Collomix TMX 1000 User manual

Collomix GmbH TMX 1000 - 110 v US
85080 Gaimersheim TMX 1500 - 240 v US
Rev. 5 Page 1
Operang instrucons
Pan Mixer
TMX 1000 Ref. 37082 (110V/60 Hz US)
TMX 1500 Ref. 37083 (240V/60 Hz US)
This manual must accompany the equipment at all mes!

TMX 1000 - 110 v US Collomix GmbH
TMX 1500 - 240 v US 85080 Gaimersheim
Page 2 Rev. 5
1 Mains plug 8 Mixing tool
2 ON/OFF switch 9 Lid with safety grid
3 Lashing eyes 10 Discharge Handle
4 Transport rollers 11 Vibrang device
5 Unlocking mechanism for lid 12 Discharge chute
6Connecon for vacuum cleaner 13 Foot
7 Bag opener 14 Thermal overload protecon (only TMX 1500)
Components
1
2
4
5
67
8
9
10
11
12
14
13
3

Collomix GmbH TMX 1000 - 110 v US
85080 Gaimersheim TMX 1500 - 240 v US
Rev. 5 Page 3
Signs and symbols
Warnings
The following symbols and signal words are used in this documentaon.
Symbol Meaning
DANGER
If this signal word is used, death or serious injuries will occur if the respecve
precauonary measures are not observed.
WARNING
If this signal word is used, death or serious injuries may occur if the respec-
ve precauonary measures are not observed.
CAUTION
If this signal word is used, minor injuries may occur if the respecve precau-
onary measures are not observed.
ATTENTION If this signal word is used, malfuncons or material damage may occur if the
respecve precauonary measures are not observed.
IMPORTANT If this signal word is used, operang ps or cross-references will follow.
Structure of warnings
DANGER
The rst line describes the type and source of the danger
The second line describes the consequences if no danger prevenon measures are taken.
 The last line describes danger prevenon measures.
WARNING
Risk of injuries due to non-observance of the safety symbols
Non-observance of the warnings on the device and in the operang instrucons can lead to injuries
and further dangers.
 Observe the warnings on the device and in the operang instrucons.
Symbol Explanaon Symbol Explanaon
Observe informaon Pull the mains plug aer every use.
Pull the mains plug prior to opening
the housing.
Symbol Explanaon Symbol Explanaon
Warning against a danger
point
Warning against dangerous elec-
trical voltage
The following special safety symbols are used in respecve passages in these operang instrucons:
Mandatory signs

TMX 1000 - 110 v US Collomix GmbH
TMX 1500 - 240 v US 85080 Gaimersheim
Page 4 Rev. 5
Technical data
Model TMX 1000 TMX 1500
Capacity, mixing bucket, nominal 26 gal. 40 gal.
Maximum mixing volume 20 gal. / 2.8 cub. . 32 gal. / 3,6 cub. .
Output 2.7 hp /110 V~ 60 Hz / 8.1 A 3.6 hp/240 V~ 60 Hz
Speed, mixing tool 30 rpm (no load) 30 rpm (no load)
Weight (empty) 289 lbs 304 lbs
Protecon class IP 44 IP 44
Dimensions 33.1 x 29.7 x 46.1” 33.1 x 29.7 x 49.6”
Arcle number TMX 37082 (110V - US) 37083 (240V - US)
Noise emission according to 2006/42/EC
Sound power LWA / Guaranteed sound level 86 dB (A) 86 db (a)
Measuring inaccuracy KpA + WA 1.2 dB 1.2 dB
Declaraon of EC Conformity
We hereby declare on our sole authority that this product complies with the following stand-
ards or normave documents:
EN 12151:2007; EN 20204-1:2006/+A1: 2009; EN 61000-3-2:2014; EN 61000-3-3:2013; EN
55014-1:2006/+A1: 2009/+A2:2011; EN 55012-2:2015; EN ISO 3744:2010
as per the provisions of Direcves 2014/30/EU, 2006/42 EC, 2011/65/EU; 2000/14/EC
Gaimersheim, 16/02/2017
A. Essing, Execuve Management
Technical documentation to be requested from”
Collomix GmbH
Technical Development Department
Daimlerstr. 9, 85080 Gaimersheim
Germany
Scope of delivery
1 Machine with mixing tool
1 Operang instrucons
About this document
These instrucons use symbols and labels that help you in nding informaon quickly. Read
the respecve explanaons in the following secon. Read the safety and warning informaon
in these instrucons parcularly thoroughly. You can nd the safety informaon starng from
page 6. Refer to the chapter introducons and passages leading up to instrucons for warnings.
The copyright for images and texts remains with Collomix GmbH.
You must read the operang instrucons prior to inial commissioning. Observe the safety in-
formaon. Keep for future use. This documentaon is not monitored by a change service.

Collomix GmbH TMX 1000 - 110 v US
85080 Gaimersheim TMX 1500 - 240 v US
Rev. 5 Page 5
For your safety
WARNING
The TMX mixer was developed, produced and tested complying with the fundamental safety
requirements. Despite that, there are residual risks.
• For this reason, read the operang instrucons prior to operang the machine.
• Store the operang instrucons readily available at the machine.
• Pass on the operang instrucons to any subsequent owners.
• Despite all precauons taken, non-obvious residual risks may exist. Residual risks can be
reduced by observing the safety informaon, the intended use and the operang instruc-
ons overall.
Consideraon and cauon reduce the risk of personal injuries and damage.
• Electrical hazard if improper connecon lines are used.
• Contact with live parts if electrical components are open.
CALIFORNIA - PROPOSITION 65 WARNING
Grinding/cung/drilling and other construcon acvies contains chemicals know th the
State of California to caus cancer, birth defects and other reproducve harm. Some exam-
ples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silicia from bricks.
• Cement and other masonry products.
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how ogten you do this type of work. To
reduce your exposure to these chemicals: ALWAYS work in a well venlated area, and work
with approved safety equipment, such as dust masks that are specially designed to lter out
microscopic parcles, or use an appropriate dust extracon system with micro part lter
linked to the machine, to lter out microscopic parcles.

TMX 1000 - 110 v US Collomix GmbH
TMX 1500 - 240 v US 85080 Gaimersheim
Page 6 Rev. 5
Safety informaon
Read and observe this information prior to using the device! Non-observance can result in
direct consequences for your health and physical integrity , as well as for the health and
physical integrity of third parties.
XThe machine may only be used and maintained by persons familiar with the operating
instructions and the applicable regulations regarding occupational safety and accident
prevention.
XThe machine may only be used in proper technical conditions as well as for the intended
purpose and in a safety- and danger-concious manner. In particular, damage that can
impact the safety must be corrected immediately. Do not put the machine into operation!
XRepairs may only be carried out by recognised expert personnel or the manufacturer.
XDo not operate the device in rooms with flammable atmosphere. Risk of explosion!
XDo not mix any solvent-containing substances with a flash point below 70°F / 21 °C.
XDo not reach with your hand or objects into the mixing device during ongoing mixing
operation. Risk of crushing!
XWear tight-fitting clothes, safety shoes and no jewellery during work. Wear a hairnet for
long hair.
XThe use of a dust extraction and wearing a dust mask are recommended as protection
against health-hazardous dusts in the area of the machine.
XWear safety gloves and safety shoes wile working with the machine.
XEnsure a firm and level location. Make sure that the device cannot tilt.
XObserve the electrical regulation at the usage location when setting up the device.
XMake sure that the voltage indicated on the rating plate matches the mains voltage.
XRealisation of the connection lines according to IEC 60245 (H 07 RN-F) with a wire
cross-section of at least AWG 16 for a cable length of up to maximum 25 m, or AWG 13
for a cable length greater than 25 m
XOnly use connection lines with a splash-proof rubber plug connection for difficult condi-
tions.
XDo not connect the device to standard electrical sockets. Always connect the devices via a
residual current device (RCD) with a response current of 30 mA or less.
XIf a cable reel is used, the cable must be fully unwound. There is a risk of a cable fire due
to heating. A loss of power may occur as well, leading to the undervoltage protection being
triggered.
XRepairs on electrical components may only be carried out by a recognised electrician,
complying with the local regulations.
XElectrical operating equipment must be subjected to a regular inspection by an electrician
(according to German Social Accident Insurance.
XKeep the device away from rain and moisture. Water penetration into an electrically oper-
ated machine increases the risk of an electric shock.
XAlways pull the mains plug during non-operation, maintenance or when replacing the
mixing tool.
XDo not disconnect the plug from the socket by pulling on the cord. Protect the cable
against heat, oil, bending and sharp edges.
XCheck the cable for damage or defects prior to use.
XWait, until the device and/or tool comes to a complete standstill. Rotating tools can get
stuck and cause injuries or damage.
XOnly remove material samples with the device at standstill.
XAcute risk of accidents and injuries if the safety functions are disabled on purpose. In this
RCD 30mA

Collomix GmbH TMX 1000 - 110 v US
85080 Gaimersheim TMX 1500 - 240 v US
Rev. 5 Page 7
case, the warranty shall become void.
XCheck the machine regularly for flawless function and damage. Do not put the machine in
operation with damaged or defective safety components.
XDo not clean the machine using a high-pressure cleaner or hose – risk of electric shock!
XDo not expose the machine to any rain, not even during transportation.
XObserve the processing and safety information of the manufacturer for the material to be
mixed.
XThe machine must be firmly lashed in at least three directions for vehicle transport.
XOnly operate the machine with the TMX 1000 mixing tool that is suitable for the machine.
XOnly use original spare parts. The use of third-party spare parts may lead to accidents of
the user. The manufacturer shall not be liable for any resulting damage.

TMX 1000 - 110 v US Collomix GmbH
TMX 1500 - 240 v US 85080 Gaimersheim
Page 8 Rev. 5
Intended use
Foreseeable misuse
The TMX model is a mixing device that is suitable for mixing so to viscoplasc material as
well as hard and granular material. Examples include:
• All types of mortar
• So to plasc screeds and concretes with addives up to max. 5/8” / 16 mm
• Lime-cement plaster
• Dierent cement-based adhesives
• Terrazzo (TMX 1000, with addional with addional rubber lips to be upgraded)
• Heavy epoxy resin mortar
as they are used in the construcon industry.
The recommended mixing capacity amounts to a maximum of 21 gal. per mixture (material-de-
pendent). It is recommended to test the necessary material mixing me at the beginning of
your work.
Observe the processing informaon of the material manufacturer regarding the used material.
Any other use of the machine or any use beyond this scope is considered unintended and thus
improper. Safety and its protecon can be impacted in this case. Collomix GmbH shall not be
liable for any resulng damage. Intended use also includes:
• Compliance with all informaon in the operang instrucons
• Compliance with all safety informaon
• Compliance with inspecon and maintenance work.
The user shall be liable for damage resulng from non-intended use.
Reasonably foreseeable misuse that could result in danger for the user, third pares or the
machine includes:
• Use of the machine and its accessories contrary to the intended use.
• Operaon of the machine using a mixing tool dierent from the specied one.
• Use of damaged containers or containers not suitable for the mixer.
• Mixing of liquid and runny materials.
• Mixing of ammable or explosive substances.
• Mixing of electrically conducng substances.
• Mixing of chemically aggressive substances and corrosive liquids.
• Mixing of food items.
• Operaon of the machine outside of the physical usage limits described in chapter “Com-
missioning/operaon”.
• Bucket overlling
• Use of water jets or high-pressure cleaners for cleaning
• Changes to the mixer as well as add-ons or retrots without previous agreement with Col-
lomix GmbH.
• Operaon of the machine contrary to the provisions of the operang instrucons with re-
spect to safety informaon, installaon, operaon, maintenance, setup and malfuncons.
• Bypassing, removal or disabling of safety and protecon devices of the machine.
• Operaon of the machine in the case/with obvious malfuncons
• Repair, cleaning and maintenance work without disconnecng the mixer from the power
supply

Collomix GmbH TMX 1000 - 110 v US
85080 Gaimersheim TMX 1500 - 240 v US
Rev. 5 Page 9
Funconality
The machine consists of a mobile frame with a permanently mounted mixing bucket made of
steel sheet. A 3-arm mixing tool rotates in the mixing drum around a central drive axis.
The mixing vessel is lled with the respecve amount of water. Next, the respecve amount of
powdery material, possibly with addive (sand, gravel) is added with the mixer running.
The materials are usually mixed and ready for use within three to ve minutes. Observe the
informaon of the material manufacturer and check the mixing quality using a test mixture.
Open the segment slidegate at the boom of the bucket to empty the mixer during operaon.
The rotang mixing tool conveys the material to the discharge chute.
Transport informaon
The machine is delivered on a pallet without wheels. Observe the assembly instrucons.
The empty weight of the machine amounts to 289 lbs (TMX 1000) /304 lbs (TMX 1500).
ATTENTION!
The machine must always be suciently secured against lng and rolling away using several
transport straps for vehicle transport. Non-secured loads can result in serious personal injury
and material damage.
Lash the machine via the lashing eyes with lashing strips of a sucient size.
The lashing eyes are not suitable for transportaon by crane.
Assembly
The following tools are required for inial assembly:
1 x open-end wrench SW 10; 2 x open-end wrench SW 17
Removal of the transport lock:
Loosen the screw connecons of the four feet on the pallet. (Open-end wrench SW 10 )
Adjusng the height:
ATTENTION!
Risk of pping! Seek the assistance of a second person in this regard.
Loosen the 4 screws on the two front feet using two open-end wrenches SW 17. Tilt the ma-
chine unl it becomes possible to insert the 4 screws into the upper bores. Then ghten the
screws again.

TMX 1000 - 110 v US Collomix GmbH
TMX 1500 - 240 v US 85080 Gaimersheim
Page 10 Rev. 5
Prior to commissioning
The machine must always be checked for damage prior to each commissioning.
Make sure that the machine is standing securely on a rm and level surface. Risk of pping!
Electrical installaon
Check that the voltage indicated on the type plate matches the available mains voltage.
Connect the mains plug of the machine to the power supply socket using a suitable extension
cord (type H07 RN-F, at least AWG 16). This socket must feature a residual current device (RCD).
Do not connect to standard electrical sockets.
Opening the lid
Pull the release knob with one hand and li the lid at the same me with the second hand. The
lid is locked when in open state. The release knob needs to be pulled again to close the lid.
Connecng the vacuum cleaner
In order to signicantly reduce the dust load when lling the material and at the start of the
mixing process, we recommend connecng a deduster to the hose supports (Ø 35 mm) of the
lid. The deduster used must comply with dust class “M”.
Mixing tool
Check whether the mixing tool is correctly mounted and fully seated on the sha.
If necessary, you can adjust the individual mixing paddles.

RCD 30mA
Mounng the wheels:
Before you put the wheel on the relevant axle, one of the accompanying washers needs to be
inserted. Once this has been done, aach the wheel and one further washer to conclude. Se-
cure the wheels with the accompanying coers as well.
A

Collomix GmbH TMX 1000 - 110 v US
85080 Gaimersheim TMX 1500 - 240 v US
Rev. 5 Page 11
Operaon
XClose the protecve grang and make sure that it is locked.
XSwitch on the mixer. Press the green start buon.
XFill the necessary amount of water into the mixing bucket.
XIf installed, switch on the vacuum cleaner.
XPlace the material sack with its broad side on the grid cover with the bag ripper and move
it back and forth slightly unl the sack is fully open. Gradually ll the content of the bag
into the bucket.
XPay aenon during the mixing process to determine whether the material is mixed to a
sucient extent.
XTo empty the mixing bucket, open the boom segment slide using the lever.
XEmpty the mixed material into a bucket or wheelbarrow.
XPress the red OFF buon “0” to switch o the machine. The machine comes to a stop.
The machine is ed with a protecon switch. It switches the machine o in the event of over-
loading/overheang. Let the motor cool down and restart the machine.
The machine is fitted with an undervoltage trigger. If it triggers, the machine is stopped. This
may occur due to the following reasons:
• Voltage drop in the mains supply
• Supply cable too long
• Power supply disconnected
Restart after the malfunction is corrected.
IMPORTANT:
Observe the informaon in the technical data sheets of the material manufacturers.
The necessary mixing me depends on the quanty and viscosity of the material.
WARNING
Risk of injuries due to rotang mixing tool.
Do not reach into the mixing drum or handle tools in the mixing drum during mixing.
ATTENTION
Only use the mixer for the tasks listed in chapter “Intended use”. Observe the safety infor-
maon respecvely.
Removing the mixing tool
Unlock and open the cover with the protecve grang.
The mixing tool rests on the hexagonal pin of the drive sha without addional aachment.
You can easily li the mixing tool o of the sha. It may happen that you need to move the tool
back and forth a lile if it has strued apart.
The individual mixing paddles can be replaced. To do this, loosen the screw connecons on the
arms of the mixing tool.

TMX 1000 - 110 v US Collomix GmbH
TMX 1500 - 240 v US 85080 Gaimersheim
Page 12 Rev. 5
Care and maintenance
Troubleshoong
The mixer must always be disconnected from the power supply by pulling the mains plug prior
to any maintenance and cleaning work.
Always ensure ease of movement for all moving parts.
The mixer is largely maintenance-free. The drive sha is supported by ball bearings with per-
manent lubricaon.
Clean the machine immediately aer use. Do not let material deposits dry.
Remove the mixing tool from the hexagon sha and clean it outside of the mixer.
Do not tap the mixing tool and mixing tub using a hammer. Bent mixing tools can lead to dam-
age to the device and poor mixing results.
Replace damaged, bent or worn machine parts.
Treat moving parts, such as the boom segment slidegate, extendable discharge chute and
hexagons sha from me to me with spray oil.
Malfuncon Cause Remedy
Machine does not start
• Supply cable too long and/or cable
cross-section too small
• Plug not inserted
• No mains voltage present
• Capacitor defective
• Check cable cross-section, must be AWG 16,
shorten supply cable
• Insert plug
• Check mains voltage
• Replace starting capacitor*
Machine switches off after
a short time , cannot be
switched on again
• Thermal overload protection trig-
gered (overload of the machine) -
- only for TMX 1500
• Supply cable too long and/or cable
cross-section too small
• Cable was pulled from the mains
plug
• Voltage drop in the power supply
• Capacitor defective
• Let machine cool down (at least 2 min), reduce
mix as needed
• Check cable cross-section, must be AWG 16,
shorten supply cable
• Insert cable again
• Check mains voltage
• Replace starting capacitor*
Machine does not start up
when filled, remains at a
standstill
• Mixing quantity too high
• Mixed material too tough
• Reduce the material volume
* Work on live components may only be carried out by a qualied electrician!

TMX 1000 - 110 v US Collomix GmbH
TMX 1500 - 240 v US 85080 Gaimersheim
Page 13 Rev. 5
Repair
Have repairs on the electrical system only performed by expert personnel or Collomix Factory
Service.
Only use original Collomix accessories and spare parts.
Service instructions and the current list of spare parts can be found on our homepage:
www.collomix.com
DANGER
Danger to life due to dangerous electrical voltage
Never open the covers or safety devices of the machine. Repairs may only be performed by
trained expert personnel. After repair completion, verify and document the proper condition
of all safety devices and the electrical equipment.
Do not reconstruct, change or remove safety-relevant parts!
Additional add-ons may not impact safety and must be approved by the manufacturer.

Collomix GmbH TMX 1000 - 110 v US
85080 Gaimersheim TMX 1500 - 240 v US
Rev. 5 Page 14
Disposal
Recycle the device, accessories and packaging in an environmental friendly manner. Do not
dispose of in household waste.
Non-functional electrical equipment can be recycled at public collection centres for electrical
waste.
Warranty
The manufacturer offers a product warranty within the scope of the delivery terms and in
accordance with legal / country-specific regulations. Please include your payment receipt or
delivery note with any warranty claims.
Please return the device to us if you detect any irregularities. Complaints / claims can only be
considered if the device is delivered to the Collomix Service department in a complete and
undismantled state.
Any damage resulting from normal wear, overload, improper handling, non-approved accesso-
ries or insufficient maintenance shall be exempt from the warranty.
Any repairs carried out by third parties shall release us from any warranty obligation.
Any structural or functional changes to the device not authorised by us shall result in the inval-
idation of the warranty as well as the declaration of conformity.
Please enclose a proof of purchase with a warranty claim.
Any warranty and liability claims are excluded in the case of personal injuries and/or material
damage, if they are caused by one or several of the following causes:
• Unintended use of the machine
• Improper commissioning, operaon and maintenance of the machine
• Damage due to excessive contaminaon and/or insucient cleaning.
• Unauthorised structural changes of the machine
• Improperly performed repairs and/or use of third-party spare parts.
Consumables
The following consumables are available:
Part Art. no.
Mixing tool TMX 1000 37250
Mixing tool TMX 1500 37251

Collomix GmbH TMX 1000 - 110 v US
85080 Gaimersheim TMX 1500 - 240 v US
Rev. 5 Page 15

TMX 1000 - 110 v US Collomix GmbH
TMX 1500 - 240 v US 85080 Gaimersheim
Page 16 Rev. 5
Manufacturer:
Collomix GmbH
Daimlerstraße 9
85080 Gaimersheim
Germany
inf[email protected]
Subject to change
© Collomix GmbH
2020-08
Art.no. 07034-040
Distributor for
UNITED STATES - CANADA - MEXICO
Collomix North America Inc.
648 Crescent Court
Milwaukee, WI 53213
Tel. + 1 - 414 471 38 83
Fax + 1 - 414 918 80 32
Email al.karrak[email protected]
Web www.collomix.us