Commell HE-772 User manual

HE-772
Half-size PCI Bus CPU Card
User’s Manual
Edition A
2010/10/05

HE-772 User’s Manual
-1-
Copyright
Copyright 2010. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to
make improvements to the products.
This document contains proprietary information and protected by copyright. No part of
this document may be reproduced, copied, or translated in any form or any means
without prior written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of
their respective owners. Disclaimer
The company shall not be liable for any incidental or consequential damages resulting
from the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including
without limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications
of the product described within it at any time without notice and without obligation to
notify any person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT

HE-772 User’s Manual
-2-
Packing List:
Please check the package content before you starting using the board.
Hardware:
HE-772 “Half-size PCI Bus CPU Card” x 1
Cable Kit:
USB Cable x 1
(
OALUSB
A
-3
)
Audio Cable x 1
(OALPJ-HDU)
Dual COM PORT cable x 1
(OALES-BKU2)
Printed Matters:
Driver CD x 1 (Including User’s Manual)

HE-772 User’s Manual
-3-
Index
Chapter 1 <Introduction>.................................................................................5
1.1 <Product Overview>..................................................................................5
1.2 <Product Specification>.............................................................................6
1.3 <Mechanical Drawing>..............................................................................8
1.4 <Block Diagram>.......................................................................................9
Chapter 2 <Hardware Setup>.........................................................................10
2.1 <Connector Location>.............................................................................10
2.2 <Jumper Reference>...............................................................................12
2.3 <Connector Reference>..........................................................................13
2.3.1 <Internal Connector>..............................................................13
2.3.2 <External Connector> ............................................................13
2.4 <CPU and Memory Setup>.....................................................................14
2.5 <CMOS & ATX Setup>............................................................................15
2.6 < Enhanced IDE & CF Interface >...........................................................16
2.7 <Serial ATA Interface>............................................................................17
2.8 <LAN Interface> ......................................................................................18
2.9 <Onboard Display Interface> ..................................................................19
2.9.1 <Analog VGA Interface> ........................................................19
2.9.2 <Digital Display>.....................................................................20
2.10 <Onboard Audio Interface>...................................................................24
2.11 <USB2.0 Interface>...............................................................................25
2.12 <GPIO and SMBUS Interface> .............................................................26
2.13 <Serial Port Jumper Setting >...............................................................27
2.14 <Power & FAN Connector >..................................................................30
2.14.1 <Power Input>......................................................................30
2.14.2 <Power Input>......................................................................31
2.14.3 <Fan Connector> .................................................................32
2.15 <Indicator and Switch>..........................................................................33
Chapter 3 <System Configuration>...............................................................34

HE-772 User’s Manual
-4-
3.1 <Audio Configuration>.............................................................................34
3.2 <Video Memory Setup>...........................................................................35
3.3 <Display Properties Setting>...................................................................37
Chapter 4 <BIOS Setup> ................................................................................40
Appendix A <I/O Port Pin Assignment> .......................................................41
A.1 < LPT Port >............................................................................................41
A.2 < CRT Port > ...........................................................................................41
A.3 < LAN Port >............................................................................................42
A.4 < IrDA Port >............................................................................................42
A.5 < SMBUS Port >......................................................................................42
A.6 < DIO Port >............................................................................................43
A.7 < IDE Port >.............................................................................................43
A.8 < Serial ATA Port >..................................................................................44
A.9 < PS2 Port >............................................................................................44
A.10 < ATKB Port >........................................................................................44
Appendix B <Flash BIOS>..............................................................................45
B.1 BIOS Auto Flash Tool..............................................................................45
B.2 Flash Method...........................................................................................45
Appendix C <System Resources> ................................................................46
C.1 <Direct memory access(DMA)> (HE-772A)............................................46
C.2<Input/output(IO)> (HE-772A)..................................................................46
C.3<Interrupt reguest(IRQ)> (HE-772A)........................................................47
C.4<Memory> (HE-772A)..............................................................................48
Appendix E <Watch Dog timer Setting >......................................................50
Contact Information........................................................................................51

HE-772 User’s Manual
-5-
Chapter 1 <Introduction>
1.1 <Product Overview>
HE-772G/H/A is the Half-size PCI Bus CPU Card, with Intel® Atom N450/D410/D510
processor, integrated GMA3150 graphics, Intel® ICH8M, DDR2 SO-DIMM memory,
Realtek HD Audio , CF , SATAII , LVDS , LPT , IrDA, DIO, CN_USB , PS2 , SMBUS,
CN_INV , CN_CRT , IDE , CN_ATKB , MINI-CARD and Intel® 82583V Gigabit LAN.
Intel® Atom Processor
The Intel® Atom N450/D410/ D510 processor supports one channel of 667 MHz DDR2
SDRAM up to 2GB/4GB/4GB. The chipset features power-efficient graphics with an
integrated 18-bit 3D graphics engine based on Intel® Graphics MediaAccelerator 3150
architecture with LVDS, CRT display ports. The DMI is designed into the Pineview-M(D)
processor to provide an efficient high-bandwidth communication channel between the
processor and the ICH8M.
Embedded Intel® ICH8M
The board integrates Intel® ICH8M. It provides I/O capabilities and flexibility via
high-bandwidth interfaces such as PCIE and Hi-Speed USB 2.0 connectivity. Serial
ATA . HD Audio , Mini-card , CF , LAN , HD Audio . IDE , CN_USB
Flexible Extension Interface
The board also provides Compact Flash Type II socket and 2 x Mini-card socket.

HE-772 User’s Manual
-6-
1.2 <Product Specification>
General Specification
Form Factor Half-size PCI Bus CPU Card
CPU Intel® Atom N450 Processor 1.66GHz (HE-772G)
Intel® Atom D410 Processor 1.66GHz (HE-772H)
Intel® Atom D510 Processor 1.66GHz (HE-772A)
Package type: FCBGA559
Memory 1 x 200-pin DDR2 SO-DIMM 667MHz SDRAM up to 2GB/4GB/4GB
(HE-772G / HE-772H / HE-772A)
Unbufferred, none-ECC memory supported only
Chipset Intel® ICH8M
BIOS Phoenix-Award v6.00PG 8Mb SPI flash BIOS
Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 2.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255 sec./min.
of timeout value
Real Time Clock Intel® ICH8-M built-in RTC with lithium battery
Enhanced IDE IDE supports 44-Pin Disk On Module with +5V power supply
One CompactFlash Type II socket on solder side
Serial ATAII Intel® ICH8M integrates 3 Serial ATAII interfaces
(No RAID Function)
Up to 300MB/s of transfer rate
Multi-I/O Port
Chipset Intel® ICH8M with Winbond® W83627DHG-P controller
Serial Port Five RS-232 and one RS232/422/485 serial ports
USB Port Eight Hi-Speed USB 2.0 ports with 480Mbps of transfer rate
IrDA Port One IrDA compliant Infrared interface supports SIR
K/B & Mouse External PS/2 keyboard and mouse ports on rear I/O panel
GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O I
nterface
Smart Fan One CPU fan connectors for fan speed controllable
Audio Port Realtek ALC888 HD Codec
VGA Display Interface
Chipset Intel® Atom N450 processor (System Controller Hub) (HE-772G)
Intel® Atom D410 processor (System Controller Hub) (HE-772H)
Intel® Atom D510 processor (System Controller Hub) (HE-772A)
Frame Buffer Up to 384MB shared with system memory
Display Type CRT, LVDS monitor with analog display
Connector External DB15 female connector on rear I/O panel
Onboard 20-Pin LVDS and 5-Pin inverter connector

HE-772 User’s Manual
-7-
Ethernet Interface
Controller 2 x Intel® 82583V Gigabit Ethernet controller
Type Triple speed 10/100/1000Base-T
Auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector Two External RJ45 connectors with LED on rear I/O panel
Expansive Interface
PCIE mini card Two PCIE mini card socket
Power supply: +1.5V, 3VSB
Power and Environment
Power
Requirement DC 5V/12V power required, optional 5VSB for ATX
Onboard 4-pin power connector & 3-pin ATX connector
Dimension 185 (L) x 122 (H) mm
Temperature Operating within 0 ~ 60O
p
C (32 ~ 140O
p
F)
Storage within –20 ~ 85O
p
C (-4 ~ 185O
p
F)
Ordering Code
HE-772G
Support Intel® Atom N450 processor with onboard VGA, LVDS for 18-bits, Audio, Giga LAN, USB2.0, SATAII, PCIE mini card, PCI,
Mini-PCI, Serial Port, CF, SMBUS, GPIO, IrDA, LPT, CDIN, SPDIF
HE-772H
Support Intel® Atom D410 processor with onboard VGA, LVDS for 18-bits, Audio, Giga LAN, USB2.0, SATAII, PCIE mini card, PCI,
Mini-PCI, Serial Port, CF, SMBUS, GPIO, IrDA, LPT, CDIN, SPDIF
HE-772A Support Intel® Atom D510 processor with onboard VGA, LVDS for
18-bits, Audio, Giga LAN, USB2.0, SATAII, PCIE mini card, PCI,
Mini-PCI, Serial Port, CF, SMBUS, GPIO, IrDA, LPT, CDIN, SPDIF
CBP-5P4 Support 4 X PCI slots backplane
MPX-954E PCI Express mini card support 2 x RS232 , 2 x RS422/RS485.
The specifications may be different as the actual production.
For further product information please visit the website at TUhttp://www.commell.com.twUT

HE-772 User’s Manual
-8-
1.3 <Mechanical Drawing>
Unit: inch

HE-772 User’s Manual
-9-
1.4 <Block Diagram>
RS232/422/485
LPT , IrDA , Dio ,
SYSFAN , CPUFAN
2 x PCIE mini card
CRT DDR2 SODIMM 667 MHz up
Intel® Atom
to 2G/4G/4G
18bit Single Channel LVDS
ICH8M
W83627DHG-P
N450/D410/
D510
VGA Interface
Intel GMA 3150
1 x IDE
ICHF81216D
COM 1/2/3/4/5/6
6 x USB2.0 1 x Compact Flash
ALC888 HD Audio
2 x Giga LAN
3 x Serial ATA II

HE-772 User’s Manual
-10-
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
CN_ATKB
CN_LVDS
MINICARD CN_USB DDRII
CN_DIO
CN_PS JFRNT
SYSFAN
CN_SMBUS
SATA
CN_LPT COM1/2 DC_IN
IDE
CPUFAN
CN_INVCN_IRCFCN_AUDIO
COM3/4/5/6
CN_CRT

HE-772 User’s Manual
-11-
RJ45 1/2 PS2
HE-772G/H/A
CRT

HE-772 User’s Manual
-12-
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JVLCD Panel Voltage Setting
JAT Power mode select
JCSEL1
JCSEL2 CN_COM2 RS-232 RS422 RS485 Setting / CN_IR IrDA Setting
JP1
JP2 CN_COM3/4/5/6 RS-232
JCSEL1
JRTC
JVLCD
JAT
JP1/2
JCSEL2

HE-772 User’s Manual
-13-
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
DDRII 200 –pin DDR2 SO-DIMM SDRAM
slot
SATA1/2/3 7-pin Serial ATA connector
CF Compact Flash Type II socket
IDE 44-pin primary IDE connector
MINI_CARD 2 x 52-pin PCI Express mini card
CN_LVDS 10 x 2-pin LVDS connector
CN_INV 5-pin LCD inverter connector
CN_USB1/2/3 5 x 2-pin USB connector
CN_AUDIO 5 x 2-pin audio connector
CN_COM1/2/3/4/5/6 10 x 2-pin com connector
JFRNT 10-pin switch/indicator connector
SYSFAN 3-pin system cooler fan connector
CPUFAN 4-pin CPU cooler fan connector
DC_IN DC 5V/12V input connector
CN_LPT 13 x 2-pin printer connector
CN_DIO 6 x 2-pin digital I/O connector
CN_IR 5-pin IrDA connector
JCSEL1
JCSEL2 CN_COM2 RS-232 RS422 RS485 Setting / CN_IR IrDA Setting
JRTC CMOS Operating/Clear Setting
CN_CRT 5 x 2-pin CRT connector
CN_SMBUS 5-pin SMBUS connector
JAT Power mode select
JRTC CMOS Operating/Clear Setting
2.3.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector
PS2 PS2 keyboard and mouse connector
RJ45 RJ45 LAN connector

HE-772 User’s Manual
-14-
2.4 <CPU and Memory Setup>
Non-ECC, unbuffered memory is supported only.
HE-772G provides one 200-pin DDR2 SO-DIMM to support DDR2 667 memory
modules support up to 2GB of capacity.
Suggestion:
DDR2 SO-DIMM Modules:
–Raw Card A = 2 Ranks of x16 SDRAMs (Double-sided)
–Raw Card C = 1 Rank of x16 SDRAMs (Single-sided)
HE-772H/ A provides one 200-pin DDR2 SO-DIMM to support DDR2 667 memory
modules support up to 4GB of capacity.
Suggestion:
DDR2 SO-DIMM Modules:
–Raw Card C = 1 Rank of x16 SDRAMs (Single -sided)
–Raw Card D = 1 Rank of x8 SDRAMs (Single-sided)
–Raw Card E = 2 Ranks of x8 SDRAMs (Double -sided)
DDRII

HE-772 User’s Manual
-15-
2.5 <CMOS & ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting
Jumper: JAT
Type: onboard 3-pin jumper
JAT Mode
1-2 AT Mode
2-3 ATX Mode
Default setting
JRTC JAT

HE-772 User’s Manual
-16-
2.6 < Enhanced IDE & CF Interface >
The board supports one enhanced IDE interface for 2 ATAPI devices with ATA33. Based
on embedded application, the board has one 44-pin IDE connector +5V supported for
disk on module.
The board also provides a Compact Flash Type II socket.
CF IDE

HE-772 User’s Manual
-17-
2.7 <Serial ATA Interface>
Based on Intel ICH8M, the board provides one Serial ATAII interfaces with up to
300MB/s of transfer rate.
SATA 1/2/3

HE-772 User’s Manual
-18-
2.8 <LAN Interface>
The Intel® 82583v supports triple speed of 10/100/1000Base-T, with IEEE802.3
compliance.
LAN
`