip surface assembly upright, place stands on laminate storage
and align as desired.
Once aligned, lift surface upward and off of storage piece. Remove
paper backing from double-sided tape and lower surface back
down to allow tape to stick to top of storage unit.
STORAGE SUPPORTED SURFACE
BLADE
1 1/
4”
11

7 |DETACH BRACKET FROM STAND TO SECURE
Remove bolts holding the stand and bracket together and carefully
lift the surface assembly away from the mounting brackets.
Mounting brackets should remain on the surface. Use
1/
2” long
wood screws to secure bracket.
8 |PLACE STAND ONTO BRACKET AND SECURE
Check and tighten any bolts and pieces to finish.
STORAGE SUPPORTED SURFACE
BLADE
12

IF WORKSTATIONS HAVE POWER, REFER TO BL-8 BLADE POWER
GUIDE
BLADE CABLE TRAY BL–7 | A1
PARTS LIST
QTY PRODUCT CODE
1BCTSM (set of 2)
1BNTEC *if applicable
13

CABLE TR AY
BLADE
Align slots on the cable tray and secure with two bolts from the
bottom. These hangers will mount to workstation surface. Insert
Beam Grommet Covers.
*NOTE: End Caps (BNTEC) are optional. Follow the same install
process with or without end caps.
Adjust BLADE cable tray to approximate width of surface. Insert
the screw through the overlapping beam slots and into the black
plastic piece. Slightly tighten the screw with only a few turns. DO
NOT fully tighten.
1 |ATTACH TRAY HANGERS AND END CAPS*
2 |INSERT BEAM LOCK
14

CABLE TR AY
OPTIONAL
3 | SURFACE MOUNT CABLE TRAY
Align cable tray flush to the edge of the surface (on 24" or 30"
surfaces). Insert wood screws through the hangers and into the
underside of the surface.
Tighten beam lock.
NOTE: Position may be affected if modesty panel is being installed.
Align Flush
IF WORKSTATIONS HAVE POWER, REFER TO BL-8 BL ADE POWER
GUIDE
15

MODESTY PANEL BL–7 | A4
PARTS LIST
QTY PRODUCT CODE
1
Brackets (set of 2)
• Steel - Included in Box
• Laminate - BMPBFB
1BMP##/GLMP##
* Process is the same for steel and laminate
16

1 |SECURE BRACKET TO MODESTY PANEL
Using 4 machine screws, secure brackets to the back of the steel
modesty panel.
Using 4 wood screws, secure brackets to the back of the laminate
modesty panel.
NOTE: Holes are not pre-drilled on laminate panels.
MODESTY PANEL
OPTIONAL
2 |ATTACH MODESTY PANEL TO WORKSTATION
Center the panel in reference to the width of the surface and screw
modestly panel directly to the bottom of your surface with wood
screws.
NOTE: Bracket may pass under the grommet, in this case, use
wood screws at the end of the bracket.
17

END PANELS BL–7 | A5
PARTS LIST
QTY PRODUCT CODE
4LEPBL1
1GBEP##
* Quantities are for one panel
18