Comelit Simplebus1 Ultra UT1020 User manual

FREE DOWNLOAD
MYCOMELIT, L'APP PER IL PROFESSIONISTA
MYCOMELIT: THE APP FOR PROFESSIONALS
EN
TECHNICAL
MANUAL
Ultra Simplebus1 audio/video module
art. UT1020, UT1020B, UT1020W
Ultra Simplebus1 remote camera audio module
art. UT1010VC, UT1010VCB, UT1010VCW
MYCOMELIT: THE APP FOR PROFESSIONALS

2
Warning
Intended use
This Comelit product is designed and manufactured for use in the creation of audio and video communication systems in residential,
commercial, industrial and public buildings.
Installation
All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with careful
observation of the indications provided in the Manuals / Instruction sheets supplied with those products. The product must be installed
to the highest standards.
Wires
Disconnect the power supply before carrying out any operations on the wiring.
Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system manual.
We advise against running the system wires through the same duct as power cables (230V or higher).
Safe usage
To ensure Comelit products are used safely:
• carefully observe the indications provided in the Manuals / Instruction sheets,
• make sure the system created using Comelit products has not been tampered with / damaged.
Maintenance
Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance with the
indications provided in the Manuals / Instruction sheets.
Any repairs must be carried out:
• for the products themselves, exclusively by Comelit Group S.p.A.,
• for the systems, by qualified technical personnel.
Do not use alcohol or aggressive products for cleaning purposes.
Disclaimer
Comelit Group S.p.A. does not assume any responsibility for
• any purpose other than the intended use,
• failure to observe the indications and warnings contained in this Manual / Instruction sheet.
Comelit Group S.p.A. reserves the right to change the information provided in this Manual / Instruction Sheet at any time and without
prior notice.
Directives
The manufacturer, Comelit Group S.p.A., hereby declares that this equipment conforms to the applicable directives. The full
EU conformity declaration is available on the web page for the product.
In accordance with art. 26 of Italian Legislative Decree dated 14th March 2014, no. 49 “Implementation of directive 2012/19/
EU on Waste Electrical and Electronic Equipment (WEEE)”, the “crossed-out wheelie bin” symbol indicates that at the end of
its useful life, this product must be separated from other waste before collection for disposal. The user should therefore take
the exhausted appliance to suitable local collection centres for waste electrical and electronic products. As an alternative to
handling this process yourself, you can take the appliance to your local equipment dealer when purchasing a new equivalent
product. Electronics dealership businesses covering an area of 400 m² are also obliged to accept waste electronic products
smaller than 25 cm for disposal, without any obligation to purchase. Suitable separated waste collection for the subsequent
reuse of the appliance sent for recycling, processing and environmentally conscious disposal helps to avoid potential
negative eects on the environment and human health, and encourages the reuse and recycling of the materials used in the
construction of the appliance.

3
Table of contents
Warning ............................................................................................ 2
Description....................................................................................... 4
UT1020 ......................................................................................................4
UT1010VC .................................................................................................4
Installation notes (art. UT1020) ...................................................... 6
Technical specifications ................................................................. 7
Art. UT1020 ...............................................................................................7
Art. UT1010VC ..........................................................................................8
Installation........................................................................................ 9
Flush-mounted installation composition table....................................9
Surface-mounted installation composition table................................9
Flush-mounted installation........................................................... 10
Removing nameplates (2A) / module (2B)............................................11
Installation with side-by-side boxes.....................................................12
Wall-mounted installation............................................................. 13
Removing nameplates (2A) / module (2B)............................................14
Installation with side-by-side boxes.....................................................15
Connections................................................................................... 16
Standard connection .............................................................................16
Variants ...................................................................................................16
Remote camera connection (art. UT1010VC only)..............................17
Module connection........................................................................ 18
Connection of button modules art. UT9200 .....................................18
Connection of Touchscreen module art. UT9270.............................18
Connection of number keypad module art. UT9279M .....................19
Connecting digital call module art. UT9260M ..................................19
Programming ................................................................................. 20
Configuring the button type to maintain during normal operation
(single/dual) ............................................................................................20
Addressing button modules..................................................................20
Programming user codes ......................................................................20
Programming consecutive smart user codes............................. 21
Programming specific user codes............................................... 22
Special programming via DIP Switch .......................................... 23
Special programming table...................................................................24
Twilight sensor............................................................................... 26
Camera LED lighting and button backlighting management.............26
Checking twilight sensor operation .....................................................27
Adjusting the brightness of the button LEDs and the camera light ..28
Light-me function .......................................................................... 29
Light-me function behaviour on the basis of the LED backlighting
mode........................................................................................................29
Replacing the audio/video module with programming restore
backup............................................................................................ 30
Configuring via PC......................................................................... 31
Errors and indications................................................................... 31
System functions........................................................................... 32
Operating distances...............................................................................33
Maximum system expansion.................................................................34
Maximum expansion per apartment.....................................................34
Wiring diagrams............................................................................. 35
System performance and layouts ................................................ 36
Table of user codes ....................................................................... 37

4
Description
UT1020
Audio/video module for Ultra entrance panel, Simplebus1 system. To be used in systems with power supply unit art.
1595 and art. 4888C. Wide-angle colour video camera (field of vision: 120° horizontal, 90° vertical)
UT1010VC
Audio module designed for connection of an analogue remote camera with PAL standard for Ultra entrance panel,
Simplebus1 system. To be used in systems with power supply unit art. 1595 and art. 4888C.
Easy to install and simple to configure, thanks to the smart programming of call buttons.
Twilight sensor for automatic nameplate backlighting switch-off during daylight hours.
Omnidirectional digital microphone and double loudspeaker for high-fidelity audio.
Audio-visual indications for disabled individuals assistance request can be activated via programming.
Facility for 2 call buttons. To be finished with cap, single button or dual button made using aluminium or professional
grade plastic treated to prevent yellowing and dulling.
Adjustment and programming can take place without removing the module.
Dimensions: 100 x 90 x 35 mm.
ULTRA: the new and most technologically advanced entrance panel offering maximum ease of installation.
Available in flush-mounted or surface-mounted variants (protrusion from the wall just 10 mm and 35 mm respectively),
in silver (art. UT1020 and UT1010VC), black RAL9005 (art. UT1020B and UT1010VCB) and white (art. UT1020W and
UT1010VCW).
To make full use of the available functions, ALL modules making up the external
entrance panel must be updated to the latest firmware version, which is available to
download from the website pro.comelitgroup.com
Use ViP Manager software, available to download from the website
pro.comelitgroup.com, to carry out the update.

5
1
2
UP
Art. UT1010VC 18.
UP
13. 14. 15.3. 4. 5. 6. 7.
9.10.11. 12. 8.
1. 2. 2.
16.
17.
1. Indicator LEDs
call sent (green) / system busy (red)
lock-release enabled
call in progress
2. Loudspeakers
3. Colour video camera (with art. UT1020 only)
4. Speaker volume control
5. S1 Button programming selector
6. S2 Special programming selector
7. Micro USB input for programming via computer
8. Twilight sensor
9. Addressing and programming Dip Switches
10. Microphone volume control
11. Programming confirmation button
12. Digital microphone
Use screwdriver supplied
13. Terminal block for connection:
RTE programmable RTE (local lock-release
input) or DO input (door open indication)
GND RTE or DO input reference negative
SE electric door lock reference negative
NO NC COM relay contacts
V- V+ power supply
LL bus line connection
14. Ethernet terminal block, only for use in case of additional
modules with LAN
15. Connector for additional modules with LAN
16. 17. Connector for additional module connection
18. Remote camera connection (with art. UT1010VC only):
in flush-mounted installations, use the terminal;
in surface-mounted installations, solder the wires
and use the heat-shrink sheath.

6
Installation notes (art. UT1020)
165 cm
100 cm
215 cm
90°
50 cm
100 cm
180 cm
130 cm
90°
50 cm
150 cm
100 cm
200 cm
90°
50 cm
50 cm
175 cm
120°
The camera must not be installed in front of light sources, or in places where the filmed subject is against the light. In
dim environments, we recommend additional lighting is provided.

7
Technical specifications
Art. UT1020
GENERAL DATA
Type Modular
Product height (mm) 90
Product width (mm) 100
Product depth (mm) 35
Product weight (g) 275
Product colour Black RAL9005, Transparent, Aluminium (art.UT1020), black (art.UT1020B), white
(art.UT1020W)
Coating material type Polycarbonate, Aluminium alloy
Flush mounting Yes, with specific accessory
Surface mounting Yes, with specific accessory
COMPATIBLE SYSTEMS
Simplebus 2 audio/video with power supply unit
art. 4888C Yes
AUDIO SPECIFICATIONS
Microphone MEMS digital audio sensor, omnidirectional
Loudspeaker 28 mm (Ø), 8 Ohm, 1W (2)
Technologies implemented Full-Duplex
CAMERA FEATURES
Camera Colour
Sensor type 1/3" CMOS
Lens (mm) 1.79
Viewing angle (H x V - °) 120 x 90
Sensitivity (lux) 0.45
Resolution (H x V - pixel) 1288 x 968
ELECTRICAL SPECIFICATIONS
Type of power supply External power supply
Power supply voltage 33 VDC
Absorption in standby (W) 1.5
Maximum absorption (W) 6
HARDWARE SPECIFICATIONS
Call type Buttons
Type of buttons Mechanical
Number of buttons (no.) 2
Backlighting colour White, O
Terminals L L V+ V- COM NC NO SE GND RTE TX- TX+ RX- RX+
Number of inputs (no.) 1
Number of outputs (no.) 2
Output type Relay (C-NO-NC, 4A@12-24 VAC/VDC, inrush 10A), SE: 4A unlock pulse, maintenance
current 200 mA for 12 VAC/DC door locks (maximum impedance 18 Ohm)
Communication port Micro-USB
Twilight sensor Yes
SETTINGS
Loudspeaker volume Yes
Mic volume Yes
Backlighting brightness Yes
PROGRAMMING MODE
Manual (via Dip Switch) Yes
ViP Manager software Yes
ENVIRONMENTAL AND CONFORMITY
SPECIFICATIONS
IP protection rating (when installed) IP65
IK anti-vandal protection rating IK08
Operating temperature (°C) -25 to 55
Operating humidity (max RH - %) 25 to 95
Environmental class IV
Conformity and Certifications RoHS II - 2011/65/EU (EN IEC 63000:2018), EMC 2014/30/EU (EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011)
MAIN FUNCTIONS
Lock-release Yes
Number of auxiliary relays (no.) 1
Input for local lock-release button Yes
Input for door open indication Yes
System status visual indications Yes
System status audio indications Yes
System status voice synthesis Yes

8
Art. UT1010VC
GENERAL DATA
Type Modular
Product height (mm) 90
Product width (mm) 100
Product depth (mm) 35
Product weight (g) 275
Product colour Black RAL9005, Transparent, Aluminium (art.UT1010VC), black (art.UT1010VCB),
white (art.UT1010VCW)
Coating material type Polycarbonate, Aluminium alloy
Flush mounting Yes, with specific accessory
Surface mounting Yes, with specific accessory
COMPATIBLE SYSTEMS
Simplebus 2 audio/video with power supply unit
art. 4888C Yes
AUDIO SPECIFICATIONS
Microphone MEMS digital audio sensor, omnidirectional
Loudspeaker 28 mm (Ø), 8 Ohm, 1W (2)
ELECTRICAL SPECIFICATIONS
Type of power supply External power supply
Power supply voltage 33 VDC
Absorption in standby (W) 1.5
Maximum absorption (W) 4
HARDWARE SPECIFICATIONS
Call type Buttons
Type of buttons Mechanical
Number of buttons (no.) 2
Backlighting colour White, O
Terminals L L V+ V- COM NC NO SE GND RTE TX- TX+ RX- RX+
Number of inputs (no.) 1
Number of outputs (no.) 2
Output type
Relay (C-NO-NC, 4A@12-24 VAC/VDC, inrush 10A), SE: 4A unlock pulse,
maintenance current 200 mA for 12 VAC/DC door locks (maximum impedance 18
Ohm)
Communication port Micro-USB
Twilight sensor Yes
SETTINGS
Loudspeaker volume Yes
Mic volume Yes
Backlighting brightness Yes
PROGRAMMING MODE
Manual (via Dip Switch) Yes
ViP Manager software Yes
ENVIRONMENTAL AND COMPLIANCE
SPECIFICATIONS
IP protection rating (when installed) IP65
IK anti-vandal protection rating IK08
Operating temperature (°C) -25 to 55
Operating humidity (max RH - %) 25 to 95
Environmental class IV
Conformity and Certifications RoHS II - 2011/65/EU (EN IEC 63000:2018), EMC 2014/30/EU (EN 61000-6-1:2007,
EN 61000-6-3:2007+A1:2011)
MAIN FUNCTIONS
Lock-release Yes
Number of auxiliary relays (no.) 1
Input for local lock-release button Yes
Input for door open indication Yes
System status visual indications Yes
System status audio indications Yes
System status voice synthesis Yes

9
Rain shield
UT9191
UT9191B
UT9191W UT9192
UT9192B
UT9192W
UT9194H
UT9193
UT9193B
UT9193W
UT9196 UT9199
UT9194
UT9194B
UT9194W
UT9198
Housing/frame
UT9171
UT9171B
UT9171W UT9172
UT9172B
UT9172W
UT9174H
UT9173
UT9173B
UT9173W
UT9176 UT9179
UT9174
UT9174B
UT9174W
UT9178
Installation
Optional
Flush-mounted installation composition table
Surface-mounted installation composition table
A = Rain shield
B = Surface-mounted housing with frame
A = Flush-mounted box
B = Rain shield
C = Flush-mounted module holder with finishing
frame
Flush-mounted box
3110/1
3110/1A 3110/2
3110/2A 3110/3
3110/3A 3110/4
3110/4A
Rain shield
UT9181
UT9181B
UT9181W UT9182
UT9182B
UT9182W
UT9184H
UT9183
UT9183B
UT9183W
UT9186 UT9189
UT9184
UT9184B
UT9184W
UT9188
Module holder/finishing frame
UT9161
UT9161B
UT9161W UT9162
UT9162B
UT9162W UT9163
UT9163B
UT9163W UT9164
UT9164B
UT9164W
The entrance panel is available in flush-mounted or surface-mounted variants:

10
2
1
2
UP
53 4
1
Flush-mounted installation
Optional
BLACK
Optional
RED

11
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
2
1
11 12
1
2
10
CLACK!
CLACK!
1
2
3CLACK!
8
CLACK!
CLACK!
CLACK!
1
2
3
7
1
2
3
1
2
3
1
2A
1
3
2
4
2B
Removing nameplates (2A) / module (2B)
CLOSE
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the pre-
cut sheets (C) available in our catalogue (art. UT9110 ).
Custom engraved Full Metal Ultra nameplates are available
on request. Find out how:
https://pro.comelitgroup.com/customised-nameplates-for-
ultra-entrance-panel
Kit art. UT9110 contains 5 sheets of pre-cut labels for nameplates and 1 sheet for the information module.
The sheets are made using Yupo paper which oers the ultimate transparency and resistance to atmospheric agents over time.
To print the labels, use the editable .pdf file which is available to download free of charge from the website pro.comelitgroup.com.

12
Installation with side-by-side boxes
Before installing the boxes in the wall, fit the spacers.
RED
BLACK

13
2
UP
53 4
UP
1
2
3
1
Wall-mounted installation
Optional
BLACK
RED
Optional

14
6
1
A
B
C
C
2
+ Art. UT9110
MAX 0,2 mm
MAX 0,2 mm
9
2
1
11 12
1
2
10
CLACK!
CLACK!
1
2
CLACK!
3
8
CLACK!
CLACK!
1
2
CLACK!
3
7
1
2
3
1
2
1
3
2A
1
3
2
4
2B
Removing nameplates (2A) / module (2B)
CLOSE
The button has a nameplate which can be written on (A);
alternatively, an adhesive label can be applied (B).
The total thickness of the nameplate + adhesive label
must not exceed 0.2 mm.
You can visit the website pro.comelitgroup.com to download
the PDF to print the entrance panel name cards, using the pre-
cut sheets (C) available in our catalogue (art. UT9110 ).
Custom engraved Full Metal Ultra nameplates are available
on request. Find out how:
https://pro.comelitgroup.com/customised-nameplates-for-
ultra-entrance-panel
Kit art. UT9110 contains 5 sheets of pre-cut labels for nameplates and 1 sheet for the information module.
The sheets are made using Yupo paper which oers the ultimate transparency and resistance to atmospheric agents over time.
To print the labels, use the editable .pdf file which is available to download free of charge from the website pro.comelitgroup.com.

15
Installation with side-by-side boxes
RED
BLACK

16
4888C
E
T
R
GND
SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
12 VAC/VDC
18 Ω MAX
UT1020 UT1010VC
E
T
R
GND SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
4888C
ON
1 2 3 4 6 75 8
120-230 V
-
+
1595 4888C
10A MAX
AC-DC
12V/24V
E
T
R
SE NO NC
C
O
M
LL
+
VV
-
GND
10A MAX
AC-DC
12V/24V
UT1020 UT1010VCUT1020 UT1010VC
Connections
Standard connection
Max 20 m. Local door-opener button.
“C.NC.NO relay activation on actuator command:
2 sec”
fSet DIP switch 8 to ON permanently (as shown in
the figure)
Max 20 m. Local door-opener button.
Variants
Variant for using the outdoor entrance panel relay Variant for using a safety door lock

17
4888C
UP
ROSSO
NERO
V
S
E
T
R
GND
SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
~
SV
SV
ROSSO NERO
12 VAC/VDC
18 Ω MAX
UT1010VC
Remote camera connection (art. UT1010VC only)
Max 20 m. Local door-opener button.
RED
BLACK
RED BLACK

18
UP
NERO
ROSSO
UT9200
4888C
E
T
R
GND
SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
UT1020 UT1010VC
12 VAC/VDC
18 Ω MAX
4888C
E
T
R
GND
SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
UT9270
UT1020 UT1010VC
12 VAC/VDC
18 Ω MAX
Module connection
Connection of button modules art. UT9200
Connection of Touchscreen module art. UT9270
Max 20 m. Local door-opener button.
Max 19 with UT1020.
Max 24 with UT1010VC.
Max 20 m. Local door-opener button.
RED
BLACK

19
4888C
E
T
R
GND SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
UT9279M
UT1020 UT1010VC
12 VAC/VDC
18 Ω MAX
4888C
E
T
R
GND SE NO NC
C
O
M
LL
+
VV
-
120-230 V
-
+
1595
UT9260M
UT1020
12 VAC/VDC
18 Ω MAX
UT1010VC
Connection of number keypad module art. UT9279M
Connecting digital call module art. UT9260M
Max 20 m. Local door-opener button.
Max 20 m. Local door-opener button.

20
1
ON
2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
ON
1 2 3 4 65
1
2
4
3
5
65
default
65
ON
OFF
1
ON
2 3 4 65
8765 8765
default
ON
OFF
Programming
For correct programming, follow the instructions below in order
I. Configure button type
II. Address button modules
III. Program user codes
code
DIP ON
1112 3,4 23 1,2,3,5
2213 1,3,4 24 4,5
31,2 14 2,3,4 25 1,4,5
4315 1,2,3,4 26 2,4,5
51,3 16 527 1,2,4,5
62,3 17 1,5 28 3,4,5
71,2,3 18 2,5 29 1,3,4,5
8419 1,2,5 30 2,3,4,5
91,4 20 3,5 31 1,2,3,4,5
10 2,4 21 1,3,5
11 1,2,4 22 2,3,5
TAB. A
Configuring the button type to maintain during normal operation (single/dual)
I
Addressing button modules
DIP 1-5: addressing call button module (see TAB. A)
Addressing call button modules means that, in the event they are replaced, it is not necessary to reprogram the user
codes associated with the buttons. All you need to do is assign the same address as before to the new module.
II
Programming user codes
There are 2 programming methods:
• Programming consecutive smart user codes allows quick programming of buttons with consecutive user codes
(e.g.: 1, 2, 3, 4)
• Programming specific user codes allows programming of specific user codes (e.g.: 25, 37, 70, 58)
III
DIP 6: configuring button type:
Single button (DIP6 ON).
Dual button (DIP6 OFF, default).
DIP 6: configuring button type:
Single button (DIP6 ON).
Dual button (DIP6 OFF, default).