Cochlear Nucleus CP810 User manual

Nucleus®CP810 Sound Processor
User Guide
Front and back cover CP810 Iss3 01.indd 3 13/05/2009 4:56:21 PM

Note
Important information oradvice.Can save
inconvenience.
Tip
Time saving hint orsavesinconvenience.
Caution (no harm)
Special care to be taken to ensure safety
and effectiveness.
Could cause damage to equipment.
W arning (harmful)
Potential safety hazardsand serious
adverse reactions.
Could cause harm to person.
Symbols
195992 Iss3 CP810 user guide 01.indd 2 13/05/2009 4:23:08 PM

Contents
Introduction....................................................................................................... 7
Purpose of this guide ................................................................................. 7
The Cochlear
Nucleus CP810 Sound Processor.................................... 7
Getting to know your processor....................................................................9
Processing unit ............................................................................................9
Earhook.......................................................................................................10
Battery module.........................................................................................10
Coil and coil cable .....................................................................................11
Coil magnet ............................................................................................... 12
M icrophone protectors ........................................................................... 12
Processor options .................................................................................... 13
Wearing your processor ................................................................................ 15
Placing your processor on your ear....................................................... 15
Attaching the coil and coil cable........................................................... 16
Attaching the coil cable to the coil................................................. 16
Attaching the coil to the processing unit....................................... 16
A secure and comfortable fit...................................................................17
Changing the earhook ............................................................................18
Adjusting and replacing the coil magnet .............................................18
Adjusting magnet depth.................................................................... 19
Changing magnet strength............................................................... 19
Changing the coil cable ...........................................................................20
Using the Snugfit™for a secure fit........................................................22
Attaching and removing the Snugfit ..............................................23
Changing the w ay you w ear your processor .......................................24
Locking and unlocking the battery module .......................................24
Locking and unlocking the tamper resistant battery cover..............25
Identifying your processors ....................................................................26
Detaching and attaching the battery module .........................................27
Detaching the battery module from the processing unit................. 27
195992 Iss3 CP810 user guide 01.indd 3 13/05/2009 4:23:08 PM

Attaching the battery module to the processing unit ......................28
Using your processor......................................................................................29
Turning your processor on and off ........................................................29
Changing programs ..................................................................................29
Understanding indicator lights.............................................................. 30
Understanding private tones..................................................................32
Using the telecoil......................................................................................33
Using Auto Telecoil.............................................................................33
Using the telephone with your processor............................................34
Changing loudness of sounds.................................................................34
Controlling microphone sensitivity.................................................35
Controlling microphone volume......................................................35
Locking and unlocking processor buttons ...........................................36
Advanced user interface..........................................................................36
Checking the coil ......................................................................................37
Replacing and recharging batteries ............................................................39
Replacing disposable batteries ..............................................................39
Recharging the rechargeable battery module..................................... 41
Understanding battery charger indicator lights ...........................43
General warnings and precautions for handling batteries and the
battery charger..........................................................................................43
Batteries ...............................................................................................43
Battery charger ...................................................................................45
Using audio accessories with your processor............................................47
Connecting and disconnecting audio accessories..............................50
Changing from an audio accessory to microphones ..................52
Changing from microphones to audio accessory.........................52
General warnings and precautions for the use of
audio accessories......................................................................................52
Using sound processor covers......................................................................53
Attaching sound processor covers ........................................................53
195992 Iss3 CP810 user guide 01.indd 4 13/05/2009 4:23:08 PM

Removing sound processor covers........................................................54
Caring for your processor..............................................................................55
Wearing your processor in cold or hot temperatures .......................55
Protecting your processor from dust and water damage.................55
Drying your processor .............................................................................56
Cleaning your processor parts ...............................................................57
Replacing microphone protectors ........................................................58
Cleaning the battery charger .................................................................58
Storing your processor when not in use...............................................58
Using the Everyday Case.........................................................................59
General warnings and precautions for the use of your processor ..59
Disposal of electrical components....................................................... 60
O ther information.......................................................................................... 61
Your warranty and registration form....................................................61
Storing your personal details ................................................................. 61
Processor serial number .................................................................... 61
Technical information.............................................................................. 61
Specifications ...................................................................................... 61
Certification and applied standards......................................................65
Equipment classification .........................................................................65
IP rating of processor...............................................................................65
FCC (Federal Communications Commission) and Canadian IC
compliance.................................................................................................65
Labelling symbols.................................................................................... 66
Legal statement ....................................................................................... 68
Glossary............................................................................................................69
Index..................................................................................................................75
195992 Iss3 CP810 user guide 01.indd 5 13/05/2009 4:23:08 PM

195992 Iss3 CP810 user guide 01.indd 6 13/05/2009 4:23:08 PM

Introduction
Purpose of this guide
This user guide is designed to help recipients, parents and carers
understand how to use and take care of the Cochlear™Nucleus®CP810
Sound Processor. The guide provides step-by-step instructions for
wearing and using the processor. It also provides guidance on how to
take care of the processor.
It is important that you read and understand the warnings and
precautions information provided in this guide. The Important
Information Booklet included in the document pack you received with
your processor also contains important safety information about the
processor.
The CP810 and CR110 Troubleshooting Guide provided with your
documentation helps you identify and troubleshoot basic processor
problems.
The Cochlear Nucleus CP810 Sound Processor
The Cochlear Nucleus CP810 Sound Processor is used together with a
cochlear implant to transfer sound to the cochlea, which is the inner ear.
The processor consists of a processing unit, earhook, coil, coil cable and
a battery module. The two buttons on the processing unit allow you to
control the functions of your processor.
You can also use the Cochlear™Nucleus®CR110 Remote Assistant to
control the functions of your processor. It is an easy-to-use remote
control that allows you to communicate with up to two processors at
the same time. It also provides processor troubleshooting assistance.
For information on how to use the remote assistant with your processor,
refer to the Remote Assistant User Guide provided with your processor
documentation.
© Cochlear Limited 2009 CP810 Sound Processor User Guide -7
195992 Iss3 CP810 user guide 01.indd 7 13/05/2009 4:23:08 PM

8 - CP810 Sound Processor User Guide © Cochlear Limited 2009
195992 Iss3 CP810 user guide 01.indd 8 13/05/2009 4:23:08 PM

Getting to know your processor
This section helps you familiarise yourself with your processor.
Processing unit
The processing unit, which is the brain of your processor, converts
sound signals for transfer to your implant.
Figure 2: Processing unit with earhook
Figure 1: CP810 Sound Processor parts
Coil1.
Coil magnet2.
Coil cable3.
Lower button4.
Microphones5.
Upper button6.
Indicator light7.
Earhook8.
Processing unit9.
Battery module10.
Accessory11.
socket cover
1
2
3
4
5
6
7
8
9
10
11
5
© Cochlear Limited 2009 CP810 Sound Processor User Guide - 9
195992 Iss3 CP810 user guide 01.indd 9 13/05/2009 4:23:08 PM

The processing unit allows you to perform the following functions:
Turn your processor on and off.•
Change your program (e.g. from Everyday to Noise).•
Turn the telecoil on and off.•
Lock and unlock processor buttons.•
You can change microphone volume and sensitivity using the remote
assistant. If your processor has an Advanced user interface, you can
also change volume or sensitivity using the processing unit. For more
information, see Advanced userinterface.
The indicator light on the processing unit provides a visual indication
when you perform a function (e.g. when you change a program), or
when there is a problem with the processor (e.g. processor battery is
empty). For more information, see Understanding indicatorlights.
Earhook
The earhook secures the processing unit in place on your ear. It is
attached to the processing unit and is available in a range of sizes. For
more information, see Changing the earhook.
Battery module
You can use a Cochlear™Nucleus®CP800 Series Standard Battery
Module, which uses two disposable batteries (P675 zinc air batteries), or
a Rechargeable Battery Module to power your processor.
Figure 3: Standard Battery Module (1) and Compact Rechargeable Battery Module (2)
12
10 - CP810 Sound Processor User Guide © Cochlear Limited 2009
Getting to know your processor
195992 Iss3 CP810 user guide 01.indd 10 13/05/2009 4:23:10 PM

The Standard Battery Module consists of a battery holder and a battery
cover.
Figure 4: Battery holder with zinc air batteries (1), tamper resistant battery cover (2)
and battery lock (3)
To prevent children from detaching the battery cover from the battery
holder, you can use the Cochlear™Nucleus®CP800 Series Tamper
Resistant Battery Cover. You can also lock the standard battery module
or the rechargeable battery module to the processing unit.
Cochlear supplies a battery charger to recharge the rechargeable battery
module. For more information, see Replacing and recharging batteries.
Coil and coil cable
The coil is a small round disk that you place over the implant. It
transfers electromagnetic signals from your processing unit to the
implant. The coil is attached to a removable coil cable, which plugs into
the processing unit. The coil and coil cable are available in a choice of
colours and lengths. For more information, see Changing the coil cable.
Figure 5: Coil only (1) and coil with cable (2)
2
1
3
1
2
© Cochlear Limited 2009 CP810 Sound Processor User Guide - 11
Getting to know your processor
195992 Iss3 CP810 user guide 01.indd 11 13/05/2009 4:23:13 PM

Coil magnet
A magnet holds the coil in place over your implant.
Figure 6: Coil magnet
If your coil falls off often, or if you experience discomfort, you can
change the depth of the magnet in the coil. You can also use a
stronger or weaker magnet. For more information, see Adjusting and
replacing the coil m agnet.
Microphone protectors
The processor microphones capture sound, which is processed by the
processing unit for transfer to the implant. Microphone protectors
are designed to protect the microphones from dirt and moisture. It
is important that you keep the microphone protectors in place at all
times, and replace them once a month.
Figure 7: Microphone protectors
12 - CP810 Sound Processor User Guide © Cochlear Limited 2009
Getting to know your processor
195992 Iss3 CP810 user guide 01.indd 12 13/05/2009 4:23:19 PM

Processor options
Depending on your listening needs, your clinician can enable the
following options on your processor:
• SmartSound™technologies to improve your hearing. SmartSound
is a suite of four input sound processing technologies. These
technologies are applied to four available programs: Everyday,
Noise, Focus and Music. For more information on these programs,
see Changing programs.
Indicator light flashes that you see when you perform a function,•
or when there is a processor problem. For more information, see
Understanding indicator lights.
Private tones that you hear when you perform a function, or when•
there is a processor problem. A private tone can be heard only by
you. For more information, see Understanding private tones.
Microphone sensitivity or volume that you can change (with•
Advanced user interface only). For more information, see Changing
loudness of sounds.
Telecoil/microphones and accessory/microphones mixing ratios•
that you can change using the remote assistant. For more
information, refer to the Remote Assistant User Guide.
Your processor has been programmed for use with your implant only. It
is important that you only use your own processor and never swap your
processor with another person’s processor. If you have two implants,
correctly match your processor to the correct implant.
Components described in this user guide may not be available in
all countries. Please contact your clinician for more information.
© Cochlear Limited 2009 CP810 Sound Processor User Guide - 13
Getting to know your processor
195992 Iss3 CP810 user guide 01.indd 13 13/05/2009 4:23:22 PM

14 - CP810 Sound Processor User Guide © Cochlear Limited 2009
195992 Iss3 CP810 user guide 01.indd 14 13/05/2009 4:23:22 PM

Wearing your processor
Your processor is designed to fit neatly and comfortably behind your ear.
You can also wear the processing unit behind the ear and attach the
battery module to the body. This provides greater comfort and flexibility
for both adults and children.
You can change the processor coil cable, coil magnet and earhook for
optimal comfort (e.g. if the coil cable length is too short, you can easily
change the cable to a longer one).
This section describes how to wear your processor and wearing options.
Placing your processor on your ear
To be able to hear sound from the processor, it needs to be placed on
the ear.
To place your processor on your ear:
Place the processing unit over your ear while holding the coil in the1.
other hand.
Place the coil on your head. The coil magnet should hold it in place2.
over your implant.
You may find it easier to turn on your processor before placing it on
your ear. To turn it on, press and hold the lower button for at least one
second until you see short flashes of green. The number of flashes you
see corresponds to the number of your current program (e.g. if your
current program is program 2, you see two green flashes).
When you turn on your processor before placing it on your ear, you may
see flashes of orange. This indicates that the coil is not placed on your
head. If the flashes do not stop even after placing the coil on your head,
see Understanding indicator lights for more information.
© Cochlear Limited 2009 CP810 Sound Processor User Guide - 15
195992 Iss3 CP810 user guide 01.indd 15 13/05/2009 4:23:22 PM

Attaching the coil and coil cable
If the coil is not attached to the processing unit, or the coil cable is
not attached to the coil, you need to attach them before placing the
processor on your ear.
Attaching the coil cable to the coil
To attach the coil cable to the coil:
H old the coil in one hand1.
and the coil cable plug in the
other hand as shown.
Align the coil end of the coil2.
cable plug with the coil.
Push the coil cable plug3.
firmly into the coil until it
clicks into place.
Attaching the coil to the processing unit
To attach the coil to the processing unit:
Align the coil cable plug with1.
the coil cable socket on the
processing unit.
Push the coil cable plug2.
firmly into the socket until it
clicks into place.
16 - CP810 Sound Processor User Guide © Cochlear Limited 2009
Wearing your processor
195992 Iss3 CP810 user guide 01.indd 16 13/05/2009 4:23:22 PM

The coil functions properly only when the coil cable is fully inserted
into the processing unit. To check if the coil is receiving sound signals
from the processor, you can use the in-built coil sensor on the remote
assistant. For more information on how to use the coil sensor, see
Checking the coil.
If you attach the coil to the processing unit when your processor
is turned on, your processor may turn off. If this occurs, turn your
processor back on.
A secure and comfortable fit
For a more secure or comfortable fit, you may want to:
Change the earhook size.•
Adjust the coil magnet strength.•
Change the coil magnet.•
Change the coil cable.•
Use the Snugfit• ™.
Use the LiteWear cable, which allows the battery module to be•
attached to the body.
Read the following sections for more details.
© Cochlear Limited 2009 CP810 Sound Processor User Guide - 17
Wearing your processor
195992 Iss3 CP810 user guide 01.indd 17 13/05/2009 4:23:34 PM

Changing the earhook
Earhooks are available in different sizes. If your earhook becomes loose,
you should replace it.
To change the earhook:
Hold your processor and1.
the earhook as shown.
Rotate the earhook to pull2.
it away from the processing
unit.
•
Hold the new earhook3.
in one hand and your
processor in the other hand
as shown.
Attach the earhook by4.
pushing the lower end of the
earhook onto the processing
unit.
Avoid twisting the earhook as it may become loose.
Adjusting and replacing the coil magnet
If the magnet strength is too weak, the coil may fall off. If it is too
strong, it may cause discomfort or skin irritation. You may consult your
clinician if you are unsure about correct magnet strength.
Make sure the coil is positioned correctly against the implant by placing
it where the coil magnet “pull” feels the strongest. You can change how
firmly the magnet sits on your head by adjusting its depth in the coil.
18 - CP810 Sound Processor User Guide © Cochlear Limited 2009
Wearing your processor
195992 Iss3 CP810 user guide 01.indd 18 13/05/2009 4:23:34 PM

If adjusting the depth of the magnet is not sufficient, you can replace
the magnet with a stronger or weaker magnet.
Adjusting magnet depth
To adjust magnet depth:
Place the thumb and index1.
finger on the magnet as
shown.
Turn the magnet in a2.
clockwise direction to
increase magnet strength,
or in an anti-clockwise
direction to reduce
strength.
Changing magnet strength
To change the magnet to a stronger or weaker one:
Place the thumb on the top1.
of the magnet and index
finger on the underside of
the magnet as shown.
Turn the magnet in an anti-2.
clockwise direction until
you remove it from the
topside of the coil.
© Cochlear Limited 2009 CP810 Sound Processor User Guide - 19
Wearing your processor
195992 Iss3 CP810 user guide 01.indd 19 13/05/2009 4:23:40 PM

Hold the new magnet3.
between the thumb and
index finger as shown.
Hold the coil in the other4.
hand.
Insert the magnet gently5.
into the magnet slot on the
topside of the coil. The side
with the star should face
upwards. The magnet fits
easily.
Turn the magnet in a clockwise direction until it is in position.6.
Do not overtighten the magnet, or force it to turn if it becomes difficult
to turn during insertion or removal. The movement should be smooth
and turning should need only a small amount of force. If turning
becomes difficult, check that:
The magnet is correctly aligned in the coil.•
You are turning the magnet in the correct direction.•
Changing the coil cable
If you find that the coil cable is too long or short for your comfort, you
can change the coil cable. Regularly check to see if the coil cable is
damaged. If damaged, you will need a new coil cable.
20 - CP810 Sound Processor User Guide © Cochlear Limited 2009
Wearing your processor
195992 Iss3 CP810 user guide 01.indd 20 13/05/2009 4:23:46 PM