Original BTC Primo Table User manual

Primo Table & Floor
Instruction Manual
US-FF463N / US-FT311
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
MADE INBRITAIN
L
N
Live
KEY
Neutral
Earth
L =
N =
=
*Mains
Supply
Fitting
*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
BROWN
GRN/YEL
BLUE
BROWN
GRN/YEL
BLUE
MADE INBRITAIN
Primo Floor Light
US-FF463N
Primo Table Light
US-FT311
Safety Instructions
These instructions are provided for your safety in order to prevent the risk of Fire, Electric
shock or Injury. Please retain for future reference. When fitting is in operation, some parts
will become hot; take care when using/handling.
- Ensure the lamp type and max wattage is followed- do not exceed. Take care not to
overtighten lamp.
- Do not touch the lamp (bulb) or lamp holder while in operation, as both become very hot.
- Turn off and unplug fitting, leaving lamp to cool before changing lamp. Dispose of old
lamps carefully.
- Never leave a fitting without a lamp in position.
- Keep light fitting away from combustible materials such as soft furnishings.
- Ensure children do not play with the light fitting.
- Ensure the light is positioned on a solid, level and non-slip surface and make sure the
position of the cable does not pose a trip hazard.
- If the electrical flex or electrical components become damaged at any point, the fitting
must be unplugged from the power supply immediately and not operated until the
damaged parts are fixed/replaced.
- For use in a dry, indoor environment only. Ensure the fitting does not come into contact
with any liquids.
Cleaning and Maintenance
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or
abrasives. Glass can be cleaned using a soft damp cloth with a mild detergent or suitable
glass cleaner if necessary. Switch off power to the fitting before cleaning. Spare parts are
available for this product, please see contact details on the reverse.
MADE IN BRITAIN
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and
contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
v1.2-05.19
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
ENG WARNING – RISK OF FIRE AND ELECTRIC SHOCK.
SUITABLE FOR DRY LOCATIONS ONLY
FR ATTENTION – RISQUE D’INCENDIE, RISQUE DE CHOC.
POUR EMPLACEMENTS SECS SEULEMENT

*After 2004, wiring installation colours changed:
LIVE Brown replaces Red
EARTH Green/Yellow sleeving
NEUTRAL Blue replaces Black
120V ac 60Hz IP20
Primo Table & Floor
MADE INBRITAIN
E26 A BALL
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
INCANDESCENT
CFL
ECO-HALOGEN
LED
40W MAX
11W
n/a
7W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
US-FF463N Primo Floor Light US-FT311 Primo Table Light
Contents
Assembling Base
Adjusting Shade
1
2
3
- With one hand supporting the shade, gently loosen the
clamp handle (2). One quarter-turn, in an anti-clockwise
direction should be sufficient.
- The shade can then be moved into desired position,
ensuring the clamp remains attached to the stem, but
without applying excessive force to the washers on the
inside of the clamp. Ensure the shade is still supported
whilst adjusting position.
- Secure in place by gently tightening clamp handle,
taking care NOT to overtighten, as this can damage
the clamp.
- Do not adjust the position of the shade without
loosening the clamp first, as this will damage the
washers.
A
A Shade/Stem/Cable Assembly
B Base*
*This will be detached from stem in floor version
A Stem
B Thread
C Coupler
D Base
Place base on a level floor (non-slip surfaces work best during assembly).
STEP 1
Support the stem and shade with both hands, then insert the thread into the coupler on the base. Screw the stem into
the coupler until a tight, firm fit is achieved (the thread should no longer be visible).
STEP 2
B
A
C
B
D