Coaster CALIFORNIA 203481KW User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
203481KW (B1 ~ B3)
CALIFORNIA KING SIZE BED
R
www.coastercompany.com
PAGE 1 OF 7 REVISION 0: 05/01/2014
REVISION 1: 05/15/2014

ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1 . Remove hardware from box and sort by size.
2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
Warning !
1 . Don't attempt to repair or modify parts that are broken or defective. Please contact the
store immediately.
2 . This product is for home use only and not intended for commercial establishment.
PARTS IDENTIFICATION
www.coastercompany.com
BED RAIL 2PCS
BED SLAT WITH 3 HOLES 3PCS
G
B1 (BOX 1)
AHEADBOARD PANEL 1PC
C
LEFT HEADBOARD LEG
1PC
PAGE 2 OF 7
B
RIGHT HEADBOARD LEG
1PC
F
R
DFOOTBOARD 1PC
ROLL SLAT (5PCS)
H
CENTER RAIL
I
2SETS
1PC
DRAWER BOTTOM
TRESTLE BAR 1PC
J
BED SLAT SUPPORT
WITH LEVELER
L
DRAWER BOTTOM
TRESTLE BAR SUPPORT
WITH LEVELER
M
3PCS
B2 (BOX 2)
B3 (BOX 3)
1PC
FOOTBOARD
DRAWER BOX
P2PCS
203481KW (B1)
HEADBOARD COMPLETE
*FROM BOX 1
HB
203481KW (B1)
FOOTBOARD
*FROM BOX 1
1PC
1PC
D
ECONCEAL PANEL 1PC
ITEM : 203481KW (B1 ~ B3)
BOTTOM CROSS BAR 2PCS
K
UPPER TRESTLE
SUPPORT BAR
N1PC
RAIL CAP
O2PCS

ASSEMBLY INSTRUCTIONS
HARDWARE IDENTIFICATION
www.coastercompany.com
1BOLT 6PCS
2ALLEN WRENCH 1PC
LOCK WASHER 6PCS
FLAT WASHER 6PCS
PAGE 3 OF 7
R
4
3
Z - B1 (BOX 1) Z - B2 (BOX 2)
HARDWARE PACK IS
LOCATED IN 203481KW (B1)
-HARDWARE PACK IS
LOCATED IN 203481KW (B2)
-
7
81PC
9SHORT FLAT
HEAD SCREW 7PCS
10 LONG FLAT
HEAD SCREW 36PCS
BIG ALLEN WRENCH
1PCSMALL ALLEN WRENCH
5SHORT BOLT 10PCS
6LONG BOLT 4PCS
11 LOCK WASHER 10PCS
FLAT WASHER 10PCS
12
7
81PC
9SHORT FLAT
HEAD SCREW
10 LONG FLAT
HEAD SCREW 36PCS
BIG ALLEN WRENCH
1PCSMALL ALLEN WRENCH
5SHORT BOLT 10PCS
6LONG BOLT 4PCS
11 LOCK WASHER 10PCS
FLAT WASHER 10PCS
12
ITEM : 203481KW (B1 ~ B3)
NOTE : PHILLIPS HEAD SCREW DRIVER IS REQUIRED IN THE ASSEMBLY
PROCESS.HOWEVER, MANUFACTURER DOES NOT PROVIDE THIS ITEM.

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
203481KW (B1) - BOX 1
PAGE 4 OF 7
R
203481KW (B1~B3) - BOX 1 TO BOX 3
STEP 2
STEP 1
"L" Marking behind the
Headboard & Leg
Headboard & Leg
"R" Marking behind the
A
C
B
2
1
3
4
STEP 2.1
D
F
F
F
8
HB
STEP 2.2 F
K
K
ITEM : 203481KW (B1 ~ B3)
10
Align and fasten left (B) and right (C) headboard leg to headboard panel (A) using bolt (1),
lock washer (3) and flat washer (4) and fully tighten with Allen wrench (2).
**Please take note the marking on the leg and headboard**
2.1 Loosen the bolt and align and fasten bed rail (F) to headboard (HB) and footboard (D) using the bolt
and fully tighten with big Allen wrench (8).
2.2 Align and fasten bottom cross bar (K) to bed rail (F) using long flat head screw (10) and tighten with
Phillips head screw driver (NOT INCLUDED).

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
PAGE 5 OF 7
R
STEP 3
STEP 4
'T' Runner
STEP 4.2
STEP 4.1
STEP 4.3
STEP 3.2
'T' Runner
'T' Runner
STEP 3.3
D
J
M
J
10
P
9D
F
J
P
M
M
JP
D
M
STEP 3.1
J
N
N
N
ITEM : 203481KW (B1 ~ B3)
3.1 Align and fasten drawer bottom trestle bar support with leveler (M) to upper trestle support
bar (N) and drawer bottom trestle bar (J) by turning clockwise until tight.
3.3 Turn the drawer glide (attached to footboard 'D') outward.
4.1 Slide and push the footboard drawer box (P) into place until it is fully and evenly closed.
NOTE : Pull the drawer box (P) out a little bit and make sure the drawer glide is center prior to
starting of assembly.
4.3 After completing the drawer alignment,adjust the leveler of the drawer bottom trestle bar support (M)
to touch the floor.
3.2 Align and fasten drawer bottom trestle bar (J) to 'U' bracket at bed rail (F) using long flat head
screw (10) and tighten with Phillips head screw driver (NOT INCLUDED).
4.2 Align and fasten the drawer glide to drawer bottom trestle bar (J) using short flat head screw (9)
and tighten with Phillips head screw driver (NOT INCLUDED).

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
PAGE 6 OF 7
R
STEP 5
STEP 6
STEP 6.2
STEP 6.3
9
E
D
D
STEP 5.1
G
IL
10
L
K
STEP 5.4
10
F
H
STEP 5.3
10 F
G
7
6
I
LLG
STEP 6.1
STEP 5.2
7
6
I
ITEM : 203481KW (B1 ~ B3)
5.1 Align and fasten bed slat with 3 holes (G) to center rail (I) and bed slat support with leveler (L) using
long bolt (6) and tighten with small Allen wrench (7).Adjust leveler to touch the floor.
5.2 Align and fasten center rail (I) to wood cleat at the footboard (D) using long bolt (6) and tighten with
small Allen wrench (7).
6.2 Place conceal panel (E) on top of roll slat (H) and footboard (D).
5.3 Align and fasten bed slat with 3 holes (G) to bed rails (F) using long flat head screw (10) and tighten with
Phillips head screw driver (NOT INCLUDED).
5.4 Align and fasten bottom cross bar (K) to bed slat support with leveler (L) using long flat head screw (10)
and tighten with Phillips head screw driver (NOT INCLUDED).
6.1 Align and fasten roll slat (H) to bed rails (F) using long flat head screw (10) and tighten with Phillips
head screw driver (NOT INCLUDED).
6.3 Align and fasten conceal panel (E) to wood cleat at the footboard using short flat head screw (9)
and tighten with Phillips head screw driver (NOT INCLUDED).

ASSEMBLY INSTRUCTIONS
www.coastercompany.com
PAGE 7 OF 7
R
11
12
5
7
O
F
STEP 7
ITEM : 203481KW (B1 ~ B3)
Align and fasten rail cap (O) to to bed rail (F) using short bolt (5),lock washer (11) and flat
washer (12) and tighten with small Allen wrench (7).