Clevertronics CLP LIFELIGHT Pro User manual

1942401
V1.1
9 September 2020
Zoneworks, HIVE and DATA Monitored Options
Fittings with part numbers -ZW, -HVG, -DATA are fitted with Zoneworks communications modules
(nodes). These fittings are monitored using either Powerline Carrier Technology that utilize the power
cable to provide data communication, RF transceiver modules operating in the ISM band or a dedicated
data cable to/from data routers installed on a dedicated data trunk connected to a central Server (can also
be connected via Ethernet/Internet/Fibre)
. Zoneworks software on the server is used to monitor,
coordinate testing and collate test data from each fitting. Zoneworks Fittings can be commissioned by a
single push of the test switch or by scanning the supplied barcode. The LED Test Switch indicator provides
a multifunction indication of the status of the fitting during testing and normal operation:
Option
State
LED Operation
ZW, HVG, DATA
Commissioned
LED on Solid (Green)
ZW, DATA Un-commissioned
Batt plugged-in: yellow 1s, green 1s
Batt unplugged: red 1s, off 1s
HVG Un-commissioned
With network connectivity
Batt plugged-in: yellow 1s, green 1s
Batt unplugged:
red 1s, off 1s
HVG Un-commissioned
Without network connectivity
Batt plugged-in: yellow 250mS, green
250mS, yellow 250mS, green 250mS,
green 1s
Batt unplugged: red 250mS, off
250mS, red 250mS,off 250mS, off 1s
ZW, DATA
Emergency Light Test In Progress
LED flashes at yellow 5s , 0ff 1s
HVG
Emergency Light Test In Progress
LED flashes at yellow 1s , 0ff 1s
In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to
the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of
a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA
version)
DALI EM Option
Luminaires with part numbers having -DALI are fitted with DALI modules (nodes) that facilitate connection
and integration to 3rd Party Lighting Control Systems. Before installing the -DALI fitting please confirm
that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI
fitting will be addr
essed and configured into the control system by the Lighting Control System
Commissioning Technicians and not Clevertronics.
State
LED Operation
Commissioned/ Un-commissioned LED on Solid (Green)
Emergency Light Test in progress LED flashes at 1s On (Yellow) & 1s Off
“IDENTIFY COMMAND” Fitting goes into emergency mode for 10 seconds
A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network OR a 5/6way
“structured wiring system” lead and plug facilitating the power and DALI connection. DALI connections
are marked as Da Da.
Clevertest and Clevertest Plus
Refer to the supplementary operation guide supplied with the Product.
After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red
flashing for a period up to 2 minutes.
Maintained fittings (CLIFEM-PRO-SM-WP-xx-yy-ww) cannot be scanned with a camera using the
Clevertest Plus App as the maintained light source interferes with the camera scanning function. To
register the fitting manually enter the serial number from the QR code and visually read the test result
and enter manually into Clevertest Plus App.
CLP™ LIFELIGHT Pro Surface Mount
Weatherproof Emergency Luminaire
Installation & Maintenance Instruction Leaflet
NOTE: Standard product codes with this symbol
are enabled with Clevertest Plus capability. Please refer to the
operation guide supplied with the product for details.
Australia (Head Office)
Website: www.clevertronics.com.au
Email: [e-mail]
Phone: [phone]
Fax: [phone]
UK OFFICE
362 Stockley Close
West Drayton UB7 9BL
Phone: [phone]
Models:
CLIFEx-PRO-SM-WP-xx-yy-ww
Testing:
Options:
Manual Test
xx = Blank
yy = TP
Tamperproof
Zoneworks
xx = ZW
ww = BLK
Colour, Black
Z/W DATA
xx = DATA
x=Blank
Non-Maintained
DALI Registered
xx = DALI
x=M
Maintained
HIVE
xx = HVG
Spare Parts:
1550231
BATT:LP 3.2V 6400mAh.200mm lead, No Brkt
8050170
HWSUB: CT10668-D2
8002908
PCA: CT10142-L9 2C250/475mA CTP UK Vert Connectors
Important:
It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant British Standards.

1942401
V1.1
9 September 2020
Installation:
Please follow the steps below to correctly install the product;
•The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer
than 300mm is not expected.
•Remove the Lid from the Base by using a flat screwdriver to release the snap fits (see below)
•For products requiring a Corridor or Area Lens, replace Lens now (see below)
•Cut/Drill out Cable Entry points (A=End Entry, B=Rear Entry)
•Drill out the required fixing holes on the Base (see image below, C=Junction Box fixing)
•Mark holes on mounting surface (use drilled out holes on the Base as a template)
•Insert Mains Cables & mount Base using appropriate fixings to ensure a secure installation
(mounting points must be sealed appropriately to ensure proper protection from water ingress)
•Mount Base using appropriate fixings to ensure a secure installation (pre-drill holes if required)
•Terminate the Mains Cables into terminal block. Ensure Live, L & Neutral, N wires are connected
as per Terminal Block Label. Earth is not required, if Earth is brought in, it can be terminated to E.
•Re-attach Lid Assembly, ensuring to align Mains Connector Pins into Terminal Block
•Where QR/Barcode labels have been supplied with the product, ensure one of the QR/Barcode
labels is adhered to a visible surface on the base of the product.
•If the CTP capabilities are activated, please affix the CTP Status Label to a visible surface.
Dimensions:
Lid Removal / Lens Replacement:
STEP 1 – Insert flat screw driver and lever to
remove lid
STEP 2 – Remove the two coloured screws and
push out Bezel/Lens
STEP 3 – Release Lens from the Bezel
STEP 4 – Insert required Lens followed by Bezel
and re-insert coloured screws and Lid
Note: for Corridor Lens ensure the two pins
engage into the PCA
Note:
This luminaire (with reinforced insulation between control/LED terminal and AC supply) contains non-
user replaceable light source and battery - to be replaced (if required, refer installation instructions for
battery replacement) by Clevertronics service personnel/agents or a registered electrician.
Battery Replacement:
1. Prior to any work, isolate the power to the luminaire that requires battery replacement
2. Open the fitting by removing the Lid as shown in Lid Removal.
3. Remove the Battery Connector from the Emergency Driver board.
4. Remove the battery from the Lid pressing out one end first.
5. Replace battery, reconnect battery connecter to Emergency Driver board.
6. Reinstall the Lid, ensure both ends are clipped in.
Testing Procedure:
Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24
hours. Conduct the following tests:
•The emergency lamp must illuminate for at least 180 min after disconnection from the mains. If the
unit fails to illuminate for the requisite time, remedial action must be taken to repair the situation
and once completed, the unit must pass a subsequent test.
•Press and hold Test Button or switch Off Mains Supply, check that the emergency lamp is On.
•Release the Test Button or Switch On Mains Supply, check that the emergency lamp is Off (Non-
maintained operation).
Trouble Shooting:
Below are a list of common problems and their possible causes:
Fault: The Green LED indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected.
Test Switch for damage.
Fault: Lamp does not illuminate in emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault: Lamp illuminates in emergency mode, but only stays on for a short period.
Check: Battery has been allowed to charge for at least 24 hours.
Battery for damage.
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The battery in this fitting has been selected to give excellent long life
performance in a controlled IEC 60598-2-22 testing environment. Excessive battery cycling will reduce
through-life performance and may lead to premature battery failure. Battery warranty claims, as a result
of such abuse, are specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
https://clevertronics.co.uk/product-warranty-statement/