Clearaudio Innovation Compact User manual

User manual
© clearaudio electronic GmbH, 2022-11 Made in Germany
Innovation Compact
Innovation Compact Black
Picture: Package with
Clearaudio tonearm „Magnify“
und Clearaudio cartridge
„Stradivari V2 MC“.
Innovation Basic Wood
Picture: Package with
Clearaudio tonearm „Magnify“
und Clearaudio cartridge
„Stradivari V2 MC“.
Pic. similar

User manual
Page 2 © clearaudio electronic GmbH, 2022-11
Dear Clearaudio customer,
Congratulation’s to your choice of the Innovation Compact turntable, a world class turntable,
handmade in Germany by Clearaudio electronic GmbH.
Resonance minimizing chassis sandwich construction in combination with the innovative motor unit
(low noise level and high turning moments), guarantees total isolation of resonances from the
turntable chassis, providing the best music reproduction and authentic High End imaging.
A high precision, maintenance free sinter bronze bearing is completing the analogue pleasure.
The Clearaudio patented CMB-Bearing-Technology, an inverted bearing with jewelled and polished
ceramic bearing shaft and a bronzed liner, provides frictionless analog enjoyment.
Please read this instruction manual carefully, to avoid any damages or loss of warranty.
This manual will help you for an easy setup and guarantees the highest pleasure for a long time.
We wish you a lot of musical enjoyments with your new Clearaudio Innovation Compact turntable.
Clearaudio electronic GmbH

User manual
Made in Germany Page 3
Safety instructions
1. General information
Check the turntable for any damage before using it. Do not connect the turntable if damaged!
Never connect the turntable if it has been dropped or gotten wet, contact your dealer to have the turntable checked.
Never expose the turntable to rain or moisture.
Never touch the power cord of the device with wet hands.
Regular visual inspections for defective insulation on the connection cable are also recommended for your own safety.
A damaged cable should be replaced immediately by a specialist!
Never pull on the power cord to unplug the device. Always pull directly on the plug!
The inside of the turntable is maintenance free. Never open the case or attempt to repair the unit yourself, since this
can lead to loss of warranty!
We recommend disconnecting the power supply from the mains if you do not operate the device for a longer period of
time.
The turntable does not feature an automatic shut-o mechanism.
Therefore, as soon as the stylus has reached the run-out groove, engage the tonearm lift and switch the turntable o.
Not suitable for children! Scope of delivery may contain small parts that can be swallowed.
2. Intended use
The Innovation Compact is a turntable for playing records.
The intended use of the Innovation Compact in accordance with the information provided in the user manual only.
The power supply may only be operated with maximum permissible connection values according to the technical data.
Any other use or modication of this product is not intended.
3. Location of installation
Avoid locations with direct sunlight, temperature uctuations and high humidity.
Likewise, avoid placing electronic devices near heaters, heat lamps, or other devices that produce heat.
The device is designed for operation at room temperature.
No objects with an open ame may be placed on or near the device (burning candles or similar).
4. Overload
The product is designed to comply with all necessary safety regulations. However, you should not leave the device
unattended under extreme loads.
5. Maintenance
Never use agressive cleaning detergent.
Donotusedryclothsforcleaningasthisgeneratesstaticelectricity. Suitable cleaning and care productsfromClearaudio
are available from www.analogshop.de or from specialist retailers.
The bearing of the turntable platter can be lubricated every 2 years with the oil provided.
Put 1 or 2 drops of the oil into the bearing for lubrication.

User manual
Page 4 © clearaudio electronic GmbH, 2022-11
6. Health information
Permanently high volume can lead to various types of hearing damage. Use high volume responsibly!
7. Service
The Innovation Compact turntable should be repaired during the guarantee period by the manufacturer only, otherwise
the warranty claim expires. All Clearaudio products should only be serviced by specialist retailers.
If, despite the high production standard, a service is necessary, the Innovation Compact turntable must be send to
Clearaudio through your dealer.
8. Transport
Use the original packing material for further transportation of the Innovation Compact turntable, otherwise serious
damage could occur.
Be sure to pack the device exactly as it was shipped.
Safe transport is only guaranteed in the original packaging.
Proceed in reverse as described for assembly when packing.
Always remove the turntable platter and replace the foam securing the sub-platter and cover the bearing with tape as
well. Otherwise serious damage can occur.
Remove also the pulley from the motor axle to avoid any damage during transport.
Clearaudio assumes no liability for any damage that may occur due to incorrect packing.
9. Disposal
Do not dispose this product together with other waste.
WEEE Reg. No.: DE26004446
10. CE Marking
This electronic product corresponds to the applicable guidelines for obtaining the CE mark.

User manual
Made in Germany Page 5
Contents
1. Packing overview ..............................................6
2. List of components............................................7 - 8
3. Installation and setup .......................................9 - 12
4. Fine adjustment of the motor ...........................13
5. Troubleshooting ................................................14 - 15
6. Technical data ...................................................16
Warranty information............................................17 - 18
User manual Stroboscope Testrecord ...................19 - 20

User manual
Page 6 © clearaudio electronic GmbH, 2022-11
1. Packing overview
Pic. 1: Packing overview
Accessories,
user manual,
warranty card,
Clearaudio Quality
Card,
Stroboscope
Testrecord
Innovation Compact
turntable chassis
incl. mounted lower
bearing part and
integrated motor unit;
optional: tonearm
Platter with
integrated bearing
upper part;
power supply;
optional: cartridge

User manual
Made in Germany Page 7
2. List of components
Clearaudio has developed a special and secure packing for your Innovation Compact turntable that
ensures a safe transportation.
Please keep this original packing, if you need to ship the turntable.
Below you nd the part list of the Clearaudio Innovation Compact turntable:
Pic. 2: List of components
12
3 4
5a 5b
1. Turntable body with mounted
lower bearing part 4. 3x Flat Pads
2. Platter with integrated upper
bearing part 5. Optional: Clearaudio
Universal
(Fig. 5 a) or Magny (Fig. 5 b) tonearm
Optional: 30 mm base for Universal tonearm
(not shown)
3. Power supply
Pic. 5b: Clearaudio Magnify tonearmPic. 5a: Clearaudio Universal tonearm

User manual
Page 8 © clearaudio electronic GmbH, 2022-11
Continuation of list
6 7 8
9 10 11
12 13 14
6. 1 Pair of white gloves 12. Bearing oil for occasional use
7. Grounding-wireforthe
Innovation
turntable (to connect in the bottom
bearing part)
13. Clearaudio Stroboscope Testrecord
(Art. No. AC038) to adjust the exact speed
8. Level gauge for the turntable
alignment 14. Optional in package: Clearaudio MC cartridge
9. 1 pcs. at belt 15. Optional in package:
Turntable + tonearm + cartridge
No illustration: cartridge alignment gauge
for
Magnify or Universal tonearm (optional)
10. 4 pcs. hex wrench; sizes:
# 1,5/# 2,5/#3/#7 16. Not shown: warranty card, Clearaudio Quality certicate card
11. Screw driver 17. Not shown: User Manual
Pic. 2.1: List of components
IMPORTANT NOTICE:
Please double check the tightness of all bolts, hardware, and mounting pods, as temperature
uctuations during transit may have caused the hardware to become loose.

User manual
Made in Germany Page 9
3. Installation and setup
The setup of the Innovation Compact turntable is easy as the turntable chassis is pre-assembled and
has been tested at the factory.
Please use the white gloves enclosed in order to avoid scratches or unwanted ngerprints (platter).
The
Innovation Compact turntable requires a space for setup of at least 18.90 inch x 19.29 inch.
18.90 inch
/ 480 mm
19.29 inch / 490 mm
Pic. 3: Required setup space

User manual
Page 10 © clearaudio electronic GmbH, 2022-11
Please follow the description step by step:
1.)
First take out the three black at pads out of the accessory bag. Place these at pads on your hi-
rack or another suitable base, where the nal position of your
Innovation Compact turntable will be.
2.)
After that, take the
Innovation Compact turntable body of the next packing layer and place the
spikes of the turntable on the at pads.
Pic. 4: Innovation Compact with tonearm base
Pic. 6: Oiling the bearing shaft
3.)
To avoid hum noises it can be necessary to ground the bearing. For that please plug in the provided
ground cable into the hole of the screw from the bearing at the bottom side of the turntable.
Pic. 5: Grounding the bearing of the Innovation Compact
4.)
Remove the protective security tape from the bearing housing.
Place two drops of the synthetic bearing oil on the ceramic bearing shaft (also available at www.
analogshop.de / Art. No. AC068).

User manual
Made in Germany Page 11
5.)
In the next step remove the lamination of the sensor, mounted on the turntable chassis
(picture 7: red frame).
Please remove the lamination extreme carefully and avoid any soiling and scratches.
6.)
6.1)
Take the platter with both hands (with white gloves) carefully out of the packing.
Please pay attention that the integrated bearing does not fall out of the platter!
The at side of the platter should face to the chassis and the side with the cut-out (for the record)
should face up.
6.2)
In the next step remove the lamination of the sensor on the bottom side of the platter.
Please remove the lamination extreme carefully and avoid any soiling and scratches.
6.3)
With both hands you can place the platter carefully onto the bearing.
Through a lightly (!!) up and down movement the platter will slip onto the bearing upper part
(picture 8).
Pic. 7: Removing the lamination
Pic. 8: Setting up the platter
Avoid major side forces to prevent any damages to the
ceramic bearing!
To avoid any damages on your bearing, the platter
should have room temperature before the setup begin
(approx. 20 ° Celsius).
Make sure with gentle pressure that the platter is
applying on the complete surface of the bearing.

User manual
Page 12 © clearaudio electronic GmbH, 2022-11
7.)
To install the tonearm and / or to mount and adjust a cartridge, please follow the user manual of the
manufacturer.
8.)
The following nal adjustment is very important:
Please ensure that your turntable rack is in a levelled position.
Please check with the delivered level gauge, if your Innovation Compact turntable is in a levelled
position.
You can adjust each of the turntables feet to get the turntable levelled (Pic. 9).
To adjust the height, rst turn the middle part of the feet (Pic. 10 a; green arrow), then you can
twist the end part (Pic. 10 b, red frame) to the desired height.
After the adjustment, please make sure, to turn the middle part again to x the selected position.
Pic. 9: Alignment of the
turntable
9.)
Please connect the plug of the power supply with the linkage of the turntable.
After that connect the power supply with the electric power supply.
Only if the turntable is in a levelled position you will get the best results with your Innovation
Compact turntable.
Pic. 10 a: Middle part Pic. 10 b: End part
Pic. 11: Connection of power supply and motor
10.)
Place the at belt around the platter and around the
motor pulley.
By pushing the sensor-switch, marked with “33 1/3”
on the motor, the turntable starts to spin until 33 1/3
rpm is reached.
Aftertheinitialsetupwerecommendto let the turntable
spin for at least 15 to 30 minutes.
This ensures a smoother break in.

User manual
Made in Germany Page 13
4. Fine adjustment of the Innovation Compact motor
The motor adjustment is already pre-set at the factory. Through the transport some small speed
deviations can occur. Please check the speed before using the turntable for the rst time.
For the correct adjustment of the speed please put the recommended Clearaudio Stroboscope
Testrecord on the platter. Follow hereby the instruction of the Stroboscope Testrecord user manual.
To check the speed with highest accuracy please use the Clearaudio Speed Light (Art. No. AC039)
(www.analogshop.de).
On the front side of your turntable there are three setting trimmers (see pic. 11).
Pic. 12: Fine adjustment of the motor (on the frontside)
- Left trimmer = setting 33 1/3 rpm
(near turntable motor)
- Middle trimmer = setting 45 rpm
- Right trimmer = setting 78 rpm
(near turntable bearing)
If you like to adjust the speed 33 1/3 rpm, take the Aluminum screw driver (see accessories) and
turn the left trimmer until you have reached the right speed according to the Stroboscope Testrecord
(see user manual
Stroboscope Testrecord ).
- Turning the trimmer counter clockwise = reduces the turntable speed
- Turning the trimmer clockwise = raises the turntable speed
Please proceed with the speed adjustment for 45 rpm and 78 rpm in the same way!
Please note:
If the turntable does not reach the correct speed, the sensor or the scale ring could be dirty or dusty.
To clean the sensor, please take o the platter very carefully!
Clean the sensor and the scale ring with a little isopropyl alcohol and a cotton bud.
Be careful and avoid any scratches on the sensor or the scale ring!
If the motor has further more speed variations please contact your nearest authorized Clearaudio
dealer or directly the Clearaudio factory (address on page 13).
If the turntable is not in use, disconnect the unit completely from the power supply by removing the
main plug from the socket.
Now you are nally ready to play your vinyl records.
We wish you a lot of pleasure with your new Innovation Compact turntable.

User manual
Page 14 © clearaudio electronic GmbH, 2022-11
5. Troubleshooting
If you have a problem with your Innovation Compact turntable, rst check the possible causes to
rule out incorrect operation.
If the error persists, please contact your dealer!
Never try to open the device and/or repair it yourself, this will void the warranty!
Error Cause Measure
Device does not
work Is the power cord plugged in? Check the connection.
No sound
The tonearm and phono stage
are not properly connected. Check the cable connection between the tonearm and the phono stage.
Is the amp turned on? Check the power supply to the amplier.
The volume on the amplier/
loudspeaker is set too low or on
„mute“.
Check the volume settings.
Is the cartridge protective cap
still attached? Remove the cartridge‘s protective cap.
Is the tonearm in the raised
position? Lower the tonearm into the lead-in groove.
Is the stylus damaged? Check the stylus and have the cartridge checked
by a specialist if necessary.
Bad sound /
noise
Is the record or the stylus dirty or
damaged? Clean the record / or the cartridge. Clearaudio oers many helpful accessories for care and
cleaning. In the event of damage, we recommend
an assessment by a specialist and, if necessary,
an exchange.
Is the cartridge properly mounted
into the tonearm? Check the installation using the relevant user manual and correct them if necessary.
Has the tracking force been set
too high? Adjust the tracking force.
Is the correct operating mode
(MM / MC) set on the amplier? Check the settings of your phono stage.
The pre/amp does not have
enough gain. Check the settings of your phono stage.
Pre/amp is mismatched. Swap the plugs of the turntable that are connected
to the left and right outputs.

User manual
Made in Germany Page 15
Needle bounces
or slides across
record
Is the record or the stylus dirty
or damaged? Clean the record / or the cartridge. Clearaudio oers many helpful accessories for care and
cleaning. In the event of damage, we recommend
an assessment by a specialist and, if necessary,
an exchange.
Has the tracking force been set
too high? Adjust the tracking force.
Is the record deformed or
scratched? Use a record clamp or replace the record.
Is the turntable level? Check the alignment of the turntable and adjust
if necessary.
Platter does not
turn
Is the drive belt properly
attached? Check the position of the drive belt.
Is the power cord connected
properly? Check the connection.
No speed was selected / speed
selection in position „0“/“OFF“. Select a speed and start the turntable.
Noisy sound Is the drive belt properly
attached? Check the position of the drive belt. Is it too loose and needs to be changed?
Humming noises
Contact problems with the signal
connections (e.g. cinch plugs,
adapters for extensions)
Check all connections; reduce the level on the
(pre-)amplier to a low volume for acoustic
checking of gross errors.
Metal housing acts as an
antenna and catches hum. It can be helpful for conductivity to connect the metal parts of the turntable to the ground of
the (phono) preamplier. The turntable provides
a grounding terminal for this purpose. Use a
suciently thick wire to establish the ground
connection.
Thepickup pinsaremixedup,not
connected correctly or defective. Check the pin assignment of the pickup.
The music doesn‘t
sound like
usual
Wrong speed selected. Check the record for recommended speed.
There are also records in LP format (30 cm) that
have to be played at 45 rpm (“maxi singles”) and
small records in single format (17 cm) that have to
be played at 33 rpm (so-called “ EP‘s“).
The turntable is spinning too
fast/too slow. Adjust the speed according to the operating instructions.

User manual
Page 16 © clearaudio electronic GmbH, 2022-11
6. Technical data
Construction details: • Resonance-optimised chassis shape
• Made of bullet proof wood and aluminium with precision
CNC machined surface
• All turntable feet are nely adjustable
• Playback with two tonearms possible
Speed options: 33 ⅓, 45, 78rpm
Drive unit: • High torque 24V DC motor exclusively made for
Clearaudio; Optical Speed Control (OSC) in real time
through infrared sensor
• Decoupled DC motor in chassis;
resonance damping device; belt-drive
Bearing: Clearaudio CMB ceramic magnetic bearing in main platter /
upper drive platter assembly. Inverted bearing in lower drive
platter.
Platter: 70mm / 2.75 inch main platter, made out of synthetic material
with high-density and excellent dimension stability, precision
CNC machined surface, solid stainless steel sub-platter,
dynamically balanced
Speed accuracy (measured): < ± 0.08%
Power consumption: Max. consumption: 9.3 watts
Consumption in operation: 2.5 watts
Standby mode: 2.5 watts
O mode: 0.0 watts
Total weight: Approx. 12kg (without tonearm and power supply)
Dimensions (W/D/H): Approx. 18.11 x 19.09 x 6.18 inches
(with tonearm base, without tonearm)
Dimensions (W/D/H): Approx. 460 x 485 x 157mm
(with tonearm base, without tonearm)
Manufacturer’s warranty: 5 years*
* Provided that the warranty card is correctly completed and returned to Clearaudio, or your product is registered
online at https://clearaudio.de/en/service/registration.php, within 14 days of purchase.

User manual
Made in Germany Page 17
The full, extended warranty period for the Innovation Compact turntable is 5 years. To receive this full
Clearaudio warranty, you must either complete and return the relevant section of the warranty registration
card to Clearaudio, or register your product online at https://clearaudio.de/en/service/registration.php,
within 14 days of purchase. Otherwise only the legal warranty of 2 years can be considered.
The full 5 year warranty can only be honoured if the product is returned in its original packing.
ENGLISH
WARRANTY
For warranty information, contact your local Clearaudio distributor.
RETAIN YOUR PURCHASE RECEIPT
Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred
to as necessary for insurance purposes or when corresponding with Clearaudio.
IMPORTANT
When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase.
Your purchase receipt or invoice is adequate for such proof.
FOR U.K. ONLY
This undertaking is in addition to a consumer‘s statutory rights and does not aect those rights in any way.
FRANÇAIS
GARANTIE
Pour des informations sur la garantie, contacter le distributeur local Clearaudio.
CONSERVER L‘ATTESTATION D‘ACHAT
L‘attestation d‘achat est la preuve permanente d‘un achat de valeur. La conserver en lieu sur pour s‘y reporter aux ns
d‘obtention d‘une couverture d‘assurance ou dansle cadre de correspondances avec Clearaudio.
IMPORTANT
Pour l‘obtention d‘un service couvert par la garantie, il incombe au client d‘établir la preuve de l‘achat et d‘en corroborer
la date. Le reçu ou la facture constituent des preuves susantes.
DEUTSCH
GARANTIE
Bei Garantiefragen wenden Sie sich bitte zunächst an Ihren Clearaudio Händler. Heben Sie Ihren Kaufbeleg gut auf.
WICHTIG!
Die Angaben auf Ihrer Quittung erlauben uns die Identizierung Ihres Gerätes und belegen mit dem Kaufdatum die
Dauer Ihrer Garantie-Ansprüche. Für Serviceleistungen benötigen wir stets die Gerätenummer. Diese nden Sie auf dem
Typenschild auf der Rückseite des Gerätes oder auch in der beigefügten Garantie-Registrierkarte.
NEDERLANDS
GARANTIE
Voor inlichtingen omtrent garantie dient u zich tot uw plaatselijke Clearaudio.
UW KWITANTIE, KASSABON E.D. BEWAREN
Uw kwitantie, kassabon e.d. vormen uw bewijs van aankoop van een waardevol artikel en dienen op een veilige plaats
bewaard te worden voor evt, verwijzing bijv, in verbend met verzekering of bij correspondentie met Clearaudio.
BELANGRIJK
Bij een evt, beroep op de garantie is het de verantwoordelijkheid van de consument een gedateerd bewijs van aankoop
te tonen. Uw kassabon of factuurzijn voldoende bewijs.

User manual
Page 18 © clearaudio electronic GmbH, 2022-11
ITALIANO
GARANZIA
L’apparecchio è coperto da una garanzia di buon funzionamento della durata di un anno, o del periodo previsto dalla
legge, a partire dalla data di acquisto comprovata da un documento attestante il nominativo del Rivenditore e la data di
vendita. La garanzia sarà prestata con la sostituzione o la riparazione gratuita delle parti difettose.Non sono coperti da
garanzia difetti derivanti da uso improprio, errata installazione, manutenzione eettuata da personale non autorizzato
o, comunque, da circostanze che non possano riferirsi a difetti di funzionamento dell’apparecchio. Sono inoltre esclusi
dalla garanzia gli interventi inerenti l’installazione e l’allacciamento agli impianti di alimentazione.
Gli apparecchi verranno riparati presso i nostri Centri di Assistenza Autorizzati. Le spese ed i rischi di trasporto sono a
carico del cliente. La casa costruttrice declina ogni responsabilità per danni diretti o indiretti provocati dalla inosservanza
delle prescrizio-ni di installazione, uso e manutenzione dettagliate nel presente manuale o per guasti dovuti ad uso
continuato a ni professionali.
ESPAÑOL
GARANTIA
Para obtener información acerca de la garantia póngase en contacto con su distribuidor Clearaudio.
GUARDE SU RECIBO DE COMPRA
Su recibo de compra es su prueba permanente de haber adquirido un aparato de valor, Este recibo deberá guardarlo
en un lugar seguro y utilizarlo como referencia cuando tenga que hacer uso del seguro o se ponga en contacto con
Clearaudio.
IMPORTANTE
Cuando solicite el servicio otorgado por la garantia el usuario tiene la responsabilidad de demonstrar cuándo efectuó la
compra. En este caso, su recibo de compra será la prueba apropiada.

User manual
Made in Germany Page 19
Stroboscope Testrecord
TheClearaudio StroboscopeTestrecord satises the highest demands for an exact speed adjustment
for turntables. Dramatic sound improvements can be reached only with exact calibrated speeds.
- Optimal adjustment for turntables -
To adjust the exact speed, please choose the side for 50 / 60 Hz, or
the other side for the use with the speed light rst. If you choose the
side without the speed light source, you can use the regular light source
for the installation, either 50 Hz (outer scales) or 60 Hz. The scales are
graduated in three dierent reading options:
33.3 Hz, 45 Hz and 78 Hz (starting from the outer diameter).
Please place the
Stroboscope Testrecord on your turntable platter and start the engine of your
turntable. The big advantage of the Clearaudio Stroboscope Testrecord is, that you can place
your cartridge onto the Stroboscope Testrecord , while measuring the speed, as there are grooves
provided on the disc. This means, for the rst time a real time speed analysis is possible under
realistic circumstances.
If you have the impression that the horizontal lines move on the scale, you should set or readjust
the speed of the motor again.
- If the lines move clockwise, the speed is too fast.
- If the lines move counter clockwise, the motor speed is too slow.
Please correct the speed on your motor or turntable until you have the impression that the lines
stopped moving. After that you have reached the exact speed and you can enjoy the full potential
of your vinyl collection again.

User manual
Page 20 © clearaudio electronic GmbH, 2022-11
Ifyouusethe SpeedLight (Art.No.AC039)youcanreachan even higher or more
accurate adjustment, completely independent of the power line or frequency
of your country. As well, the 300 Hz calibrated light, used as an external light
source is completely independent from possible power line uctuations, which
could inuence the result by regular light. The 300 Hz of the Speed Light are
generated by a stabilized quartz oscillator and permit a very exact adjustment.
Please put the Stroboscope Testrecord with the ne lines upward on your
turntable. Here you also have the possibility to choose between two dierent
speeds.
With the outside scale you can detect the speed of 33 Hz and with the inside scale you can detect
the speed of 45 Hz. Again, the big advantage of the Clearaudio Stroboscope Testrecord is, that you
can place your cartridge onto the stroberecord, while measuring the speed, as there are grooves
provided on the disc. This means, for the rst time a real time speed analysis is possible under
realistic circumstances.
Press the button of the speed light source and place it parallel over to the scale and adjust the motor
or turntable speed until the horizontal lines do not move anymore.
- Tip -
As more accurate your turntable speed is adjusted, as better the overall sonic appearance of the
record playback will be!
It is mandatory to check the speed several times through out the year, to ensure that other inuences
are not minimizing the sound quality.
Technical Data:
Speed Light
Light source: Blue LED / 300 Hz precision light source (calibrated)
Battery: V23GA – 12 V – Alkaline (Art. No.: AC039/B)
(Technical changes are subject without notication)
Date: 2022-11
Clearaudio electronic GmbH
Spardorfer Str. 150
91054 Erlangen
Germany
Phone: [phone]
Fax: [phone]
www.clearaudio.de
www.analogshop.de
[e-mail]