Comelit Mini 6721W User manual

EN
Passion.Technology.Design.
TECHNICAL
MANUAL
Simplebus2 Mini hands-free door entry monitor
Art. 6721W - Art. 6721W/BM

2
Description....................................................................................... 3
Legend: buttons and indicator LEDs......................................................4
Pressing and holding keys (Disabled by default from firmware
version 2.2.0)............................................................................... 4
Automatic lock-release on receipt of call (Doctor mode) ....................4
Automatic Answer (Hands-Free function)..............................................4
Self Activation...........................................................................................4
Technical specifications ................................................................. 5
Installation........................................................................................ 6
Removing/Fitting the Terminal................................................................7
Connections..................................................................................... 7
Settings ............................................................................................ 7
Main and secondary door entry monitors .............................................7
Button configuration ....................................................................... 8
Basic configuration..................................................................................8
Legend ................................................................................................8
Advanced configuration ..........................................................................9
Intercom call .......................................................................................9
Introduction .................................................................................9
General intercom call: button programming ...............................9
Intercom call to selective address: button programming ............9
Selective intercom address .......................................................10
Assigning selective address ......................................................10
Deleting the selective address of the door entry monitor..........10
Generic actuator, coded actuator.....................................................10
Generic actuator: button programming ....................................10
Coded actuator: button programming......................................11
Other functions: button programming ..............................................11
Programming range ..........................................................................11
Changing the ringtone ......................................................................12
Programming reset ...........................................................................12
Addressing table............................................................................ 13
System performance and layouts ................................................ 13
Warning
Intended use
This Comelit product has been designed and manufactured for use in the creation of audio and video communication systems in residential,
commercial, industrial and public buildings.
Installation
All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with careful observation of
the indications provided in the Manuals / Instruction sheets supplied with those products.
Wires
Disconnect the power supply before carrying out any operations on the wiring.
Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system manual.
We advise against running the system wires through the same duct as power cables (230V or higher).
Safe usage
To ensure Comelit products are used safely:
• carefully observe the indications provided in the Manuals / Instruction sheets,
• make sure the system created using Comelit products has not been tampered with / damaged.
Service
Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance with the indications
provided in the Manuals / Instruction sheets.
Any repairs must be carried out:
• for the products themselves, exclusively by Comelit Group S.p.A.,
• for the systems, by qualified technical personnel.
Disclaimer
Comelit Group S.p.A. does not assume any responsibility for
• any usage other than the intended use
• failure to observe the indications and warnings contained in this manual.
Comelit Group S.p.A. reserves the right to change the information provided in this manual at any time and without prior notice.
Table of contents

3
Description
6721W
Wall-mounted hands-free monitor with full-duplex audio and 4.3” / 16:9 colour screen. Allows brightness level and ringtone volume adjustment;
the ringtone can be customised by selecting one of several dierent melodies. With 5 touch-sensitive buttons with LED backlighting for audio
operation, lock-release, self activation, switchboard call and Privacy function, plus a door status indicator LED. Floor door call management
as standard. Option of adding 3 additional buttons with accessory art. 6734W. Complete with 2 dip-switches with 8 positions for user code
programming and button programming. The backplate for wall mounting or domestic series box installation and the riser distribution terminal art.
1214/2C are included. The monitor can only be used in Simplebus2 systems. Dimensions (L x H x D): 115x160x22 mm.
6721W/BM
Wall-mounted hands-free monitor with full-duplex audio and 4.3” / 16:9 colour screen, plus hearing induction loop. Allows colour, contrast and
ringtone volume adjustment; the ringtone can be customised by selecting one of several dierent melodies. With 5 touch-sensitive buttons
with LED backlighting for audio operation, lock-release, self activation, switchboard call and Privacy function, plus a door status indicator LED.
Floor door call management as standard. Option of adding 3 additional buttons with accessory art. 6734W. Complete with 2 dip-switches with
8 positions for user code programming and button programming. The monitor can only be used in 2-wire Simplebus2 systems. Dimensions (L x
H x D): 115x160x22 mm
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
12.
11.
13.
14.
1. 4.3’’ 16:9 LCD screen
2. Speaker and audio activation button
3. Touch-sensitive buttons
4. Loudspeaker volume control
fTo increase the value, turn clockwise
5. Brightness control
fTo increase the value, turn clockwise
6. Call volume adjustment (high - medium - low)
7. S1 DIP-switches Microswitches for assigning user code according to “Addressing table” on page 13)
8. S2 DIP-switches Multifunctional microswitches
DIP 1-2-3-4 for button function programming
DIP 5-6 for access to programming
DIP 7 for power supply voltage management. Default ON
S2 DIP 7 must always be set to ON, even in systems with 4888C and 4888CU (as in the factory settings).
DIP 8 for setting main and secondary door entry monitor. Paragraph “Main and secondary door entry monitors” on page 7
9. Factory setting. Do not change!
10. Factory setting. Do not change!
11. CV 5 Jumper for video closure. In systems with more than one monitor connected in cascade, only the monitor furthest away must have
CV5 closed.
12. Pin for securing terminal block
13. Space for housing additional button expansion (Art. 6734W)
14. Terminal block for system connection
L L Bus line connection terminals
CFP1 CFP2 Floor door call input

4
Legend: buttons and indicator LEDs
fPress the desired button once to activate the associated function.
Wait for approximately 1 sec. before pressing the same button again. Pressing the same button several times in quick succession will
cancel the command.
Description of buttons Indicator LED description
AUDIO
fPress the button to answer an incoming call.
Flashing LED: incoming call
Steady LED in call: in communication
Steady LED in stand-by: Automatic Answer mode enabled
LOCK-RELEASE (default)*
fPress the key to activate the corresponding door lock.
Flashing LED: incoming call
1 flash after pressing button: door open confirmed
Slow flashing: door open
ACTUATOR (default)*
fPress the key to activate the corresponding relay. Flashing LED: device in programming mode
4 flashes: system busy
Steady LED: silent mode enabled
3 flashes every 5 sec.: Automatic Lock-release on receipt of
call function enabled
SELF ACTIVATION (default)*
fPress the key to access real-time viewing of the camera for
the external unit.
RINGTONE IN SILENT MODE (Privacy)
fPress the key to enable silencing of the ringtone on receipt
of a call from the external unit and from the switchboard.
ADDITIONAL BUTTONS*
Art. 6734W Additional buttons kit - can be purchased
separately.
Other functions that can be programmed:
• AUTOMATIC LOCK-RELEASE ON RECEIPT OF CALL (Doctor mode)
See paragraph “Pressing and holding keys on page 4
• AUTOMATIC ANSWER (Hands-Free function)
See paragraph “Pressing and holding keys on page 4
• INTERCOM
Call from one internal unit to one or more internal units.
• CALL TO A MAIN OR SECONDARY SWITCHBOARD.
• PRIORITY CALL TO SWITCHBOARD (“PAN”)
• CALL TO CARETAKER DOOR-ENTRY PHONE
Pressing and holding keys (Disabled by default from firmware version 2.2.0)
Pressing and holding keys adds further functions to the door entry monitor.
Carry out the procedure described below to enable - or disable, depending on the factory setting - the press and hold feature:
√Door entry monitor in standby.
1. Take note of the S2 DIP-switch settings.
2. Enter programming mode by setting S2 DIP-switches 1, 3, 5 to ON.
» the LED flashes
3. Press to enable (or press to disable).
4. Make sure the key flashes 4 times and the confirmation tone is emitted.
5. Restore the initial configuration of the S2 DIP-switches.
» LED switches off
Once the procedure is complete, you will be able to enable the following functions:
Automatic lock-release on receipt of call (Doctor mode)
Automatic activation of the Lock-release relay on receipt of a call originating from the external unit.
fPress and hold (4 sec.) the programmed button to enable/disable the function.
Automatic Answer (Hands-Free function)
Automatic audio opening on receipt of a call.
fPress and hold (4 sec.) the audio activation button to enable/disable the function.
Self Activation
fPress and hold (4 sec.) the programmed button to disable the function. (Enabled by default).
* To edit the default settings, see paragraph
“Button configuration” on page 8.

5
Technical specifications
GENERAL DATA 6721W 6721W/BM
Product height (mm) 160 160
Product width (mm) 115 115
Product depth (mm) 22 22
Product weight (g) 500 500
Product colour White RAL9003 White RAL9003
Material ABS ABS
Surface mounting Yes Yes
Desk base mounting Yes, with specific accessory Yes, with specific accessory
COMPATIBLE SYSTEMS
Simplebus2 audio/video with power supply unit art. 4888C Yes Yes
Simplebus 2 audio/video with power supply unit art.
1210/1210A
Yes Yes
Simplebus 2 audio/video kit with power supply unit art. 1209 Yes Yes
DISPLAY SPECIFICATIONS
Display size (inches) 4.3” 4.3”
Aspect ratio 16:9 16:9
Resolution (pixels) 480 x 272 480 x 272
AUDIO SPECIFICATIONS
Magnetic induction function No Yes
Microphone 6 mm (Ø), Omnidirectional 6 mm (Ø), Omnidirectional
Loudspeaker 36mm (Ø), 40 Ohm, 1W 36mm (Ø), 40 Ohm, 1W
ELECTRICAL SPECIFICATIONS
Type of power supply Power supply via video entry bus Power supply via video entry bus
Power supply voltage 22 to 34 VDC (Bus) 22 to 34 VDC (Bus)
Minimum absorption (W) 0.05 0.05
Maximum absorption (W) 8.8 8.8
HARDWARE CHARACTERISTICS
Type of buttons Capacitive Capacitive
No. of programmable buttons for additional functions 2 (5 with accessory art. 6734W) 2 (5 with accessory art. 6734W)
Terminals L L CFP1 CFP2 L L CFP1 CFP2
Removable terminals Yes Yes
SETTINGS
Loudspeaker volume Yes Ye s
Mic volume Yes Yes
Ringtone volume Yes Yes
Display brightness Yes Yes
Screen contrast Yes Yes
Screen colour Yes Ye s
ENVIRONMENTAL AND CONFORMITY SPECIFICATIONS
IP protection rating 30 30
Operating temperature (°C) 5 to 40 5 to 40
Operating humidity (max RH - %) 25 to 75 25 to 75
Environmental class I I
Conformity and Certifications RoHS II - 2011/65/EU (EN 50581:2012),
EMC 2014/30/EU (EN 61000-6-
1:2007, EN 61000-6-3:2007+A1:2011)
RoHS II - 2011/65/EU (EN 50581:2012),
EMC 2014/30/EU (EN 61000-6-
1:2007, EN 61000-6-3:2007+A1:2011)
FUNCTIONS
Self Activation Yes Yes
Intercom calls Yes Ye s
Actuator control Yes Ye s
Switchboard call Yes Ye s
Input for floor door call Yes Yes
Automatic lock-release on receipt of call (Doctor) Ye s Yes
Automatic answer (Hands-Free) Yes Yes
Door open indication Yes Yes
Multiple address Yes Ye s
Customisable ringtone Yes Ye s
Alarm call transmission Yes Ye s

6
Installation
1C1B1A
4
32
6
2
1
5
fissaggio
opzionale
115 mm
160 mm
1
2
FACILITATED OPENING

7
Removing/Fitting the Terminal
3
1
2
L L C
F
P
1C
F
P
2
1
2
3
Connections
20 m MAX - Use shielded cable for the
connection and do not route the cables
in the vicinity of heavy inductive loads
or power supply cables (230 V/400 V).
Where multiple door-entry phones or door
entry monitors have the same user code,
connect the CFP button on one only; all the
devices will ring simultaneously.
Main and secondary door entry monitors
Settings
In systems with power supply unit 1209, 1210 or 1210A it is possible to set a maximum of 1 main door entry monitor.
In systems with power supply unit 4888C it is possible to set a maximum of 2 main monitors.
MAIN SECONDARY
S2 DIP 8 OFF ON
S2
1 2 3 4 6 75 8
S2
1 2 3 4 6 75 8
S2
1 2 3 4 6 75 8
S2
1 2 3 4 6 75 8
6721W
6721W/BM
1214/2C
MONTANTE
VIDEOCITOFONICA
MONTANTE
VIDEOCITOFONICA
P
F
C
LL
P
F
C
CHIAMATA
FUORIPORTA
LM
LM
OUT
L
IN
L
IN
L
OUT
L
VIDEO ENTRY SYSTEM
RISER
VIDEO ENTRY SYSTEM
RISER

8
Legend
Button configuration
Basic configuration
AP Lock-release
ACT Actuator
AI Self Activation
CCP Call to main switchboard [not available in KIT systems]
CCS Call to secondary switchboard [not available in KIT systems]
KCaretaker door-entry phone call
PAN Priority call to switchboard [not available in KIT systems]
INT Intercom call (general programmable or to selective address).
Single-family call default for Kit and Simplebus2
INTb Two-family intercom call [for KIT only]
DAutomatic door opening on receipt of call [Doctor mode]
NULL No function
PROG With these S2 DIP-switch settings, the buttons control the programmed functions as in “Advanced configuration” on page 9.
S2 DIP-switches Mini Vivavoce + Art. 6734W
DIP 1 DIP 2 DIP 3 DIP 4
A OFF OFF OFF OFF AP ACT AI CCS D PAN
BON OFF OFF OFF AP CCS AI INT INTb D
COFF ON OFF OFF AP INT AI INTb ACT CCS
DON ON OFF OFF AP ACT CCS CCP PAN K
EOFF OFF ON OFF ACT ACT ACT ACT ACT ACT
FON OFF ON OFF AP INT ACT CCS CCP INTb
GOFF ON ON OFF AP AI D K CCS CCP
HON ON ON OFF AP INTb INT AI INT PAN
IOFF OFF OFF ON AP CCS PAN D AI INTb
JON OFF OFF ON AP K CCS PAN CCP AI
KOFF ON OFF ON AP CCP K PAN ACT INT
LON ON OFF ON AP PAN CCP CCS K ACT
MOFF OFF ON ON AP INTb AI INT ACT D
NON OFF ON ON AP INT INT INT INT INT
POFF ON ON ON NULL NULL NULL NULL NULL NULL
ON ON ON ON PROG
default 
By default the buttons control the functions in row A(“Standard configuration” table).
It is possible to change the default configuration of the buttons by changing the positions of S2 DIP-switches 1-2-3-4 on the rear of the door entry
monitor to one of the combinations (B-P) suggested in the table. All the buttons will change function.

9
If the standard configuration settings (A-P) do not reflect requirements, the buttons can be programmed dierently by carrying out the steps
below.
After programming, set S2 DIP-switches 1-2-3-4 (PROG) to ON. With these DIP-switch settings, the buttons manage the programmed functions.
The buttons that are NOT programmed control the functions in row A (“Standard configuration” table).
Advanced configuration
By "General intercom call" we mean a call from a door-entry phone/door entry monitor to the devices (in the same apartment or another
apartment) identified by the call address for the apartment (user code).
By "Intercom call to selective address" we mean a call from a door-entry phone/door entry monitor to a device (or several) identified by a
specific (selective) address which is dierent from the call address for the apartment (user code).
General and selective intercom calls CANNOT be used together on the same riser!
Intercom call to selective address: button programming
Intercom call
Introduction
General intercom call: button programming
1. Take note of the S1 DIP-switch settings.
2. To enter programming mode, set S2 DIP-switch 6 to ON.
» the LED flashes
S2
3. Refer to the table “Basic configuration” to identify a DIP-switch combination in which the intercom function (INT or INTb) corresponding to the
button you want to program appears, then set the S2 DIP-switches.
Example: For button 1= Intercom (INT) set S2 DIP-switches 1-2-3-4 as specified in row "C" in the "Standard configuration" table.
4. Set the S1 DIP-switches according to the call address of the desired apartment.
See “Addressing table” on page 13
5. Press and release the button to be associated with the function.
» Correct procedure indication: the LED flashes for a few seconds and a confirmation tone sounds.
√when programming using several buttons, continue programming the next key by repeating the process from step 4 onwards.
6. Exit programming mode by setting S2 DIP-switch 6 to OFF.
» LED switches off
S2
7. Set S2 DIP-switches 1-2-3-4 to ON.
8. Return S1 DIP-switches to the original combination.
1. The steps illustrated in paragraph “Assigning a selective address” should be carried out on the devices involved in the intercom call.
2. Take note of the S1 DIP-switch settings.
3. To enter programming mode, set S2 DIP-switch 6 to ON.
» the LED flashes
S2
4. Refer to the table “Basic configuration” to identify a DIP-switch combination in which the intercom function (INT or INTb)
corresponding to the button you want to program appears, then set the S2 DIP-switches.
5. Use the S1 DIP-switches to set the selective address of the device you wish to call. Table B.
For group calls, simultaneously set the desired selective addresses (max. 3) to ON.
6. Press and release the button to be associated with the function.
» Correct procedure indication: the LED flashes for a few seconds and a confirmation tone sounds.
√when programming using several buttons, continue programming the next key by repeating the process from step 5 onwards.
7. Exit programming mode by setting S2 DIP-switch 6 to OFF.
» LED switches off
S2
8. Set S2 DIP-switches 1-2-3-4 to ON.
9. Return S1 DIP-switches to the original combination.

10
Selective intercom address
Deleting the selective address of the door entry monitor
1. 2. 3.
Take note of the
S1, S2 settings and
restore them when
programming is
complete.
Set the DIP-switches as shown in the figure.
S1
S2
x4
x10
OK prog:
KO prog:
x4
x10
OK prog:
KO prog:
Assigning selective address
(Steps only need to be carried out for “Intercom call to selective address” programming)
1. 2. 3. 4.
Take note of the
S1, S2 settings and
restore them when
programming is
complete.
S1: Set an address.
(Table B)
Example: 3
S1
S2: Set the DIP-switches as
shown in the figure.
S2
x4
x10
OK prog:
KO prog:
x4
x10
OK prog:
KO prog:
Assign one of the 8 addresses available in TABLE B to each device involved in the intercom call.
• You can assign the same selective intercom address to a maximum of 3 devices.
TABLE B
Code S1 DIP-switch ON Code S1 DIP-switch ON Code S1 DIP-switch ON
114477
225588
3366
Generic actuator, coded actuator
Generic actuator: button programming
1. Take note of the S1 DIP-switch settings.
2. To enter programming mode, set S2 DIP-switch 6 to ON.
» the LED flashes
S2
3. Refer to the table “Basic configuration” to identify a DIP-switch combination in which the actuator function (ACT) corresponding to the button
you want to program appears, then set the S2 DIP-switches.
4. Set all the S1 DIP-switches to the ON position. S1
5. Press and release the button to be associated with the function.
» Correct procedure indication: the LED flashes for a few seconds and a confirmation tone sounds.
6. Exit programming mode by setting S2 DIP-switch 6 to OFF.
» LED switches off
S2
7. Set S2 DIP-switches 1-2-3-4 to ON.
8. Return S1 DIP-switches to the original combination.

11
Coded actuator: button programming
Other functions: button programming
Programming range
1. 2. 3. 4.
Range minimum address
S1
set code.
“Addressing table”
on page 13
S2
S2
Range maximum address
Enable range
Disable range
Deleting the range
S1 S2
2 sec
Take note of the S2, S1 settings and restore on completion of programming
1. Take note of the S1 DIP-switch settings.
2. To enter programming mode, set S2 DIP-switch 6 to ON.
» the LED flashes
S2
3. Refer to the table “Basic configuration” to identify a DIP-switch combination in which the actuator function (ACT) corresponding to the
button you want to program appears, then set the S2 DIP-switches.
4. Set the S1 DIP-switches with the desired code, according to “Addressing table” on page 13
5. Press and release the button to be associated with the function.
» Correct procedure indication: the LED flashes for a few seconds and a confirmation tone sounds.
6. Exit programming mode by setting S2 DIP-switch 6 to OFF.
» LED switches off
S2
7. Set S2 DIP-switches 1-2-3-4 to ON.
8. Return S1 DIP-switches to the original combination.
1. To enter programming mode, set S2 DIP-switch 6 to ON.
» the LED flashes
S2
2. Refer to the table “Basic configuration” to identify a DIP-switch combination in which the desired functions corresponding to the buttons you
want to program appear, then set the S2 DIP-switches.
Example: For button 4= Self Activation (AI) and button 5 = Call to Secondary Switchboard (CCS), set S2 DIP-switches 1-2-3-4 as specified in row
M in the "Standard configuration" table.
3. Press and release the buttons involved in the change.
» Correct procedure indication: the LED flashes for a few seconds and a confirmation tone sounds.
4. Exit programming mode by setting S2 DIP-switch 6 to OFF.
» LED switches off
S2
5. Set S2 DIP-switches 1-2-3-4 to ON.

12
Changing the ringtone
Programming reset
1. Press and hold for 6 sec.
»a confirmation tone is emitted
»the LED flashes
√the procedure can only take place while the system is in standby; otherwise the LED will flash 4 times to inform the user that the
system is busy
2. Press and release
once (1 confirmation tone is emitted) to change the ringtone for calls from the external entrance panel.
twice (2 confirmation tones are emitted) to change the ringtone for calls from the switchboard.
3 times (3 confirmation tones are emitted) to change the ringtone for intercom calls made from the door entry monitor.
4 times (4 confirmation tones are emitted) to change the floor door call ringtone.
Any further pressing of the button repeats the sequence described above.
3. Press and release to scroll through the available ringtones in sequence.
4. Press the buttonto confirm selection of the last ringtone heard and to exit change ringtone mode.
»a confirmation tone is emitted
»LED switches o
Factory settings:
• Button functions for the S2 DIP-switches 1-2-3-4 combination
• Intercom address absent
• Range function and min./max. addresses absent
• Ringtone reset
• Input IN 1 - IN 2 > LED (default)
• “Automatic answer”, “Automatic door opening on receipt of call” and “Silent” mode disabled
1. 2. 3.
Take note of the
S1, S2 settings and
restore them when
programming is
complete.
Set the DIP-switches as shown in the figure.
S1
S2
x4
x10
OK prog:
KO prog:
x4
x10
OK prog:
KO prog:

www.comelitgroup.com
Via Don Arrigoni, 5 - 24020 Rovetta (BG) - Italy
CERTIFIED MANAGEMENT SYSTEMS
5st edition 01/2021 code 2G40002648
* NOTE: Code 240 is reserved for the porter switchboard
Code
DIP-switch
ON
1131 1,2,3,4,5 61 1,3,4,5,6 91 1,2,4,5,7 121 1,4,5,6,7 151 1,2,3,5,8 181 1,3,5,6,8 211 1,2,5,7,8
2232 662 2,3,4,5,6 92 3,4,5,7 122 2,4,5,6,7 152 4,5,8 182 2,3,5,6,8 212 3,5,7,8
31.2 33 1.6 63 1,2,3,4,5.6 93 1,3,4,5,7 123 1,2,4,5,6.7 153 1,4,5,8 183 1,2,3,5,6.8 213 1,3,5,7,8
4334 2.6 64 794 2,3,4,5,7 124 3,4,5,6,7 154 2,4,5,8 184 4,5,6,8 214 2,3,5,7,8
51.3 35 1,2,6 65 1.7 95 1,2,3,4,5.7 125 1,3,4,5,6.7 155 1,2,4,5,8 185 1,4,5,6,8 215 1,2,3,5,7.8
62.3 36 3.6 66 2.7 96 6.7 126 2,3,4,5,6.7 156 3,4,5,8 186 2,4,5,6,8 216 4,5,7,8
71,2,3 37 1,3,6 67 1,2,7 97 1,6,7 127 1,2,3,4,5,6,7 157 1,3,4,5,8 187 1,2,4,5,6.8 217 1,4,5,7,8
8438 2,3,6 68 3.7 98 2,6,7 128 8158 2,3,4,5,8 188 3,4,5,6,8 218 2,4,5,7,8
91.4 39 1,2,3,6 69 1,3,7 99 1,2,6,7 129 1.8 159 1,2,3,4,5.8 189 1,3,4,5,6.8 219 1,2,4,5,7.8
10 2.4 40 4.6 70 2,3,7 100 3,6,7 130 2.8 160 6.8 190 2,3,4,5,6.8 220 3,4,5,7,8
11 1,2,4 41 1,4,6 71 1,2,3,7 101 1,3,6,7 131 1,2,8 161 1,6,8 191 1,2,3,4,5,6,8 221 1,3,4,5,7.8
12 3.4 42 2,4,6 72 4.7 102 2,3,6,7 132 3.8 162 2,6,8 192 7.8 222 2,3,4,5,7.8
13 1,3,4 43 1,2,4,6 73 1,4,7 103 1,2,3,6,7 133 1,3,8 163 1,2,6,8 193 1,7,8 223 1,2,3,4,5,7,8
14 2,3,4 44 3,4,6 74 2,4,7 104 4,6,7 134 2,3,8 164 3,6,8 194 2,7,8 224 6,7,8
15 1,2,3,4 45 1,3,4,6 75 1,2,4,7 105 1,4,6,7 135 1,2,3,8 165 1,3,6,8 195 1,2,7,8 225 1,6,7,8
16 546 2,3,4,6 76 3,4,7 106 2,4,6,7 136 4.8 166 2,3,6,8 196 3,7,8 226 2,6,7,8
17 1.5 47 1,2,3,4,6 77 1,3,4,7 107 1,2,4,6,7 137 1,4,8 167 1,2,3,6,8 197 1,3,7,8 227 1,2,6,7,8
18 2.5 48 5.6 78 2,3,4,7 108 3,4,6,7 138 2,4,8 168 4,6,8 198 2,3,7,8 228 3,6,7,8
19 1,2,5 49 1,5,6 79 1,2,3,4,7 109 1,3,4,6,7 139 1,2,4,8 169 1,4,6,8 199 1,2,3,7,8 229 1,3,6,7,8
20 3.5 50 2,5,6 80 5.7 110 2,3,4,6,7 140 3,4,8 170 2,4,6,8 200 4,7,8 230 2,3,6,7,8
21 1,3,5 51 1,2,5,6 81 1,5,7 111 1,2,3,4,6.7 141 1,3,4,8 171 1,2,4,6,8 201 1,4,7,8 231 1,2,3,6,7.8
22 2,3,5 52 3,5,6 82 2,5,7 112 5.67 142 2,3,4,8 172 3,4,6,8 202 2,4,7,8 232 4,6,7,8
23 1,2,3,5 53 1,3,5,6 83 1,2,5,7 113 1,5,6,7 143 1,2,3,4,8 173 1,3,4,6,8 203 1,2,4,7,8 233 1,4,6,7,8
24 4.5 54 2,3,5,6 84 3,5,7 114 2,5,6,7 144 5.8 174 2,3,4,6,8 204 3,4,7,8 234 2,4,6,7,8
25 1,4,5 55 1,2,3,5,6 85 1,3,5,7 115 1,2,5,6,7 145 1,5,8 175 1,2,3,4,6.8 205 1,3,4,7,8 235 1,2,4,6,7.8
26 2,4,5 56 4,5,6 86 2,3,5,7 116 3,5,6,7 146 2,5,8 176 5,6,8 206 2,3,4,7,8 236 3,4,6,7,8
27 1,2,4,5 57 1,4,5,6 87 1,2,3,5,7 117 1,3,5,6,7 147 1,2,5,8 177 1,5,6,8 207 1,2,3,4,7.8 237 1,3,4,6,7.8
28 3,4,5 58 2,4,5,6 88 4,5,7 118 2,3,5,6,7 148 3,5,8 178 2,5,6,8 208 5,7,8 238 2,3,4,6,7.8
29 1,3,4,5 59 1,2,4,5,6 89 1,4,5,7 119 1,2,3,5,6.7 149 1,3,5,8 179 1,2,5,6,8 209 1,5,7,8 239 1,2,3,4,6,7,8
30 2,3,4,5 60 3,4,5,6 90 2,4,5,7 120 4,5,6,7 150 2,3,5,8 180 3,5,6,8 210 2,5,7,8 *240 5,6,7,8
Addressing table
System performance and layouts
For further information of system performance and to view installation layouts, click on the system type that best meets your requirements:
• Audio/video kit for the creation of audio-video systems for individual residences
• Building Kit audio/video system for the creation of audio-video systems for small apartment blocks
• SBTOP audio/video system for the creation of audio-video systems for residential complexes.