Cobra 602-2610B User manual

23801 E. La Palma Ave., Yorba Linda, CA 92887 Ph. 714.692.8180 Fax. [phone]
www.cobrausa-vtwin.com
04/20
*Cobra®recommends you always wear a helmet while riding. Please never operate your motorcycle while under
the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.
Items Supplied >
1 - Detachable (BA) Solo Rack with Latches
(Chrome or Black Finish)
2 - 3/8” I.D. Front Mounting Bushings
2 - 3/8” I.D. Rear Bushing Spacers
2 - 3/8” I.D. Rear Bushing Sleeves
2 - 3/8” I.D. Rear Bushings
4 - 3/8”-16 x 1-3/4” Button Head Bolts Zinc
Application(s) >
HARLEY:
SOFTAIL: FLSL 2018 - 2019
FXBB 2018 - 2019
(ONLY ABOVE MODELS AS OF JAN 2020 WITH STOCK
SOLO SEAT. WILL NOT WORK WITH PASSENGER SEAT
INSTALLED. SEE OTHER COBRA B.A. RACKS FOR
SADDELMAN STYLE STEP-UP SEAT FITMENT)
Instruction Manual >
Read all instructions carefully before installing your new Cobra®product!
1. Remove the front bolt from the right-side fender rail and discard. NOTE: Remove one side only so the
fender does not fall resulting in possible scratches or damage to the fender or paint. See FIGURE 1.
2. Install the front mounting bushing into the front hole using the supplied 3/8”-16 x 1-3/4” long button
head bolt. Apply sufficient blue Loctite to the bolt threads and tighten bolt securely. See FIGURE 3.
3. Remove the right rear fender rail bolt and discard. See FIGURE 1.
4. Assemble the supplied plastic bushing over the sleeve as shown in FIGURE 2. Make sure the
chamfered inner edge goes towards the wide end of the sleeve.
5. Install the rear bushing assembly as oriented in FIGURE 3, using the supplied 3/8”-16 x 1-3/4” long
button head bolt. Apply sufficient blue Loctite to the bolt threads and tighten bolt securely.
602-2610 / 602-2610B
Page 1 of 3
DOCUMENT NO. 0017 REV. B
CONTINUED ON PAGE 2
FIGURE 1
REMOVE STOCK
FRONT BOLT
REMOVE STOCK
REAR BOLT

23801 E. La Palma Ave., Yorba Linda, CA 92887 Ph. 714.692.8180 Fax. [phone]
www.cobrausa-vtwin.com
04/20
Instruction Manual >
602-2610 / 602-2610B
Page 2 of 3
4.
5.
6. Repeat Steps 1-5 on the left side.
7. Install the detachable rack onto the motorcycle by first inserting the front portions of the side plates on
to the front mounting bushings on the frame rails. Make sure the rack is seated all the way onto the
mounting bushings. See FIGURE 4.
8. Then slowly rotate the rack downward so the rear portions of the side plates slip over the rear
mounting bushings. See FIGURE 4.
DOCUMENT NO. 0018 REV. A
CONTINUED ON PAGE 3
FIGURE 2
REAR
BUSHING
SPACER
3/8-16 X 1-3/4”
BUTTONHEAD
REAR
BUSHING
SLEEVE
CHAMFERED
INNER EDGE
FIGURE 3
FRONT
MOUNTING
BUSHING
REAR MOUNTING
BUSHING
FIGURE 4
REAR MOUNTING
BUSHING
DETACHABLE
LATCH KNOB
DETACHABLE
LATCH PIN
FRONT MOUNTING
BUSHING
REAR BUSHING

23801 E. La Palma Ave., Yorba Linda, CA 92887 Ph. 714.692.8180 Fax. [phone]
www.cobrausa-vtwin.com
04/20
Instruction Manual >
602-2610 / 602-2610B
Page 3 of 3
9. Pull backward on both detachable latch knobs and then push downward on the rack to allow the rack
to sit completely on the rear mounting bushings. Then release the detachable latch knob to fully
engage the latch pin underneath the mounting kit bushing. See FIGURE 5.
10. Always check to make sure both detachable latch pins are fully engaged on the bottom of the
mounting kit bushing. See FIGURE 5.
11. Before each ride, check to make sure the detachable latches are fully engaged underneath the
mounting bushings.
12. Check the tightness of all the screws after the first ride, after the first 500 miles, and at every engine
service thereafter.
DOCUMENT NO. 0018 REV. A
To clean your black accessory use a liquid based soap detergent, such as dishwashing soap applied with a soft cloth and
rinse with clean water. Note: Avoid abrasive cleaning methods such as granular or dry cleansers, simple green, Scotch-
Brite or steel wool pads. Abrasives may breach the coating and shorten life.
FIGURE 5
MAKE
SURE
LATCH PIN
IS FULLY
ENGAGED
UNDER
BUSHING