Clevertronics L10 LVP2LEDM-P Series Installation and operating instructions

1948806 V1.0 25 October 2018
Clevertronics Clevertest and Clevertest Plus
Refer to the supplementary operation guide supplied with the Product.
After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red
flashing for a period up to 2 minutes.
The diffuser will require removal to gain access to the Test/Status Switch and LED.
Maintained fittings (LVP2LEDM-P-xx-yy) cannot be scanned with a camera using the CleverSparky App
as the maintained light source interferes with the camera scanning function. To register the fitting
manually enter the serial number from the QR code and visually read the test result and enter manually
into CleverSparky.
Zoneworks and DATA Monitored Options
Battens with part numbers including -ZW, -DATA are fitted with Zoneworks communications modules
(nodes).These battens are monitored using either Powerline Carrier Technology that utilises the power
cable to provide data communication or a dedicated data cable to/from data routers installed on a
dedicated data trunk connected to a central Server (can also be connected via Ethernet/Internet/Fibre).
Zoneworks software on the server is used to monitor, coordinate testing and collate test data from each
batten and can be commissioned by scanning of the supplied barcode. The LED Test Switch indicator
provides a multifunction indication of the status of the batten during testing and normal operation:
State
LED Operation
Commissioned
LED on Solid (Green)
Un-commissioned
LED flashes at 0.5Hz (0.5s Green, 0.5s Yellow)
Emergency Light Test In Progress
LED flashes at 3s On (Yellow) & 0.5s Off
In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to
the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of
a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA
version)
DALI EM Option
Battens with part numbers including -DALI are fitted with DALI modules (nodes) that facilitate connection
and integration to 3rd Party Lighting Control Systems. Before installing the -DALI batten please confirm
that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The -DALI
batten will be addressed and configured into the control system by the Lighting Control System
Commissioning Technicians and not Clevertronics.
State
LED Operation
Commissioned/ Un-commissioned
LED on Solid (Green)
Emergency Light Test in progress
LED flashes at 1s On (Yellow) & 1s Off
“IDENTIFY COMMAND”
Fitting goes into emergency mode for 10 seconds
A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI
connections are marked as Da Da.
L10™ 2ft LED Weatherproof Vandal Resistant Batten
Installation & Maintenance Instruction Leaflet
Victoria (Head Office & Manufacturing)
195 Chesterville Rd
Moorabbin VIC 3189
Phone: [phone]
Fax: [phone]
New South Wales
Phone: [phone]
Fax: [phone]
Queensland
Phone: [phone]
Fax: [phone]
South Australia/Northern Territory
Phone: [phone]
Fax: [phone]
Western Australia
Phone: [phone]
Fax: [phone]
New Zealand
Phone: [phone]
Designed in Australia to comply with the requirements of
AS2293.3: 2005 and AS/NZS CISPR15: 2011
NOTE: Standard product codes with this symbol are
enabled with Clevertest Plus capability. Please refer to the
operation guide supplied with the product for details.
Models:
LVP2LEDM-P-xx-yy
Testing :
Options:
Manual Test
xx = Blank
4HR Battery
yy=4HR
Zoneworks
xx = ZW
Z/W DATA
xx = DATA
DALI Comp.
xx = DALI
Clevertest
xx = CT
(NOTE: -CT Products supplied with the Clevertest Plus Symbol are activated with
Clevertest PLUS capability. Please refer to the operation guide supplied with the product for
details).
Spare Parts:
1330055
LED Driver - LC 50w 350-1050mA, 20-50V
LCPLED-38V120C-CKIT
LED Power Pack,38V 120mA,L10
1530260
BATT:L10 6.6V 2500mAh.200mm lead.SBS.
8002699
PCA:LED Strip 5P8S, ALS-50-840-3-01-C
Important:
It is illegal for anyone, except for a licensed electrician toinstall or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant Australian and International Standards.

1948806 V1.0 25 October 2018
Installation:
The Vandal Resistant Batten is a surface mount fitting.
The batten can be attached directly to any solid surface by drilling the base internal mounts as required.
Refer to the Dimensions Section for mounting points.
The batten can also be mounted to Unistrut utilizing the four (4) recessed screw holes on the back of the
case. Refer to Dimensions section.
* If the CTP capabilities are activated please affix the CTP status Label to a visible surface.
Sealing:
When drilling through the fitting base, a suitable silicone sealant must be applied to maintain the IP
rating. Always use a sealant that remains flexible. Apply enough sealant so that the material oozes out
completely around the washer when the bolt or screw is tightened.
Always use a gland or screwed conduit adapter. With conduit ensure that the other end of the conduit is
not left open. Even if it is inside the building, it allows water vapor and insects to enter the fitting. A
rubber washer and silicone sealant should also be used between the fitting body and the conduit nut
inside the fitting to guarantee a water-tight seal. Use PVC cement to seal all conduit joints. Glands are
intended for round cable and will not seal against TPS. Even when properly installed using round cable,
sealant may be necessary in extreme weather exposure.
Networking:
When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the
relevant Smart Node PCA.
Dimensions:
Testing:
Once connected to the 240V mains supply, the batten must be allowed to charge the battery for at least
24 hours. Conduct the following tests:
•For the first test, the emergency lamp must remain illuminated for at least 2 hours after
disconnection from the mains supply.
•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are
required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails
to remain illuminated for the requisite time, remedial action must be taken to repair the situation
and once completed, the unit must pass a subsequent test. For more specific information, please
refer to the current edition of the AS 2293.3 Standard.
Batten Maintenance:
Battery Replacement:
•Use only the battery recommended in the
Spares List on this instruction.
Trouble Shooting:
Below are a list of common problems and their
possible causes.
Fault: The Green LED Test Switch
indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault: Lamp does not illuminate in
emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault: Lamp illuminates in emergency
mode, but only stays on for a short
period.
Check: Battery has been allowed to charge for
at least 24 hours.
Battery for damage.
Rated Emergency Lumen Output in accordance with AS2293.1 (refer to
spacing tables for installation positions):
Refer to the Technical Label on the fitting for Classification Information.
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The battery in this fitting has been selected to give excellent long life
performance in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-
life performance and may lead to premature battery failure. Battery warranty claims, as a result of such
abuse, are specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
http://clevertronics.com.au/terms-conditions-sale-australia-nz/