Comelit 1414 User manual

EN
TECHNICAL
MANUAL
SBTOP riser branch module
Art.1414 Passion.Technology.Design.

Warning
Intended use
This Comelit product was designed for use in the creation of audio and video communication systems in residential,
commercial or industrial settings and in public buildings or buildings used by the public.
Installation
All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with
careful observation of the indications provided in the Manuals / Instruction sheets supplied with those products.
Wires
Cut o the power supply before carrying out any maintenance procedures.
Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system
manual.
We advise against running the system wires through the same duct as the power cables (230V or higher).
Safe usage
To ensure Comelit products are used safely:
• carefully observe the indications provided in the Manuals / Instruction sheets
• make sure the system created using Comelit products has not been tampered with / damaged.
Maintenance
Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance
with the indications provided in the Manuals / Instruction sheets.
Any repair work must be carried out
• for the products themselves, exclusively by Comelit Group S.p.A.,
• for systems, by qualified technical personnel.
Disclaimer
Comelit Group S.p.A. does not assume any responsibility for
• any usage other than the intended use
• non-observance of the indications and warnings contained in this Manual / Instruction sheet.
Comelit Group S.p.A. nonetheless reserves the right to change the information provided in this Manual / Instruction
sheet at any time and without prior notice.
2

Art. 1414 is used to branch a second riser from the outgoing BUS line from the mixer. It can also act as line protection (only
for SBTOP systems). The device can be used with Building kit and SBTOP systems and, as it is powered by the 2-wire bus, it
does not need any additional power supply.
MAX. 100 users can be connected to each Mixer Art. 4888C, regardless of the number of Art. 1414 used.
Description
1. JP2 jumper to reinstate the line after a short circuit.
2. DL1 isolated line signalling LED (protection active).
3. JP3 jumper for setting of connection distances. For line protection function only.
4. LM LM branch riser output terminals.
5. JP4 JP1 jumper for activating/deactivating line protection function.
6. L OUT L OUT line output.
L IN L IN line input.
1.
6.
2.
3.
4.
5.
Technical features
MAIN FEATURES
Product height (mm) 85
Product width (mm) 66
Product depth (mm) 37
Operating temperature (°C) -5÷40
RH max operating humidity (%) 25÷75
DIN rail mounted Yes
DIN modules (no.) 4
Power supply voltage (V) Bus line
GENERAL DATA
Type of finish Plastic
Product colour White
COMPATIBILITY
Simplebus Top audio/video system Yes
Building Kit audio/video system Yes
3

Connection
1414
BUS LINE OUTPUT
BUS LINE INPUT / 4888C / 1210
L
M
L
M
L
OUT
L
OUT
L
IN
L
IN
BRANCH RISER
OUTPUT
TERMINALS
Operation and Programming
fJumpers JP1 and JP4 must be removed in order to activate this function.
The line protection function allows the branch line to be automatically isolated in case of short circuit. If this occurs, LED DL1
lights up to signal the fault (Fig. A). To reinstate the line, after eliminating the problem it is necessary to move jumper JP2 to
position B until the LED (Fig. B) goes o, then move the jumper to position A (Fig. C).
A B C
Line protection function
In Building Kit systems, it is only compatible for the “riser branch” function (not “line protection”).
4

Depending on the type of cable used and the distance between the furthest riser branch internal unit and the mixer, jumper
JP3 must be arranged according to the settings given in Table 1.
For all other distances refer to: SBTOP audio/video system.
Jumper JP3 setting for line protection function
Table 1
Max. distance between Mixer
and furthest internal unit. Position of jumper JP3
D
Comelit Art.4577/4579 1 mm² (Ø 1,2 mm AWG 17) 200 m (650 feet) Pos A
1,5 mm² (Ø 1,4 mm AWG 15) 150 m (495 feet) Pos A
1 mm² (Ø 1,2 mm AWG 17)

120 m (390 feet) Pos A
0,28 mm² (Ø 0,6 mm AWG 23) 70 m (225 feet) Pos A
100 m (325 feet) Pos B
UTP5 cat. 5 0,2 mm² (Ø 0,5 mm AWG 24) 50 m (160 feet) Pos A
80 m (260 feet) Pos B
0,5 mm² (Ø 0,8 mm AWG 20) 80 m (260 feet) Pos A
120 m (390 feet) Pos B
Supplied with Art. 1414
4888C
1414
1214/2C
1216
1214/2C
1216
1214/2C
1216
1214/2C
1214/2C
1216
1414 1414 1414
6700W
6701W
6701B
+6710
6700W/BM
6701W/BM
6701B/BM
6801W
6801W/BM
6601W
6601W/BM
6721W
6721W/BM
+6710
6721W
6721W/BM
+6710
System performance and layouts
For further information of system performance and to view installation layouts, click on the system type that best meets your
requirements:
• Building Kit audio/video system for the creation of audio-video systems for small apartment blocks.
• SBTOP audio/video system for the creation of audio-video systems for residential complexes.
5

www.comelitgroup.com
Via Don Arrigoni, 5 - 24020 Rovetta (BG) - Italy
5ª edizione 08/2018 cod. 2G40002084
CERTIFIED MANAGEMENT SYSTEMS