comfortel ACCELERATOR User manual

#1551 ACCELERATOR PEDESTAL
#1571 ACCELERATOR WALL MOUNT
professional
accelerator
GET STARTED
#1551 PEDESTAL
ACCELERATOR
Professional Processor
ACCELERATOR
4 STAR BASE
PEDESTAL/STAND
comfortel.com.au
owners manual
#1571 WALL MOUNT
WALL ARM

Water poses a serious risk even
when device is switched o, do
not leave device connected to
power supply after use.
OPERATION
GENERAL SAFETY
1. Read carefully and keep these instructions in a
safe place.
2. Use this product only for its intended function and
do not use attachments not recommended by the
manufacturer.
3. Do not use outdoors.
PRECAUTIONS
1. Do not use near water or wet the product. Dry
hands before touching the key pad.
2. Do not stop the accelerator head with your hands
UNLESS it is an emergency
3. Always unplug the until before cleaning
4. No not move or lift the machine from the
accelerator head, as this will damage the unit.
ELECTRICAL APPLIANCES
1. DO NOT allow children to operate in this product.
2. Turn the power o and remove the plug when not in
use or when cleaning.
3. Do not let the power cord get damaged in any way.
4. Keep the power cord away from heat sources.
5. Do not use an extension cord unless the cord
complies with local electrical safety standards.
6. Periodically inspect the power cord for signs of
damage.
7. Do not operate any electrical item with a damaged
power cord.
CONTROLS
1. Start/Stop
2. TIMER
3. TEMPERATURE
4. MODE Perm
5. MODE Treatment
6. MODE Semi-Permanent Colour
7. MODE Colour
8. MODE Drying
9. MODE Manual
10. FUNCTION Cool Fan
11. FUNCTION Hot Fan
12. FUNCTION Rotation
13. POWER On/O
IMPORTANT PLEASE READ THESE SAFETY INSTRUCTIONS
CAUTION: DO NOT USE IF FLEXIBLE CORD IS DAMAGED
ANY REPAIRS TO THIS UNIT MUST BE CONDUCTED BY A QUALIFIED ELECTRICIAN.
TO REPAIR FLEXIBLE CORD, USE TWO CORE SHEATHED CABLE ONLY.
1
2
3
4
5
6
7
8
13
9
12
11
10

OPERATION
OPERATION
1. Adjust the accelerator into position (refer to diagram)
2. Turn POWER on
3. Select a MODE
4. Adjust TEMPERATURE and TIMER if required
5. Push START/STOP to commence treatment
6. During the operation changes can be made to the settings (but not the Mode)
7. To interrupt operation push START/STOP
8. At the end of the programme, an electronic alarm will sound and the fan will activate for 2 minutes. The alarm will
sound again once completed.
9. Please turn o POWER at the end of the operation.
PROGRAMMED SETTINGS
Please note: In all modes, the operator can adjust each setting according to the condition of the hair or preferred method

INSTALLATION & ASSEMBLY: WALLMOUNT
INSTALLATION OF WALL MOUNTED ACCELERATOR
HEIGHT
Recommended height of wall bracket is 1840mm-1950mm from the floor to the bottom of the bracket.
ELECTRICAL
A GPO must be installed within 500mm from the wall bracket.
ELECTRICALS MUST BE INSTALLED BY A
QUALIFIED ELECTRICIAN IN ACCORDANCE
WITH AUSTRALIAN STANDARDS.
AS THE WALL BRACKET ARE SUBJECT T BE
A LARGE LOAD, MAKE SURE THAT THE WALL
PLATE IS INSTALLED CORRECTLY.
IMPORTANTCAUTION
INSTALLATION OF THE WALL BRACKET
Using the wall bracket as the template, drill three holes (10.5mm
diameter/65mm deep)into the wall, bolt the bracket to the wall using
the dynabolts provided.
STEM
BRACKET

INSTALLATION & ASSEMBLY: WALLMOUNT
INSTALLATION OF THE ACCELERATOR HEAD
1. Slide hoop up onto the tube
2. Insert accelerator head onto the wall arm
3. Insert 2 x half moon washers into the slot
4. Slide hoop down to lock washer and head onto arm
5. Tighten grub screw to hold hoop into place
ADJUSTMENT - HEIGHT RESTRICTION
If the machine head hits the ceiling or other furniture, the height can be restricted.
1. Remove cover on arm
2. Turn the adjusting nut to the left as seen below.
3. If turn to the right, accelerator head can go higher
4. Lock tight after adjusting.
TUBE
SLOT
HALF MOON
WASHER
GRUB SCREW
HOOP
TURN
POSITION
SCREW
NUT