CLS JADE COLOUR FLOW TUNABLE WHITE User manual

www.cls-led.com www.cls-led.com
Ceiling 350º 50.000 h IP20
30 Watt
Max.
340º 23º 45º 69º 100 - 240
VAC
DRIVER
INCLUDED
DRIVER
INTERNAL
780 gram
DMX
512
RGB-W 1800K-
4000K
2700K-
5700K
CLS
DYNAMIC
COLOUR
COB
2
CLS JADE COLOUR FLOW - TUNABLE WHITE
Manual V1.2 - March 2019
INDEX
CONTENT
SAFETY INFORMATION
Ambiance
Max. 40º
Block access
below the work
area when
maintaining
the unit
Use a source
of AC power
that complies to
local electrical
codes
Disconnect the
power supply
before installing
or maintaining
Don’t install in
a flammable
or explosive
area
Warning!
Some surfaces
can be hot
Do not stare
into the LED
Don’t modify
or install
genuine parts
on this product
Qualified
technician
Make sure all
connectors are
connected
properly
Ceiling 350º 50.000h IP20
30Watt
Max.
340º 23º 45º 69º 100- 240
VAC
DRIVER
INCLUDED
DRIVER
INTERNAL
780gram
DMX
512
RGB-W 1800K-
4000K
2700K-
5700K
CLS
DYNAMIC
COLOUR
COB
CLS JADE COLOUR FLOW
Index 2
Safety information 2
Content 2
Technical 3
Specifications 3
Installation Global 4
Installation Eutrac 5
Programming 6
Factory setting table 6
Programming table 7
Barndoor assembly 8
Snoot / half snoot assembly 9
Honey comb assembly 10
Accessories 11
Accessory combinations 11
List of symbols 12

www.cls-led.com www.cls-led.com
3 4
75 mm Ø 100 mm
46 mm
84 mm
EUTRAC
Eutrac adapter
110 mm
122,5 mm157,7 mm
Tools
TECHNICAL
SPECIFICATIONS
LED: CLS Dynamic Colour CoB
Colour changing: RGB-W
Tunable White: 1800-4000K & 2700K-5700K
Beam angle: 23º, 45º or 69º
Power supply: 100 ~ 240 VAC
Power consumption: Max. 30 Watt (1450 lumen)
Housing: Black, grey or white PC (PC-ABS V0)
Heatsink black, grey or white coated aluminium
Weight: 780 gram
IP value: IP20
Measurements: 157,7 x 100 x 100 mm (hxwxd)
Ambient temperature: -10º C till +40º C
2018 CLS-LED BV. All rights reserved. Information subject
to change without notice, CLS-LED BV and all aliated
companies disclaim liability for injury, damage direct or
indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance
on the information contained in this manual. No part of this
manual may be reproduced, in any form or by any means,
without permission in writing from CLS-LED BV. Other legal
information can be found in our General conditions, found
on the back of your CLS-LED BV invoice, inside the CLS
catalogue or on our website
www.cls-led.com/General-Terms.pdf
3
1
# Y108052
# Y108062
5
4
2
CLS Global
3-phase rail + data
Set the adapter
to the desired phase
by turning the wheel
Position
indicator
340º
INSTALLATION
WITH GLOBAL ADAPTER

www.cls-led.com www.cls-led.com
65
2a
2b
1
CLS Eutrac
3-phase rail
+ data
3
5
# Y108152
90°- 0 - 90°
B
A
90°- 0 - 90°
B
4
# Y108155
Position
indicator
340º
INSTALLATION
WITH EUTRAC ADAPTER
PROGRAMMING
123
* If the LEDs ashes 10 times, something went wrong. Please try again. If the problem continues to occur, please contact your local sales distributor.
After 2 seconds
the LED will ash
3 times
conrming
storage*
Place magnet
at the bottom
of the Jade.
The LED will
light up
FACTORY SETTING TABLE
All settings can be configured via DMX. Settings can be configured at once or separately. When one or a couple settings needs to be
changed just leave all other setting values zero. This keeps those settings unchanged. Please check the table for more information.
Always use a DMX controller with digital interface. If not available, you can purchase the CLS D-ta DMX addresser unit ( #122200 ).
First make sure to set the DATA on the DMX controller. To program the setting into the LED fixture follow the next steps.
Max. 20 pieces of Jade Colour Flow per DMX line on a rail.
Max. 20 pieces of Jade Colour Flow can be connected in a group.

www.cls-led.com www.cls-led.com
7 8
1
4
3
6
disassembly
Accessory holder
Barndoor
Removing the barndoor: rotate the accessory
holder fully to the right or left, until you are
not able to rotate it any further.
Verwijderen van de barndoor: draai de
accessoire houder geheel naar links of naar
rechts tot deze niet meer verder kan.
If you want to rotate the barndoor to find the desired position,
you need to keep the accessory holder with one hand on its place.
If you don’t do this you might release the accessory holder!
Als u de barndoor wilt roteren voor een juiste positie, dient u
dit met 1 hand te doen en met de andere hand de accessoire
houder op zijn plaats te houden.
Doet u dit niet, dan kunt u de accessoire houder losklikken!
When you feel the resistance, pull the accessory
holder out of the mountingslot.
U voelt een weerstand en kunt nu de accessoire
houder naar voren halen.
Plaats de accessoire houder met de 4 klikvingers in
het midden van de montage gleuf op de Jade.
Place the accessory holder with the 4 click fingers
in the middle of the mounting slot on the Jade.
NL
UK Push firmly until you hear a clear‘Click’ sound.
Druk krachtig aan,u dient een duidelijke
‘klik’ te horen.
2
5
BARNDOOR ASSEMBLY

PROGRAMMINGTABLE
DMXFunctionDataParametersDescription
CH1 Setaddress
001to255
0
0=nochange
UsethisDMXchanneltosetaddressfrom001to
255.TheconfiguredDMXaddressiscalled“n”
1…255DMXaddress=1…255
CH2 Setaddress
256to508
0
nochange
UsethisDMXchanneltosetaddressfrom256to
508.TheconfiguredDMXaddressiscalled“n”
1…255DMXaddress=256…508
CH3 Static
behavior
0 nochange
IfnoDMXispresentthefixturewillrespondlike
setinthisfunction.
1 lastDMXvalue
2 outputoff
3 loadstaticvalues
CH4 Softdim
0 nochangeSoftdimwillinterpolatebetweentheDMX
values.Thisfunctionmakesthedimcurve
smoother
1 off
2
on
CH5 Master
control
0 nochange Ifmasterisfirstchannelisselectedthechannel
willbeDMXchannel“n”.Ifmasterislastchannel
isselectedthechannelwillbe“n+x”
(“x”iscalculatedintheoutputpatch).
1 nomasterused
2 masterisfirstchannel
3
masterislastchannel
CH6 Output1
patch
0
nochange
Eachoutputchannelcanbepatchedtorespond
tothedesiredDMXchannel.Thisenablesthe
usertomixupthecoloursaccordingtothe
controllerthatisused.

Example:alloutputsarepatchedas1
AlloutputswillbecontrolledbyDMXchannel
“n”.IfmasterisusedtotalDMXchannelswillbe2
otherwiseituses1channel(“x”=1).

Example:output1&2arepatchedas1and3&4
arepatchedas2
Output1&2willbecontrolledbyDMXchannel
“n”.
Output3&4willbecontrolledbyDMXchannel
“n+1”.
IfmasterisusedtotalDMXchannelswillbe3
otherwiseituses2channels(“x”=2).


1 DMXchanneln
2 DMXchanneln+1
3 DMXchanneln+2
4 DMXchanneln+3
CH7Output2
patch
0 nochange
1
DMXchanneln
2 DMXchanneln+1
3 DMXchanneln+2
4 DMXchanneln+3
CH8 Output3
patch
0 nochange
1 DMXchanneln
2 DMXchanneln+1
3 DMXchanneln+2
4
DMXchanneln+3
CH9Output4
patch
0 nochange
1 DMXchanneln
2 DMXchanneln+1
3
DMXchanneln+2
4 DMXchanneln+3
CH10Staticoutput
1
0 nochangeEachoutputchannelcanbesettoanstatic
intensity.

IfnoDMXispresentandStaticbehaviorissetto
“loadstaticvalues”.Theoutputswillbesettothe
configuredintensityvalues.






1
outputoff
2…255intensity2…255
CH11Staticoutput
2
0 nochange
1 outputoff
2…255intensity2…255
CH12Staticoutput
3
0 nochange
1 outputoff
2…255
intensity2…255
CH13Staticoutput
4
0 nochange
1 outputoff
2…255intensity2…255
CH14Loaddefault
settings
0
nochange
ThisfunctionresetsallsettingstotheFactory
setting.CheckFactorysettingtable.
X LoadFactorysettings.Xisrow
numberfactorysettingtable.

PROGRAMMING TABLE

www.cls-led.com www.cls-led.com
9 10
SNOOT / HALF SNOOT ASSEMBLY
1
5
4
2
3
6
disassembly
Accessory holder
Snoot
Removing the snoot: rotate the accessory holder
fully to the right or left, until you are not able to rotate
it any further. (See step 5)
When you feel the resistance, pull the
accessory holder out of the mountingslot.
HONEY COMB LOUVRE ASSEMBLY
1
5
4
2
3
6
disassembly
Accessory holder
Honey Comb Louvre
Removing the honey comb: rotate the accessory holder
fully to the right or left, until you are not able to rotate
it any further. (See step 5)
When you feel the resistance, pull the
accessory holder out of the mountingslot.
Facing towards
the Jade

www.cls-led.com www.cls-led.com
11 12
ACCESSORIES
ACCESSORIES
Global - black
Y108501-B CLS Global 3-phase rail + data 1 meter black
Y108502-B CLS Global 3-phase rail + data 2 meter black
Y108503-B CLS Global 3-phase rail + data 3 meter black
Y108504-B CLS Global 3-phase rail + data 4 meter black
Y108511-B CLS Global 3-phase rail + data end feed right, black
Y108512-B CLS Global 3-phase rail + data end feed left, black
Y108513-B CLS Global 3-phase rail + data middle feed black
Y108515-B CLS Global 3-phase rail + data L-coupler inner black
Y108516-B CLS Global 3-phase rail + data L-coupler outer black
Y110938 CLS Global 3-phase rail + data end cap black
Eutrac - black
Y108112 CLS Eutrac 3-phase rail + data 1 meter black
Y108122 CLS Eutrac 3-phase rail + data 2 meter black
Y108132 CLS Eutrac 3-phase rail + data 3 meter black
Y108142 CLS Eutrac 3-phase rail + data 4 meter black
Y108152 CLS Eutrac 3-phase rail + data end feed right, black
Y108155 CLS Eutrac 3-phase rail + data end feed left, black
Y108158 CLS Eutrac 3-phase rail + data middle feed black
Y108162 CLS Eutrac 3-phase rail + data end cap black
Y108175 CLS Eutrac 3-phase rail + data L-coupler inner black
Y108178 CLS Eutrac 3-phase rail + data flex coupler black
Y108199 CLS Eutrac 3-phase + data monopoint black
ACCESSORIES
Eutrac - white
Y108133 CLS Eutrac 3-phase rail + data 3 meter white
Y108153 CLS Eutrac 3-phase rail + data end feed right, white
Y108163 CLS Eutrac 3-phase rail + data end cap white
122200 CLS D-Ta DMX tester/addresser unit
Y106016 CLS Magnet pin (4 pcs)
Y106200-B CLS Jade Expo Snoot, black
Y106200-W CLS Jade Expo Snoot, white (black inside)
Y106201-B CLS Jade Expo Half Snoot, black
Y106201-W CLS Jade Expo Half Snoot, white (black inside)
Y106202-B CLS Jade Expo Barndoor, black
Y106202-W CLS Jade Expo Barndoor, white (black inside)
Y106215 CLS Jade Expo Honey Comb louvre
Global - grey
Y108501-G CLS Global 3-phase rail + data 1 meter grey
Y108502-G CLS Global 3-phase rail + data 2 meter grey
Y108503-G CLS Global 3-phase rail + data 3 meter grey
Y108504-G CLS Global 3-phase rail + data 4 meter grey
Y108511-G CLS Global 3-phase rail + data end feed right, grey
Y108512-G CLS Global 3-phase rail + data end feed left, grey
Y108513-G CLS Global 3-phase rail + data middle feed grey
Y108515-G CLS Global 3-phase rail + data L-coupler inner grey
Y108516-G CLS Global 3-phase rail + data L-coupler outer grey
Y110935 CLS Global 3-phase rail + data end cap grey
Accessory Combinations
LIST OF SYMBOLS
Multiple connection
Daisychain connectivity
Installation depth
In centimeters
Swivel
Fixture is horizontally rotatable,
indicated in degrees
Swivel
Fixture is vertically rotatable,
indicated in degrees
Installation size
In centimeters
Application area
Indoor or outdoor
Application area
Floor, wall or ceiling
Protection class
One, two or three
Cable length
Maximum cable attached
to the fixture in centimeters
Lifespan
Of the light source in hours
Driver
Inclusive or exclusive
Internal or external
Pressure
Maximum pressure on the
fixture in kg/cm2
Weight
In grams/kilograms
Curve
Minimal bending curve
in centimeters
LED pitch
Pitch between the LEDs
in millimeters
Power supply
In VDC, VAC or milliAmpere
Power consumption
In VA or Watt
IP value
Ingress Protection classifies the
degrees of protection provided against
the intrusion of the product
Cutting length
Indicated by the cutting
marks
LEDs
Kind of LED used in the
fixture
Lenses
Availble lenses,
indicated in degrees
Performance Zoom
Adjustable beam angle
Plug & play
Easy connection using the
SmartConnect system
White colour temperature
In dierent Kelvin values;
Cold white, neutral white, warm
white or extra warm white
Colour
Available colours;
Amber, blue, red or green
Colour changing
RGB, RGB-W, RGB-A,
AWB or Tunable White
DMX input
Fixture works on DMX512
protocol
Magno dimming
Accurate dimming from
100 - 1% by using a magnet
Dynamic Control
Dynamic Power Control or
Dynamic Temperature Control
Combined product
Compose your own fixture
Warranty
3 or 5 years warranty on
the product
Energy label
Conformité Européenne
CE marking for free marketability
of industrial goods within the EU
r
h
ø w d
Dimmable
1-10 Volt, Phase, individual,
DMX dimmable or DALI
DRIVER
INCLUDED
DRIVER
EXTERNAL
Retail & Food LED modules
Clothing, furniture, kitchens, jewellery,
shoes, bread, meat, fish and
vegetables & fruit.
Lightsource
Equipped with a CLS, Citizen or a Xicato
LED module
Bluetooth controlled
By Casambi
PWM dimming
Traditional PWM dimming, DMX analog
or DMX Hybrid dim
CLS
DYNAMIC
COLOUR
COB