Comica CVM-WM100 PLUS User manual

CVM-WM100 PLUS
UHF 1-Trigger-2 Wireless Microphone
User Manual

Foreword
Main Features
. 1-trigger-2,Perfectly Support Two Transmitters and One Receiver Work Simultaneously
. Working Distance Up to 100m (Open Area 100m, 60m in area with obstacle)
. M/S Switch, LCF, 16-levels Adjusted Gain Control, Muting Functions
. AA Batteries and Support External Charging
. Support Real-time Monitor
. Volume Dynamic Monitor
. Adjusted RF Power
. Lattice LCD Display, High Resolution
Thanks for purchasing COMICA WM100 Plus wireless microphone;
WM100 Plus is a wireless microphone with dual-transmitter triggered by one
receiver, with two AA batteries. It utilizes UHF wireless FM technology and LCD
high-resolution lattice screen, 16-level adjustable volume, and is integrated into
LCF(Low cut filter) , Auto IR Channel-match, Stereo / Mono switchable audio
mode, RF signal strength adjustment, MIC/LINE IN input dual selection, Power
monitoring at receiver end, Sound pickup dynamic display, Backlight adjustment
and other functions, at the same time with strong shielding anti-noise
performance, it’s a high-quality microphone to broadcasting level;
To ensure the smooth use and safety of the product, please carefully read this
instruction before using and properly assemble and operate.
Low Cut Filter Muting Mode
16-Levels
Adjusted Gain Control
100m Working
Distance
Lattice LCD
Real-time
Monitor
Support
External Charging
1-Trigger-2 48 Channels
1

Notice
Transmitter should be used more than 10cm from Receiver, when the distance is
less than 10cm, Receiver’s wireless signal receiving part will take protect action to
shut down wireless signal receiving, then audio may be intermittent, which is
normal;
When using auto IR sync, please stay within 30cm, otherwise the signal may be so
weak that the sync will not be successful;
In the case of stereo/mono mode switch, please preset the mode before using to
avoid the transient interference caused by switching during usage;
The antenna will affect the working distance. Please protect the antenna and avoid
any man-made damage;
The working distance will be affected by the surrounding environment. Please try
to keep the environment open without interference during usage, and close the
WIFI of the device itself;
When using this product in a short distance, it is recommended to set RF strength
at ‘LOW’ to reduce the power consumption;
For smartphone shooting, customers must separately purchase a TRS-TRRS
audio converting cable,and pay attention to set the mobile phone mode to 'Flight
Mode' to avoid incoming call interference(It does not support the partial original
recording of android systems, the third-party APP is recommended to be used in
this case);
Please keep this product in dry environment;
Do not expose the device in rain or humid environment, otherwise there will be a
danger of short circuit;
2

Main Parts:
Package Contents
Accessories:
3.5mm Mic Audio Input Cable x 2 pcs
3.5mm-3.5mm Audio Output Cable x 1 pcs
3.5mm-XLR Audio Output Cable x 1 pcs
Belt Clip x 3pcs
Camera mount x 1 pcs
1
1
6
2
7
3
8
4
910
5
2
3
4
510
Wind Muff x 2pcs
USB power input cable x 1 pcs
Portable Bag x 1 pcs
User Manual x 1 pcs
Warranty Card x 1 pcs
6
7
8
9
Lavalier Transmitter (TX) Receiver (RX)
3

Components and Instruction
14
1
2
3
4
5
9
10
12
13
11
6
8
7
Components
Lavalier Transmitter (TX)
Antenna
Working Status Indicator
On-off / Muting Button
SET Function Menu
Function Selection Button -
LINE IN External Input
IR Sensor
Mic External Input
IR Status Indicator
Function Selection Button +
Micro USB Port for External Charging
Belt Clip
1/4 Thread
Battery Tray
1
2
3
4
5
6
7
8
9
10
11
12
13
14
4

1
3
4
5
6
2
10
11
13
14
15
12
7
9
8
Receiver (RX)
Group A Antenna
Group B Antenna
Group A Working Status Indicator
On-Off Button
SET Function Button
Function Selection Button -
3.5mm Audio Input Jack
IR Sensor
3.5mm monitoring Jack
Group B Working Status Indicator
Function Selection Button +
Micro USB Port for External Charging
Belt Clip
1/4 Thread
Battery Tray
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
5

Lavalier
Transmitter
/ Receiver
Power / Muting Button
Long Press
Short Press
Power On / Off
Muting Mode
（the mute function can be
activated only when the
screen is lighted up ）
SET Function Menu
+ Button
- Button
Long Press Enter the function
adjustment menu
Short Press
Short Press
Short Press
1.Confirm the selected
function
2.Exit the function
adjustment menu
Function Adjustment (+)
Function Adjustment (-)
Low cut function:
Appropriately cut the low frequency part of the sound, reduce the noise
of the low frequency part, to make target sound more clean and clear.
Signal strength high/low switching effect:
With high signal strength, the working distance is up to 60-100m,
but high power consumption and short battery life.
With low signal strength, the working distance is up to 30-60m,
but low power consumption and long battery life.
Function Button Instruction
6

Indicator Light Instruction
A IR/RF： Group A Working Status Indicator
B IR/RF： Group B Working Status Indicator
Transmitter
Receiver
RF
A IR/RF
B IR/RF
IR
Green Light Keeps On
Green Light Keeps On
Green Light Keeps On
Red Light Keeps On
Red Light Flicker
Red Light Flicker
Red Light Flicker
Red light keeps on
Green Light Flicker
Normal Recording Status
（This state is only for the
transmitter, when the
channel matches
successfully, the receiver
can pick up the sound）
Muting Mode
Low-power reminder
Channel matches
（No matter the channel
matches or not）
Channel in the match...
（only for IR Sync）
Normal working status after
the channel matches
Channel doesn’t match
Channel in the match...
（only for IR Sync）
Low-power reminder
Group closed
7

Installation and Usage
1.1 Install two AA batteries into the battery tray according to their
positive and negative electrode.
1. Prepare Power Supply
There're two ways of Power Supply, you can optionally choose AA
batteries or External charging:
Preparation Before Usage
(Transmitter Operating Steps same with Receiver)
8

1.2 Charging with External Power
Insert micro USB cable to the USB charging port to realize
external power charging
Micro USB
POWER
9

2.Belt Clip Installation
Please install the belt clip according to the illustration if you require
the way of connection.
10

3.1 Insert the 3.5mm audio input line into MIC socket
3.2 Long press the power button to turn on the transmitter
3. Lavalier Transmitter Installation
11

H
A
Group A
A
3.3 Target the MIC to the audio source and check the working status
according to the volume indicator on the screen
3.4 After the channel matching with the receiver, it can be used
Audio Dynamic Display Bar
570.875MHz
Please refer to screen operation instruction for channel matching.
12

4.1 Connect receiver to your video equipment through the camera
mount
4. Receiver Installation
4.2 Connect one end of the 3.5mm-3.5mm audio OUTPUT cable to the
OUTPUT port of WM200RX and another end to the AUDIO INPUT
port of the camera or camcorder.Insert the headphone into the
3.5mm monitoring port for real-time monitoring and then long press
power button to turn on the receiver.
Most DSLR cameras has 3. 5MM port, if you use the XLR camcorder,
you need to use the 3. 5mm-XLR audio output cable.
13

3.5MM-XLR Audio
Output Cable
3.5mm-3.5mm
Audio Output Cable
3.5mm Audio Output
Monitoring Cable
Please refer to screen operation instruction for channel matching.
4.3 After the channel matching with the receiver, it can be used
14

Mic mode is for Microphone input;
Line in mode is for external audio input, such as smartphone player;
Selecting the corresponding input mode will bring you a better audio
experience.
H
A
Group A
570.875MHz
A
Screen Display and Operation Instruction
Screen Display Instruction
Lavalier Transmitter
Signal Strength High
Signal Strength Low
Group A
Group B
Normal recording
Muting
Muting（Unlocking）
Muting（Locking）
Power Indication
Group A/B
Channel
Group A/B
Audio dynamic display bar Channel Frequency
H
L
15

Operation Instruction
H
A
Group A
A
CH11 570.875MHz
H
A
Group A
A
CH8 570.125MHz
H
A
Group A
A
CH8 570.125MHz
1.1 Long press button to CH setting display page
1.2 Short press button to select the channel
1.Manually Adjust the Channel of Transmitter
1.3 Short press button to confirm
16

2.Group A/B Selection
H
A
A
Group Setting
Group A
H
A
A
Group Setting
Group A
H
A
A
Group Setting
Group B
2.1 Press button to ‘ Group Setting ’ display page
2.2 Long press button to ‘ Group Setting ’ setting page
2.3 Press button to select the group
H
B
B
Group Setting
Group B
2.4 Short press button to confirm
17

H
A
Low Cut Filter
A
OFF
H
A
Low Cut Filter
A
OFF
H
A
Low Cut Filter
A
Low
3.4 Short press button to confirm
3.2 Long press button to enter ‘ Low Cut Filter ’ setting page
3.3 Press button to select LCF ‘ Low/High/OFF ’
3.1 Press button to ‘ Low Cut Filter ’ display page
3. Low Cut Filter ‘ Low/High/OFF ’ Adjustment
Low-cut function will filter out the low-frequency part of the audio source,
such as the chirping and crowd noise, and the main audio source will
be more crisp. Low cut divided into low cut in low range and low cut in
high range, low range is to filter out part of the noise, while high range
of low cut filter out all noise. Turn off the low cut to restore the true, the
main source will be more vigorous, but it can be adjusted according
to actual needs.
18