Cole Parmer HO-200 Series User manual

Cole-Parmer
HO-200 Series Homogenizer
User Manual

This manual is a guide for the use of the Cole-Parmer HO-200 Series Homogenizer and accessories.
Data herein has been veried and validated. It is believed adequate for the intended use of the
instrument. If the instrument or procedures are used for purposes over and above the capabilities
specied herein, conrmation of the validity and suitability should be obtained, otherwise Cole-
Parmer does not guarantee results and assumes no obligation or liability. This publication is not a
license to operate under, or a recommendation to infringe upon, any process patents.
Notes, cautions, and warnings within the text of this manual are used to emphasize important and
critical instructions.
This Cole-Parmer product is warranted to be free from defects in material and workmanship for a
period of TWO YEARS from the date of delivery. Cole-Parmer will repair or replace and return free of
charge any part which is returned to its factory within said period, transportation prepaid by user,
and which is found upon inspection to have been defective in materials or workmanship. For the
rst 90 days, both parts and service are without charge. For the balance of the period, parts will
be provided but service will be charged at established labor rates. This warranty does not include
normal wear from use; it does not apply to any instrument or parts which have been altered by
anyone other than an employee of Cole-Parmer nor to any instrument which has been damaged
through accident, negligence, failure to follow operating instructions, the use of electric currents
or circuits other than those specied on the plate axed to the instrument, misuse, or abuse. Cole-
Parmer reserves the right to change, alter, modify, or improve any of its instruments without any
obligation whatever to make corresponding changes to any instrument previously sold or shipped.
THE FORGOING OBLIGATION IS IN LIEU OF ALL OBLIGATIONS AND LIABILITIES INCLUDING
NEGLIGENCE AND ALLWARRANTIES OF MERCHANTABILITY OR OTHERWISE, EXPRESSED OR IMPLIED
IN FACT OR BY LAW, AND STATE OUR ENTIRE AND EXCLUSIVE LIABILITY AND BUYERS EXCLUSIVE
REMEDY FOR ANY CLAIM OF DAMAGES IN CONNECTIONWITHTHE SALE OR FURNISHING OF GOODS
OR PARTS, THEIR DESIGN, SUITABILITY FOR USE, INSTALLATION, OR OPERATION. Cole-Parmer WILL
IN NO EVENT BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, AND
THEIR LIABILITY UNDER NO CIRCUMSTANCES WILL EXCEED THE CON-TRACT PRICE FOR THE GOODS
FOR WHICH LIABILITY IS CLAIMED.

The Cole-Parmer HO-200 consists of the following:
Description Quantity
Motor Drive Unit (115V) 1
Or Motor Drive Unit (220V)
Clamp 1
Tool Kit 1
Soft Tissue Tip 1
Hard Tissue Tip 1
Adapter 1
Instruction Manual 1
Overview
1
2
3
4
5
6
1. Power Cord
2. On/O Switch
3. Speed Control
4. Motor Brushes
5. Thumb Screw
6. Probe Coupling
ClampAdapter
Optional Stand Available (sold separately)

1. Slide the HO-200 into the opening
on the end of the post clamp
assembly and push it down rmly.
The unit will lock in place.
2. To release the motor, press the clamp
release button on the back of the
opening of the post clamp assembly
and lift the motor from the cradle.
3. Slide the post clamp assembly
down over the end of the post until
the clamp is at the desired height
and lock in place.
Stand Mounting
Push to lock
into Clamp
Stand
(sold separately)
Clamp
Clamp
Release Button

*Never run dry
Accessories
Generator Probes
1. Insert Generator
Probe into coupling
2. Quarter turn
clockwise to lock
3. Tighten
Thumbscrew
4. Ready to use
*always submerge probe
in liquid before starting
1/4 Turn
4. Quarter turn
clockwise to lock
5. Ready to use
*always submerge probe
in liquid before starting
3. Insert Tip
into adapter
1. Insert Adapter
into coupling
2. Quarter turn
clockwise.
Tighten
Thumbscrew
Cole-Parmer Tips and Adapter
1/4 Turn
1/4 Turn
*Never run dry

Operation
General Operation
Power
- Plug in the power cord
Start
- Move the On/O switch on the front of the unit to
the On position.
Set Speed
- Adjust speed using the speed control.
To increase rpm, move control from left to right.
Stop
- Move the On/O switch to the O position.
1. Power Cord
2. On/O switch
3. Speed Control
1
2
3
Size Processing Range Type Part No.
5 mm x 75 .02 mL - 5 mL Flat Bottom 04727-60
Flat Bottom-Wide Window 04727-62
7 mm x 115 mm .25 mL - 30 mL Saw Tooth 04727-33
Saw Tooth- Wide Window 04727-35
10 mm x 115 mm 1.5 mL - 100 mL Saw Tooth 04727-37
Saw Tooth- Wide Window 04727-39
Type Size Quantity Part No.
Hard Tissue 7 mm x 110 mm 25 Pack 04727-84
7 mm x 110 mm 50 Pack 04727-85
Soft Tissue 7 mm x 110 mm 25 Pack 04727-86
7 mm x 110 mm 50 Pack 04727-87
Sterile 7 mm x 110 mm 25 Pack 7890480
Generator Probes
Plastic Disposable Generator Probes

Troubleshooting
PROBLEM CORRECTIVE ACTION
The Cole-Parmer HO-200 is plugged in
and turned on but is not functioning.
- Check power cord connectors
- Check wall socket for power to the
outlet
Motor is turned ON and makes a makes a
“buzzing”sound, but is not working.
- Check that the brushes are not worn
and are correctly installed.
Motor unit operating speed declines,
stalls intermittently, or stops completely
- Check that the brushes are not worn
and are correctly installed.
PTFE bearing wears quickly - Fluid level may be too low in the tube.
- Immerse the probe deeper
into the uid.

625 East Bunker Ct
Vernon Hills, IL U.S.A.
1 [phone]
www.COLEPARMER.com
Beacon Road
Stone, Staffordshire, ST15 0SA, UK
[phone]
PN 03-2016 Rev A