ComAp InteliLite4 AMF20 Manual

Copyright © 2021 ComAp a.s.
Written by Jan Liptak
Prague, Czech Republic
ComAp a.s., U Uranie 1612/14a,
170 00 Prague 7, Czech Republic
Tel: [phone]
E-mail: [e-mail], www.comap- Operator Guide
control.com

InteliLite 4 AMF20+AMF25 Operator Guide 2
1 Front panel elements
Image 1.1 Operator interface of InteliLite 4 AMF20/AMF25
Control buttons
Position
Picture
Description
LEFT button. Use this button to move left orto change the mode. The
button can change the mode only if the main screen with the indicatorof
currently selected mode is displayed.
Note: This button will not change the mode if the controller mode is
forced by one of binary inputs listed in the Reference Guide –"Operating
modes" chapter.
RIGHT button. Use this button to move right orto change the mode.
The button can change the mode only if the main screen with the
indicatorof currently selected mode is displayed.
Note: This button will not change the mode if the controller mode is
forced by one of binary inputs listed in the Reference Guide –"Operating
modes" chapter.
HORN RESET button. Use this button to deactivate the horn output without
acknowledging the alarms.

InteliLite 4 AMF20+AMF25 Operator Guide 3
FAULT RESET button. Use this button to acknowledge alarms and
deactivate the horn output. Inactive alarms will disappearimmediately
and status of active alarms will be changed to "confirmed" so they will
disappear as soon as theirreasons dismiss.
UP button. Use this button to move up orincrease value.
PAGE button. Use this button to switch overdisplay pages.
DOWN button. Use this button to move down ordecrease value.
ENTER button. Use this button to finish editing a setpoint ormoving right in
the history page.
START button. Works in MAN mode only. Press this button to initiate the
start sequence of the engine.
STOP button. Works in MAN mode only. Press this button to initiate the
stop sequence of the Gen-set. Repeated pressing of button will cancel
current phase of stop sequence (like cooling)and next phase will
continue.
GCB button. Works in MAN mode only. Press this button to open orclose
the GCB.
MCB button. Works in MAN mode only. Press this button to open orclose
the MCB.
Indicators and others
Position
Description
GENERATOR status indicator. There are two states –Gen-set OK (indicatoris
green)and Gen-set failure (indicatoris red). Green LED is on if the generatorvoltage and
frequency is present and within limits. Red LED starts flashing when Gen-set failure
occurs. After FAULT RESET button is pressed, Red LED goes to steady light (if an
alarm is still active) oris off (if no alarm is active).
MAINS status indicator. There are two states –Mains OK (indicatoris green)and
Mains failure (indicatoris red). Green LED is on, if mains is present and within limits.
Red LED starts blinking when the mains failure is detected and afterthe Gen-set has
started and connected to the load it lights permanently until the mains failure
disappears.
Graphic B/W display, 132 × 64 px.

InteliLite 4 AMF20+AMF25 Operator Guide 4
GCB Status. Consists of 3 green LEDs. The middle green LED is on if GCB is closed. It is
driven by GCB CLOSE/OPEN output orby GCB feedback signal. Side green LEDs are on
in case the generatorstatus indicatoris ok.
LOAD. Green LED is ON if load is supplied by mains orby generator. It means, that
Genset ormains is OK and propercircuit breakeris closed.
MCB Status.Consists of 3 green LEDs. The middle green LED is on if MCB is closed. It is
driven by MCB CLOSE/OPEN output orby MCB feedback signal. Side green LEDs are on
in case the mains status indicatoris ok.
6 back to Front panel elements

InteliLite 4 AMF20+AMF25 Operator Guide 5
2 Display screens and pages
structure
The displayed information is structured into "pages" and "screens". Use PAGE button to switch overthe pages.
The page Measurement consists of screens which display measured values like voltages,
current, oil pressure etc., computed values like i.e. gen-set power, statistic data and the alarm list on the
last screen.
The page Setpoints contains all setpoints organized to groups and also a special group
forentering password.
The page History log shows the history log in the orderthat the last record is displayed first.
2.1 Main Screen
2.1.1 Symbols
Padlock –active when LBI ACCESS LOCK is active
R –active when there is active remote connection to controller
Exclamation mark –active when there is any alarm in alarmlist
2.1.2 Optional
Value can be chosen via setpoints Main Screen Line 1 (page 1)and Main Screen Line 2 (page 1).
Posibilities are: RPM, PF, Run Hours, ATT, AIN1
2.2 Measurement Screens

InteliLite 4 AMF20+AMF25 Operator Guide 6
Note: Use Up and Down button to
move between measurement
pages.
Note: Use Up and Down button to
move between measurement
pages.
Note: Use Up and Down button to
move between measurement
pages.
Note: Use Up and Down button to move between measurement pages.

InteliLite 4 AMF20+AMF25 Operator Guide 7
Note: Use Up and Down button to move between measurement
pages.
Note: Use Up and Down button to move between measurement pages.
Note: Use Up and Down button to move between measurement pages.

InteliLite 4 AMF20+AMF25 Operator Guide 8
Note: Use Up and Down button to move between measurement pages.
Note: Use Up and Down button to move between measurement pages.
Note: Use Up and Down button to move between measurement pages.

InteliLite 4 AMF20+AMF25 Operator Guide 9
Note: Use Up and Down button to move between measurement pages.
Note: Available only with plug-in module.
Note: Use Up and Down button to move between measurement pages.
Note: Available only with plug-in module.
Note: Use Up and Down button to move between measurement
pages.
Note: Use Up and Down button to move between measurement pages.

InteliLite 4 AMF20+AMF25 Operator Guide 10
Note: Use Up and Down button to move between
measurement pages.
Note: Use Up and Down button to move between
measurement pages.
Note: Use Up and Down button to move between
measurement pages.
Note: Use Up and Down button to move between
measurement pages.
Note: Available only with plug-in module.