Clevertronics L10 LJELED-40 Series User manual

1947245 V1.5 10 October 2017
Testing:
Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24
hours. Conduct the following tests:
•For the first test, the emergency lamp must remain illuminated for at least 2 hours after disconnection
from the mains supply.
•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are
required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit fails
to remain illuminated for the requisite time, remedial action must be taken to repair the situation and
once completed, the unit must pass a subsequent test. For more specific information, please refer
to the current edition of the AS 2293.3 Standard.
LED Exit Maintenance:
Lamp Replacement:
•Use only the LED lamp strip recommended
on the label inside the Exit fitting or this
instruction.
•To replace the lamp, loosen the cover
screws and remove, unplug lamp
connector, remove nuts fastening lamp strip
and remove, replace and reassemble.
Battery Replacement:
•Use only the battery recommended on the
label inside the Exit fitting and on this
instruction.
•Un-plug the lead from the Inverter pack.
Remove the old battery and install the new
one.
•Reconnect the battery cable to the inverter
pack.
Trouble Shooting:
Below are a list of common problems and their
possible causes.
Fault: The Green LED Test Switch
indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected
Test Switch for damage.
Fault: Lamp does not illuminate in
emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault: Lamp illuminates in emergency
mode, but only stays on for a short
period.
Check: Battery has been allowed to charge for
at least 24 hours.
Battery for damage.
Rated Emergency Lumen Output in accordance with AS2293.1 (refer to
spacing tables for installation positions):
C0=D6.3 C90=E3.2
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The battery in this fitting has been selected to give excellent long life performance
in a controlled AS2293 testing environment. Excessive battery cycling will reduce through-life performance
and may lead to premature battery failure. Battery warranty claims, as a result of such abuse, are
specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
http://clevertronics.com.au/terms-conditions-sale-australia-nz/
L10™ Jumbo LED Exit
Installation & Maintenance Instruction Leaflet
Designed in Australia to comply with the
requirements of AS2293.3: 2005 and AS/NZS
CISPR15: 2011.
NOTE: Standard product codes with this symbol are
enabled with Clevertest Plus capability. Please refer to
the operation guide supplied with the product for details.
Victoria (Head Office & Manufacturing)
195 Chesterville Rd
Moorabbin VIC 3189
Phone: [phone]
Fax: [phone]
News South Wales
Phone: [phone]
Fax: [phone]
Queensland
Phone: [phone]
Fax: [phone]
South Australia/Northern Territory
Phone: [phone]
Fax: [phone]
Western Australia
Phone: [phone]
Fax: [phone]
New Zealand
Phone: [phone]
Models: LJELED-40-xx
Testing:
Manual Test
xx = Blank
Zoneworks
xx = ZW
Zoneworks DATA
xx = DATA
DALI Compatible
xx = DALI
Clevertest
xx = CT
(
NOTE:-CT Products supplied with the Clevertest Plus Symbol
are
activated
with Clevertest PLUS capability. Please
refer to the operation
guide supplied with the product for
details).
Spare Parts:
1530010
BATTERY:L10 3.3V 2.5AH. 200mm lead.Brkt
8002470
PCA: Duris E5 Strip for LJELED.CT10050-D1
LJELED-40-CKIT-110
Jumbo LED Exit, Control Kit, L10
Important:
It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant Australian and International Standards.

1947245 V1.5 10 October 2017
Installation:
The Jumbo LED Exit can be Wall or Ceiling Mounted:
Wall Mounting (single sided)
•Remove one of the corner trim pieces
•Remove the back mounting plate.
•Determine power entry
•Position the mounting plate in the mounting position.
•Mark the 4 holes for mounting. Then install the appropriate fixings (not supplied).
•Reinstall the mounting plate to the fitting.
•Install the fitting on the mounting hardware, while routing the power cable through the access hole.
•Ensure connection of the grounding strap between the fitting and the back plate.
•Connect the 240VAC supply to the terminal block.
Ceiling Mounting (single or double sided)
•Remove one of the corner trim panels.
•Remove the diffuser panel.
•If converting to double-sided, remove the earth strap from the back plate before removing it.
•Determine power entry
•Position the fitting in the mounting position.
•Mark the mounting holes at the top of the fitting.
•Then install using the appropriate fixings (not supplied).
•Position the fitting while routing the power cable and attach to the surface as required.
•Connect the 240VAC supply to the terminal board.
If the CTP capabilities are activated please affix the CTP status Label to a visible surface.
Networking:
When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the
relevant Smart Node PCA.
Images and Dimensions:
Wall Mounting Plate
Ceiling Mounting Plate
Clevertronics Clevertest and Clevertest Plus
Refer to the supplementary operation guide supplied with the Product.
Zoneworks and DATA Monitored Options
Exits with part numbers LJELED*-ZW, LJELED*-DATA are fitted with Zoneworks communications
modules (nodes).These fittings are monitored using either Powerline Carrier Technology that utilising the
power cable to provide data communication or a dedicated data cable to/from data routers installed on a
dedicated data trunk connected to a central Server (can also be connected via Ethernet/Internet/Fibre).
Zoneworks software on the server is used to monitor, coordinate testing and collate test data from each
Exit. Zoneworks Exit can be commissioned by a single push of the test switch, or scanning of the supplied
barcode. The LED Test Switch indicator provides a multifunction indication of the status of the fittingduring
testing and normal operation:
State LED Operation
Commissioned
LED on Solid (Green)
Un-commissioned LED flashes at 0.5Hz (0.5s Green, 0.5s Yellow)
Emergency Light Test In Progress LED flashes at 3s On (Yellow) & 0.5s Off
In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to
the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of
a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA
version)
DALI EM Option
Exits with part numbers LJELED-DALI are fitted with DALI modules (nodes) that facilitate connection and
integration to 3rd Party Lighting Control Systems. Before installing the LJELED*-DALI please confirm that
the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The LJELED-
DALI will be addressed and configured into the control system by the Lighting Control System
Commissioning Technicians and not Clevertronics.
State LED Operation
Commissioned/ Un-commissioned LED on Solid (Green)
Emergency Light Test in progress LED flashes at 1s On (Yellow) & 1s Off
“IDENTIFY COMMAND”
Fitting goes into emergency mode for 10 seconds
A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network. DALI
connections are marked as Da Da.
Power Access
Mounting Holes
Power Access
Mounting Holes