CommScope NG4access ODF Platform Value-Added Module User manual

© 2017 CommScope. All Rights Reserved.
Installation Instructions
25285-A
300001749219 Rev B
TECP-90-702, Issue 4, April 2017
NG4access®Frame (Concrete Floor)

TECP-90-702 • Issue 4 • April 2017 • Preface
Page ii
COPYRIGHT
© 2017, CommScope, Inc.
All Rights Reserved.
REVISION HISTORY
TRADEMARK INFORMATION
CommScope, CommScope (logo), and NG4access are trademarks of CommScope Inc.
DISCLAIMER OF LIABILITY
Contents herein are current as of the date of publication. CommScope reserves the right to change the contents without prior notice.
In no event shall CommScope Inc. be liable for any damages resulting from loss of data, loss of use, or loss of profits and
CommScope Inc. further disclaims any and all liability for indirect, incidental, special, consequential or other similar
damages. This disclaimer of liability applies to all products, publications and services during and after the warranty period.
This publication may be verified at any time on the CommScope website using the following URL:
http://www.commscope.com/SupportCenter
ISSUE DATE REASON FOR CHANGE
1 4/2013 Original.
4 April 2017 Reformatted to CommScope format.

TECP-90-702 • Issue 4 • April 2017 • Preface
Page 1
© 2017, CommScope, Inc.
TABLE OF CONTENTS
Content Page
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Admonishments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
List of Acronyms and Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1 TOOLS AND MATERIALS REQUIRED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 FOOTPRINT OF FRAME AND FIBER OPTIC STORAGE PANEL (FOTSP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 MOUNTING THE FRAME ON A CONCRETE SURFACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 INSTALLING A FIBER OPTIC STORAGE PANEL (FOTSP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5 GROUNDING THE FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6 SECURING TWO FRAMES TOGETHER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7 CUSTOMER INFORMATION AND ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

TECP-90-702 • Issue 4 • April 2017 • Preface
Page 2
© 2017, ADC Telecommunications, Inc.
TABLE OF CONTENTS
Content Page
Blank

TECP-90-702 • Issue 4 • April 2017 • Preface
Page 3
© 2017, CommScope, Inc.
ABOUT THIS MANUAL
This manual provides complete instructions for installing a NG4access frame on a concrete
floor, grounding the frame, and securing two frames.
RELATED PUBLICATIONS
Listed below are related manuals and their publication numbers. Copies of these publications can
be ordered using the following URL:
http://www.commscope.com/SupportCenter
NG4access ODF Platform Application and Planning Manual 90-701
Contains an NG4access overview and information for planning a NG4access
application.
NG4access Frame Installation Manual: Raised Floor 90-708
Provides pictorial instructions for installing an NG4access frame on a raised
floor and grounding the frame.
NG4access ODF Platform Universal Chassis Installation Manual 90-703
Provides installation instructions for the NG4access standard chassis.
NG4access ODF Platform Splice Chassis and Splice Tray
Installation Manual 90-704
Provides installation instructions for the NG4access standard chassis.
NG4access ODF Platform Patch Cord Routing Guide 90-705
Provides pictorial guidelines for routing patch cords on a lineup consisting of
one or more NG4access frames. This manual consists of laminated cards that
hang on the front of the lineup.
NG4access ODF Platform Rear Side Routing Guide 90-706
Provides pictorial guidelines for routing cables and installing adapter packs and
cabled modules on the rear side of a lineup consisting of one or more NG4ac-
cess frames. This manual consists of laminated cards that hang on the rear of
the lineup.
Title/Description Publication Number

TECP-90-702 • Issue 4 • April 2017 • Preface
Page 4
© 2017, CommScope, Inc.
ADMONISHMENTS
Important safety admonishments are used throughout this manual to warn of possible hazards to
persons or equipment. An admonishment identifies a possible hazard and then explains what
may happen if the hazard is not avoided. The admonishments — in the form of Dangers,
Warnings, and Cautions — must be followed at all times. These warnings are flagged by use of
the triangular alert icon (seen below), and are listed in descending order of severity of injury or
damage and likelihood of occurrence.
GENERAL SAFETY PRECAUTIONS
LIST OF ACRONYMS AND ABBREVIATIONS
The following acronyms are used in this manual:
FOT Fiber Optic Terminal
IFC Intra Facility Cable
OSP Outside Plant
Danger: Danger is used to indicate the presence of a hazard that will cause severe personal
injury, death, or substantial property damage if the hazard is not avoided.
Warning: Warning is used to indicate the presence of a hazard that can cause severe personal
injury, death, or substantial property damage if the hazard is not avoided.
Caution: Caution is used to indicate the presence of a hazard that will or can cause minor
personal injury or property damage if the hazard is not avoided.
Danger: Infrared radiation is invisible and can seriously damage the retina of the eye. Do not
look into the ends of any optical fiber. Do not look directly into the optical adapters of the
adapter packs. Exposure to invisible laser radiation may result. An optical power meter should
be used to verify active fibers. A protective cap or hood MUST be immediately placed over any
radiating adapter or optical fiber connector to avoid the potential of dangerous amounts of
radiation exposure. This practice also prevents dirt particles from entering the adapter or
connector.

TECP-90-702 • Issue 4 • April 2017
Page 1
© 2017, ADC Telecommunications, Inc.
1 TOOLS AND MATERIALS REQUIRED
The tools and materials required for mounting the NG4access frame on a concrete surface are
specified in Table 1, Table 2, and Table 3.
Table 1. Tools Required
TOOL PICTURE
Adjustable wrenches (2)
0.25 to 1 inch (8 to 25.4 mm)
Crow bar
Drill with metal and concrete drill bits
0.25 to 1 inch (8 to 25.4 mm)
Ruler or tape measure
Torque wrench
19.9 ft.-lbs. (27 Nm)
Allen wrench (5/16-inch)
Note: Used for leveling frame
Hammer
Set of combination open-end/box-end
wrenches
0.25 to 1 inch (8 to 25.4 mm)
12494-B
12495-B
12496-B
cm
131
12825-a
17721-A
18406-A
12500-B
12506-B

TECP-90-702 • Issue 4 • April 2017
Page 2
© 2017, ADC Telecommunications, Inc.
Set of sockets
0.25 to 1 inch (8 to 25.4 mm)
Crimping tool
0.25 to 0.3 inches (6.35 to 7.62 mm)
Note: Used for grounding frame
Vacuum
Flat tip (–) and Phillips (+) screwdrivers
(#1, #2, and #3)
Table 2. Ground Wire Kit Components (Accessory)
ITEM DESCRIPTION/PICTURE
Ground cable (13 ft.) #6 AWG (4.1 mm) solid copper wire
Nylon cable clamps (8)
12-24 x 0.5 inch screws
2-hole copper compression lug (1) with
0.75-inch hole spacing.
Note: Accommodates #6 AWG wire
Table 1. Tools Required, continued
TOOL PICTURE
12504-B
12824-A
12505-B
12503-B
18413-A
18414-A
12498-B

TECP-90-702 • Issue 4 • April 2017
Page 3
© 2017, ADC Telecommunications, Inc.
Table 3. Other Components Used
PART PICTURE
Concrete floor installation kit
(four threaded assemblies)
Hold-down washer (4)
(provided with frame)
STUD
TORQUE LIMITING HEX NUT
METAL SLEEVE
NYLON SPACER
EXPANDABLE CONE
FLAT WASHER
TOP FLANGE
(SHEARS OFF)
PLASTIC COVER
NOTE: ONE PIECE
TORQUE NUT
18008-B
21899-A

TECP-90-702 • Issue 4 • April 2017
Page 4
© 2017, ADC Telecommunications, Inc.
2 FOOTPRINT OF FRAME AND FIBER OPTIC STORAGE PANEL (FOTSP)
Figure 1 shows the frame footprint. Figure 2 shows the FOTSP footprint. The optional FOTSP
is installed adjacent to the frame on the left front side.
Figure 1. Frame Footprint (Optional Template Shown)
Figure 2. FOTSP Footprint
25162-A
23.89 IN.
(60.68 CM)
29.84 IN. (75.79 CM)
1.0 IN. (2.54 CM) DIAMETER
(4) PLACES
8-5/16 IN.
(21.11 CM)
7-13/16 IN.
(19.84 CM)
13IN.
(33.02 CM)
25-1/2 IN. (64.77 CM)
FRONT
22-27/32 IN. (58.02 CM)
2-7/8 IN.
(7.30 CM)
9-5/8 IN.
(23.45 CM)
11.88 IN. (30.17 CM)
18.98 IN.
(48.21 CM)
FRONT
2.5 IN.
(6.35 CM)
25243-A
23.98 IN.
(60.91 CM)
RADIUS1.0 IN.
(2.54 CM)
10.90 IN.
(27.69 CM)
3.75 IN. (9.52 CM)
SLOT 1.75 X 1.0 IN.
(4.44 X 2.54 CM)
6.88 IN. (17.47 CM)
4.0 IN. (10.16 CM)