Cochlear Baha 4 Assembly instructions

Fitting Guide
Roger and Cochlear™ Baha® Sound Processors
This guide provides detailed information on how Roger X should be used with Cochlear™ Baha® Sound Processors Generation and
Generation 4 to achieve the best possible performance.
Set-up
The table below shows what is required to connect a Cochlear Baha sound processor to a Roger X receiver.
Product name
Cochlear Baha sound processor
(picture shows Cochlear Baha® 4 Sound Processor Baha® BP100 sound processor)


Roger X
Receiver
Pre-fitting for Baha® 3 Sound Processors
For the Baha BP100 and BahaBP110 sound processors no pre-fitting is required.
The DAI program is already pre-defined as program number “3”.
Just plug the Roger X into the sound processor and select program number “3” on the Baha.

Fitting Guide |
Roger and Cochlear™ Baha® Sound Processors 2
Pre-fitting for Baha® 4 Sound Processor
Launch the Cochlear Baha® Fitting Software 4.0 SR1, enter the Fine Tuning screen and activate the DAI + Mic program for the Baha 4
Sound Processors.
1. Select “DAI + Mic” on a program slot of your choice.
2. Ensure, the “Mic relative DAI / Telecoil (dB)” is set to 0
dB
. Save
Cochlear Baha ® Fitting Software 4.0 SR1 (4.0.0.51 2)
Connect
Hold the Roger inspiro microphone close to Roger X (within 10
cm 4 inches) and press the Connect button.
Your patient should now report that he she has heard the
confirmation beeps (a low tone followed by a high tone).
If your patient didn’t hear the confirmation beeps, you may need to
switch the processor into the DAI program.
Repeat this connect process until your patient hears the beeps.

Fitting Guide |
Roger and Cochlear™ Baha® Sound Processors 3
Getting started
1. Turn all equipment off.
2. Plug the Roger X into the Baha sound processor.
3. Switch on the Baha sound processor.
4. Select the dedicated “DAI + Mic” program, the output of the
Roger X is mixed with the signal of the Baha microphones.
5. Test the patient’s speech recognition in quiet at normal
sensitivity with the Baha sound processor alone and then through
the Roger system only (out of range of the processor microphone).
Performance should be similar between these two conditions.
If the Roger signal is too loud or too soft, the Roger inspiro may be
required to optimize the Roger volume level on the Roger X.
1
1
Available for Roger X (02) only
Using Roger via the -Coil
Alternatively, the receiver Roger MyLink can be used after plugging
in the Baha Telecoil to the Europin Direct Audio Input (DAI) on the
Baha sound processor.
Pre-fitting for Baha® 4 Sound Processor when used with Roger MyLink
1. Activate the “Telecoil + Mic”program
2. Ensure, the “Mic relative DAI / Telecoil (dB)” is set
to 0 dB
. Save
Cochlear Baha® Fitting Software 4.0 SR1 (4.0.0.5132)

Fitting Guide |
Roger and Cochlear™ Baha® Sound Processors 4
roubleshooting
Signal from Roger microphone cannot be heard
Roger X is not connected to the Roger microphone
Roger microphone is not switched on or is muted
Baha user is out of range of the Roger microphone
Batteries not suitable
Connect Roger X with the Roger microphone
Switch on the Roger microphone and make sure it is not muted
(refer to User Guide)
The Baha user has to move closer to the Roger microphone to be
within its operating range
Please use dedicated high power batteries (e.g. 4hole Rayovac) or
rechargeable batteries
Sound Processor microphones are attenuated
Microphone sensitivity Make sure microphone sensitivity has not been reduced in the DAI
program
The Roger microphone’s signal suffers from interruptions
The Roger microphone is too far away or shielded by obstacles
(e.g. human body)
Reduce the distance between Roger X and the Roger microphone,
and ensure both devices are in line of sight
Listening check
Product name
MLx Audio Checker and Roger X

Roger X plugged directly into the MLx Audio Checker
Adapter / Roger receiver
Special features for educational system
2
Programming of EasyGain
If the volume of the Roger system is not satisfactory, you can
change the gain of the receiver via Roger inspiro. Hold Roger
inspiro close to Roger X (less than 10 cm 4 inches) and press Check.
Roger X information will appear on the inspiro’s screen.
Press Manage, scroll with the cursor to EasyGain and press OK.
Now you can change the gain of the receiver in the range of
-8 to +8 dB.
2
Available for Roger X (02) only
V1.00 201
4-11 © Phonak AG All rights reserved