Clinton STM-10GF User manual
Models STM-10GF and STM-20GF Multi Electrode DC Spark Testers
Instruction Manual
Clinton Instrument Company
295 East Main Street
Clinton, CT 06413 USA
Telephone: 860.669.7548 Fax: 860.669.3825
www.clintoninstrument.com
Rev C 11/10
Table of Contents
STM-10/20GF Instruction Manual - Page 1
Models STM-10/20GF DC Spark Testers
Safety
Safety Symbols
Environmental Conditions
Page 2 - STM-10/20GF Instruction Manual
Models STM-10/20GF DC Spark Testers
Introduction
STM-10/20GF Instruction Manual - Page 3
Models STM-10/20GF DC Spark Testers
Installation
Site Preparation
Select a suitable location for control unit and high voltage
test module
Page 4 - STM-10/20GF Instruction Manual
Models STM-10/20GF DC Spark Testers
To mount the control unit or high voltage test module on a
Clinton oor stand
Wiring Requirements
STM-10/20GF Instruction Manual - Page 5
Models STM-10/20GF DC Spark Testers
Page 6 - STM-10/20GF Instruction Manual
Models STM-10/20GF DC Spark Testers
Install mains power.
STM-10/20GF Instruction Manual - Page 7
Models STM-10/20GF DC Spark Testers
Page 8 - STM-10/20GF Instruction Manual
Models STM-10/20GF DC Spark Testers
STM-10/20GF Instruction Manual - Page 9
Models STM-10/20GF DC Spark Testers
Set DIP Switch SW1
.
Page 10 - STM-10/20GF Instruction Manual
Models STM-10/20GF DC Spark Testers
STM-10/20GF Instruction Manual - Page 11
Models STM-10/20GF DC Spark Testers
Prepare your product
In sure that the product to be tested is dry as it enters the
spark test electrode.
Ground the product conductor(s).
Center the product in the entrance of the safety guard.
Final Checklist
Page 12 - STM-10/20GF Instruction Manual
Models STM-10/20GF DC Spark Testers
Operation
Front Panel Controls
STM-10/20GF Instruction Manual - Page 13
Models STM-10/20GF DC Spark Testers
High Voltage Test Module
NOTE: An ST- 10G01 High Voltage Test Module is ST- 20G01 High
Voltage Test Module must be used with an STM-20GF control unit. High Voltage Test Modules are NOT inter-
changeable.
Page 14 - STM-10/20GF Instruction Manual
Models STM-10/20GF DC Spark Testers
Testing Your Product
STM-10/20GF Instruction Manual - Page 15
Models STM-10/20GF DC Spark Testers
Modes of Operation
The spark tester will operate in accordance with the DIP switch settings selected during “Installation.”
Page 16 - STM-10/20GF Instruction Manual
Models STM-10/20GF DC Spark Testers
J303 Subminiature Connector Pin Functions
Figure 9. J303
This manual suits for next models
1
Table of contents
Other Clinton Test Equipment manuals
Popular Test Equipment manuals by other brands
SignalFire
SignalFire Nodechecker-X Interface manual
Kyoritsu Electrical Instruments Works, Ltd.
Kyoritsu Electrical Instruments Works, Ltd. KEW3121B instruction manual
EL-CELL
EL-CELL PAT-Tester-x-8 user manual
U-Reach
U-Reach Intelligent U3 user manual
Byte Brothers
Byte Brothers rwc1000 user guide
Flo-tech
Flo-tech FT555F manual
