manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. CMD
  6. •
  7. Industrial Equipment
  8. •
  9. CMD 23 Series User manual

CMD 23 Series User manual

‘CLICK’
23 series (slab boxes) Installation, user and care guide
Part No: 134251 Issue No: 001
1 compartment slab box
3 compartment slab box
2 compartment slab box
4 compartment slab box
Clean the location for
the slab box ensuring
the area is free from
dust and debris.
Apply a suitable
adhesive xing method
to the base of the slab
box.
Position the box in the
desired location and
follow steps provided by
adhesive manufacturer.
Remove the required
knockouts and attach a
suitable conduit. Feed
wires into the box.
Swivel the retractable
xing brackets out on
the base of the slab box.
Position plates in desired
orientation and x in
place with 2x taptite
screws.
Mark and drill the xing
positions in the desired
location.
The box is ready to
connect to power.
Screw the slab box to
the oor substrate with
2x suitable screws at the
points shown.
Earthing the box and sockets
Installing accessory plates (if applicable)
Slab box xing methods
Adhesive xing (optional)
Screw xing with retractable xing brackets
Tap-off engagement/release
**WARNING**
An unterminated tap-off MUST NEVER be connected to a live track.
Provided that it is off load, a terminated tap-off may be removed/
inserted into a live track. Conduit must be bonded to Earth.
Align tap-off pins with
slots on socket. Push
down to engage.
Press down and push
backwards until button
clicks upwards to lock.
To remove, press button
to disengage. Push
forwards and lift up to
remove.
To reset after it has
tripped, press and hold
the grey reset button
until a click is heard.
The indicator will change
to show it is now active.
Remove your nger from
the reset button.
A qualied person
should test the SRCD
function periodically to
comply with standards.
A qualied or fully
competent person
should test the SRCD
before rst use.
When active, the SRCD
indicator window is
lled with a red marker.
When the SRCD trips,
the red marker in the
indicator window
recedes as shown.
Testing and resetting SRCD socket (if applicable)
‘CLICK’
Test
Reset
Indicator
up
Indicator
down
Active SRCD state Tripped SRCD state
Clean Earth (C/E) Low Noise
Standard Earth
The box base must be earthed with a suitable ring terminal to the integrated
earth stud. To ensure the sockets are earthed, a link will be required from
the box earth stud to the socket earth. On Clean Earth (C/E) Low Noise
installations these should be wired directly to the Clean Earth CPC (Circuit
Protective Conductor).
CMD Ltd, Rotherham, S65 1EN, UK
T: 01709 829 511 E: [email protected]
Additional information
• Incorrect use could lead to risk of electrocution.
• Product to be used only for the intended purpose of distributing power in a commercial environment.
• Installation is to be carried out in accordance with relevant Health & Safety regulations and only to be carried out by a skilled or competent person.
• The installation should be installed to comply with the relevant national standards and be inspected and tested prior to being put into service (in the UK
BS 7671 Wiring Regulations).
• Isolate the supply before installation or repositioning. Any locking mechanisms must be used and fully engaged.
• Do not misuse, dismantle or re-congure the product because doing so will invalidate the warranty.
• If a product incorporates RCD protection, the RCD should be regularly tested in-line with current standards.
Safety
• Refer to the Declaration of Conformity.
Standards
Further guidance
• Clean using a dry cloth. No abrasives or solvents to be used on the product.
• Do not drop or expose to moisture.
Product care
• If viewing this sheet prior to specication/technical documentation purposes, be aware of potential plug clashes with certain socket plate orientations.

This manual suits for next models

1

Other CMD Industrial Equipment manuals

CMD 20 Series Troubleshooting guide

CMD

CMD 20 Series Troubleshooting guide

CMD flexacier 9000 User manual

CMD

CMD flexacier 9000 User manual

CMD 90 Series User manual

CMD

CMD 90 Series User manual

CMD winflex DG User manual

CMD

CMD winflex DG User manual

CMD flexacier User manual

CMD

CMD flexacier User manual

CMD 22 Series User manual

CMD

CMD 22 Series User manual

Popular Industrial Equipment manuals by other brands

ABB +Q957 user manual

ABB

ABB +Q957 user manual

G.B.C BASIC EDGE 50 instruction manual

G.B.C

G.B.C BASIC EDGE 50 instruction manual

Tronair Batpak 11-6602-1000 Operation & service manual

Tronair

Tronair Batpak 11-6602-1000 Operation & service manual

Pilz PNOZ mi2p Operation manual

Pilz

Pilz PNOZ mi2p Operation manual

Clemco Zero BNP 6012 manual

Clemco

Clemco Zero BNP 6012 manual

Erskine Attachments V-Plow Operator's manual

Erskine Attachments

Erskine Attachments V-Plow Operator's manual

ABB HT610965 Operation manual

ABB

ABB HT610965 Operation manual

Morra MH 540 user manual

Morra

Morra MH 540 user manual

Eaton S090ST manual

Eaton

Eaton S090ST manual

GRIGGIO G 240 P4 instructions

GRIGGIO

GRIGGIO G 240 P4 instructions

Nexen AIR CHAMP HT45 user manual

Nexen

Nexen AIR CHAMP HT45 user manual

WTE V5 installation manual

WTE

WTE V5 installation manual

ABB HT845232 Operation manual

ABB

ABB HT845232 Operation manual

SMC Networks CJP Series Operation manual

SMC Networks

SMC Networks CJP Series Operation manual

JohnDow Industries JDI-AFT58 Operator's manual

JohnDow Industries

JohnDow Industries JDI-AFT58 Operator's manual

IMB MB9016A instruction manual

IMB

IMB MB9016A instruction manual

Clarke CUMB1 Assembly & operating instructions

Clarke

Clarke CUMB1 Assembly & operating instructions

amiad Arkal Spin Klin 2 user guide

amiad

amiad Arkal Spin Klin 2 user guide

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.