Lampo Vogue 575 W User manual

L
L
Li
i
ig
g
gh
h
ht
t
t
e
e
ef
f
ff
f
fe
e
ec
c
ct
t
t:
:
:
A
A
AS
S
S7
7
78
8
8/
/
/A
A
A
V
V
VO
O
OG
G
GU
U
UE
E
E
5
5
57
7
75
5
5W
W
W
USER’ S MANUAL
This manual must be considered an integral part of the projector.

1
BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE
INSTRUCTIONS IN THIS MANUAL.
QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE
INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR.
BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE
VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR.
FOR ANY DOUBT, CONTACT YOUR SUPPLIER OR SEND AN E-MAIL TO:
[email protected]
SOLID: Objects exceeding 12mm diameter
WATER: Non protected
Minimum distance from lighted objects (meters)
Rated maximum ambient temperature (35°C indoor with ventilation)
Connection must be made to a power supply system fitted with efficient
earthing (EN60598-1 – Class I fixture)
Replace any cracked protective shield, dichroic filter or lens
Ignitor circuit lamp have very high voltage
Index
Dimensions and weight ---------------------------------------------------------------------------------- page 2
Admissible environmental conditions ----------------------------------------------------------------- page 2
Storage ------------------------------------------------------------------------------------------------------ page 2
Power supply ---------------------------------------------------------------------------------------------- page 2
Lamp replacement --------------------------------------------------------------------------------------- page 3
Sound animated unit ------------------------------------------------------------------------------------ page 3
Black-out --------------------------------------------------------------------------------------------------- page 4
Maintenance ----------------------------------------------------------------------------------------------- page 4
Spare parts ------------------------------------------------------------------------------------------------- page 4

2
Dimensions & weight
Weight: 23 Kg
Admissible environmental conditions
The projector was engineered and produced to function in indoor areas with an air temperature ranging between 0° and 35°C
and with a humidity level between 30 and 90%.
When choosing the installation, please make sure that the device is not exposed to extreme heat or in small area.
Storage
The projector, in its original packing, must be kept in covered, dry areas with a temperature between –10°C and +50°C.
Power supply
The projector can be feed with voltage between 210Vac and 240Vac (on the projector body is specified if 50 or 60 Hz). Over-
voltage caned damage the electronic parts of the projector or reduce the lamp life. It is advised to check the electric system
before installation.
Use the cable provided inside the junction box. The power line must be protected by a differential MGT breaker, while metal
parts, that might be electrically charged through the projector must be grounded. Make sure the projector does not pull the
cable in all different working positions, and that sources of heat are not placed in the vicinity.
Connect the fixture to the mains with the enclosed power cord and plug. (Fan and electronic board on the projector) (Power
supply on the external ballast). See the table for the colours of the connection-cable.
When in doubt, consult a qualified electrician.
Be careful with your operations. With a high voltage you can suffer a dangerous electric shock when touching the
wires! Inside the projector, the ignitor circuit have very high voltage, over 7Kv.
The User must ensure that the power supply is provided with a highly sensitive differential circuit breaker 30m/A to
protect the projector from indirect contacts, and that the grounding system PE is working properly.
Don’t power the projector with a dimmer circuit

3
Lamp replacement
1) Disconnect the projector from the main power supply
2) Unscrew the screw of the lamp cover (top of the projector)
3) Remove the lamp, taking care to wear proper protective gloves
4) Insert a new lamp
5) Close the lamp cover and tight the screw
Use HM/MSI 575 discharge lamp, socket SFc10
DISCHARGE LAMPS CONTAIN SUBSTANCES THAT CAN POLLUTE THE AMBIENCE. DISPOSE OF USING
THE APPROPRIATE REFUGES (TOXIC).
Sound animated unit
Sound animated unit with a rotating mirrored reflector creating a star bust of beam. Its effect is widened and enhanced by a
mirrored accessory with a central dichroic prism rotating to the music, that changes the colours of the rays according to their
position.
Rear of the projector:
It is possible to rotate the screws to adjust the parameters of the sound animated unit.

4
Black-out
Vogue has the black-out system, see the drawing:
Main voltage of black-out system is 14V.
Maintenance
If the protective grill or any of the lenses become damaged or broken they should be replaced. If the lamp becomes damaged or
deformed in any way it must be replaced. To ensure the reliability of the projector it should be kept clean. It is recommended
that the lenses and the fan should be regularly cleaned (every two months) to maintain an optimum light output. Do NOT use
any type of solvent on filters and lenses.
Spare parts
When ordering spare parts for the projector remember to mention the model and serial number which can be found on the plate
at the rear of the projector.
Call your area dealer or feel free to contact the manufacturer for any additional assistance.
The improper use of this projector, cancel the guarantee and our responsibility. All the information have been written and driven with
extreme care; however, we do not engage us any responsibility for contingent errors or omissions. We reserve the right to modify and/ or
improve our product as we retain necessary, without subsequent warning or notice. It is forbidden any complete or partial reproduction of
this handbook, if not expressly authorized.