CONDTROL Auto RotoLaser User manual

CONDTROL Auto RotoLaser
EN CONTENTS
SAFETY INSTRUCTIONS 4
INTENDED USE 5
SET 5
TECHNICAL SPECIFICATIONS 6
PRODUCT DESCRIPTION 7
OPERATION 10
OPERATION MODES 12
ACCURACY CHECK 16
CARE AND MAINTENANCE 19
UTILIZATION 20
WARRANTY 20
DE INHALT
SICHERHEITSVORSCHRIFTEN 22
PRODUKTBESCHREIBUNG 23
LIEFERUMFANG 23
TECHNISCHE SPEZIFIKATIONEN 24
GERÄTEÜBERSICHT 25
BETRIEB 28
BETRIEBSMODUS 30
GENAUIGKEITSÜBERPRÜFUNG 34
PFLEGE UND BEDIENUNG 37
ENTSORGUNG 38
GARANTIE 39
WARTUNG UND REPARATUR 40

CONDTROL Auto RotoLaser
RU
                         

 








 
PL


 
CHARAKTERYSTYKA TECHNICZNA 61


TRYBY PRACY 67

KONSERWACJA I EKSPLOATACJA 74
UTYLIZ AC JA 76
GWARANCJA 77

RotaRy l aseR
4
user manual
EN
CONDTROL Auto RotoLaser
SAFETY INSTRUCTIONS
Attention! This user manual is an essential part of this product.
The user manual should be read carefully before you use the product
for the first time. If the product is given to someone for temporary
use, be sure to enclose user manual to it.
- Do not misuse the product
- Do not remove warning signs and protect them from abrasion,
because they contain information about safe operation of the
product.
Laser radiation!
Do not stare into beam
Class 2 laser
<1 mW 635 nm
EN60825-1: 2007-03
-Do not look into the laser beam or its reflection, with unprotected
eye or through an optical instrument. Do not point the laser beam at
people or animals without the need. You can dazzle them.
-To protect your eyes close them or look aside.
- Always install the product in such a way, so that laser line is below
or above eye level.
- Do not let unauthorized people enter the zone of product operation.
- Store the product beyond reach of children and unauthorized
people.
- It is prohibited to disassemble or repair the product yourself. Entrust
product repair to qualified personnel and use original spare parts
only.
- Do not use the product in explosive environment, close to flammable
materials.

RotaRy l aseR
5
user manual
EN
CONDTROL Auto RotoLaser
INTENDED USE
CONDTROL Auto RotoLaser – self-levelling rotary laser level, designed
for construction workers, plasterers, and contractors intended to
build vertical and horizontal planes, plumb line (zenith). The product
has scan function that allows building only a part of laser plane
defined by user.
The product is suitable for use at both indoor and outdoor building
areas
SET
Rotary laser – 1 pc.
Universal mount on wall/tripod 5/8’’ – 1 pc.
Batteries – 4 pcs.
Battery charger – 1 pc.
Laser receiver – 1 pc.
Mount for laser receiver – 1 pc.
Remote control – 1 pc.
Laser intensive glasses – 1 pc.
Magnetic target board – 1 pc.
User manual – 1 pc.
Plastic case – 1 pc.
- Laser intensive glasses are used for better recognition of the laser
beam, do not use them for other purposes. Laser glasses do not
protect from laser radiation as well as ultraviolet radiation and reduce
color perception.

RotaRy l aseR
6
user manual
EN
CONDTROL Auto RotoLaser
TECHNICAL SPECIFICATIONS
Working range with receiver 400 m (in diameter)
Accuracy 30” (±0,15 mm/1 m)
Self-levelling range ±5°
Laser type Class II 635 nm < 1 mW
Rotation speed 0; 120; 300; 600 rpm
Scan function 
Remote control operating
distance 20 m
Operation temperature -100C ~ +500C
Power supply of rotary laser Rechargeable
DC4.8-6 V (4 x 2600mAh AA Ni-MH)
Power supply of remote control 
Power supply of laser receiver 
Continuous working time up to 20 h
Waterproof and dustproof IP 54
Tripod mount 5/8"
Dimensions 150 X 128 X 161 mm
Weight 1,4 kg (with batteries)

RotaRy l aseR
7
user manual
EN
CONDTROL Auto RotoLaser
PRODUCT DESCRIPTION
1. Laser output window
2. Rotary head
3. Aperture for plumb line
4. Control panel
5. Battery cover
6. Battery charger jack
7. Fixator of battery cover
8. Tripod thread 5/8”
9. Location for universal mount fixing
2
1
1
2
8
4
6
7
9
3
5
6

RotaRy l aseR
8
user manual
EN
CONDTROL Auto RotoLaser
Control panel
1. Turn on/off
2. Power indicator
3. Manual mode
4. Manual mode indicator
5. Tilt mode
6. Tilt mode indicator
7. Remote control sensor
5
1 2
6
3
4
7

RotaRy l aseR
9
user manual
EN
CONDTROL Auto RotoLaser
Remote control
3
6
2
4
5
1
1. Remote control signal indicator
2. Scan mode/scan sector
3. Move laser dot/scan sector clockwise
4. Move laser dot / scan sector counterclockwise
5. Change rotation speed/stop rotation
6. Manual mode
Use remote control to manage the product at distance up to 20 m.
When sending signals to the product indicator on remote control
flashes red.

RotaRy l aseR
10
user manual
EN
CONDTROL Auto RotoLaser
Laser receiver
Laser receiver allows using the product outdoor as well as while
intensive sunshine at distance up to 400 m (in diameter) when it’s
difficult to recognize laser beam.
1 2 3
4
5
OPERATION
Battery charging
In case power indicator starts flashing while operation – batteries
need to be charged. Please use battery charger included in the set.
Full charging takes approximately 5 hours. While charging red light
indicator on battery charger will be on. As soon as indicator becomes
1. Turn on/off
2. Turn on/off sound signal
3. High/normal accuracy mode
4. Display
5. Receiver sensor

RotaRy l aseR
11
user manual
EN
CONDTROL Auto RotoLaser
green, batteries are fully charged, battery charger can be unplugged.
Take batteries out of the product if it is not used for a long time. All
batteries should be of the same type and brand with the same charge
level. Do not leave discharged batteries in the product.
Replace batteries in laser receiver
Battery compartment is located on the back side of laser receiver.
Remove battery cover, take out discharged batteries and install new
ones, observing correct polarity. Put battery cover back.
Use alkaline AAA batteries only. Remove the batteries from laser
receiver if it is not used for a long period of time to avoid corrosion and
battery discharging. All batteries should be replaced simultaneously.
All batteries should be of the same type and brand with the same
charge level.
Replace batteries in remote control
Battery compartment is located on the back side of remote control.
Remove the battery cover: slide out the battery cover and remove it.
Insert the batteries, observing correct polarity. Slide the cover back
until a click is heard.
Use alkaline AAA batteries only. Remove the batteries from remote
control if it is not used for a long period of time to avoid corrosion and
battery discharging. All batteries should be replaced simultaneously.
All batteries should be of the same type and brand with the same
charge level.

RotaRy l aseR
12
user manual
EN
CONDTROL Auto RotoLaser
Turn on/off the product
Press button , to turn on/off the product. When the product is
on, power indicator is on as well. After turn off the product power
indicator will go out.
OPERATION MODES
Automatic mode (build horizontal/vertical plane)
Place the product on a flat surface, tripod 5/8” or universal mount in
horizontal or vertical position.
Turn on the product. Power indicator turns on as well.
Laser beam is blinking while self-levelling. As soon as self-levelling is
finished rotary head starts rotating clockwise at 600 rpm. Turn off the
product.
Manual operating mode indicator starts to blink when the instrument
is out of the range of automatic compensation (5°). Laser beam will
blink, rotary head will not rotate. Turn off the product and turn it on
again.
Press button to switch to tilt mode. Tilt mode indicator will flash
red. If the product is unbalanced by some external influence, it will
not perform self-levelling again. Turn off the product, then turn it on
and repeat operation.

RotaRy l aseR
13
user manual
EN
CONDTROL Auto RotoLaser
Manual mode
This mode allows construction of laser planes at any angle inclination.
Place the product on a solid and flat surface. Turn on the product.
Power indicator turns on.
Laser beam is blinking while self-levelling. As soon as self-levelling
is finished rotary head starts rotating clockwise at 600 rpm. Press
button on the product or button on remote control. Manual
mode is activated, manual mode indicator becomes red. Install the
product at required angle and fix its position.
To exit from manual mode and return to automatic mode press
button on the product or on remote control. Manual mode
indicator will turn off.
Top plumb dot
The product allows working with top plumb dot. It is on in any
operation mode of the product.
Rotation speed
Use remote control to run this function.
Speed 600 rpm is default. Press button to switch between
speeds of rotary head. Rotation speeds change in the following way:
600-0-120-300-600 rpm.
Attention! The slower rotation speed, the brighter laser beam.

RotaRy l aseR
14
user manual
EN
CONDTROL Auto RotoLaser
Scan mode
Scan mode allows seeing laser line at long distance. Use remote
control to run this function.
Press button to activate scan mode.
By series press on button choose required scan sector –
0°, 10°; 45°; 90°; 180°. Press button to move scan sector
counterclockwise, button - clockwise.
To exit scan mode press . Rotary head will start rotating.
Work with laser receiver
Use universal mount included in the set to fix laser receiver on
telescopic levelling rod. Magnets on top and lateral sides of laser
receiver allow fixing it on metal surfaces.

RotaRy l aseR
15
user manual
EN
CONDTROL Auto RotoLaser
1. Press button to turn on laser receiver.
2. Press button to turn on/off sound signal. By default sound
signal is enabled – symbol appears on the display.
3. Press button to select required mode –
1) high accuracy ±1.5mm/40m. Symbol appears on the display
2) normal accuracy ±2.5mm/40m. Symbol appears on the display.
Expand sensor of laser receiver towards the laser beam and move
laser receiver down/up arrows on the display. For convenience, you
can use the screen on the back of the detector. Down arrow on the
display indicates that laser receiver should be lowered. The up arrow
on the display indicates that laser receiver needs to be lifted up. When
the marks on the sides of laser receiver are at the same level with the
laser line, symbol appears on the display and you hear
sound signal (if sound signal is enabled) – laser receiver is at the same
level with the laser line.

RotaRy l aseR
16
user manual
EN
CONDTROL Auto RotoLaser
Magnetic target board
Magnetic target board helps to
make the layout of ceiling systems or
framework structures. Built-in magnet
enables attaching a target to the ceiling
rails or on the frame profile. The target
has a linear layout on its surface, which
allows determining deviation from the
nominal level and making check points
while marking by laser leveling.
ACCURACY CHECK
Axis X
1. Place the product at 0.5 m distance from one wall and 10 m
distance from another wall, so that axis X is aimed at the wall.
2. Turn on the product. As soon as self-levelling is finished, mark
location of laser line on both walls by points X1 and X2.
3. Turn off the product. Move it to the opposite wall, position of the
product should remain unchanged.
4. Turn on the product. Align laser line with the previously made
point X2. Mark point X3 on the opposite wall.

the product and contact service center.

RotaRy l aseR
17
user manual
EN
CONDTROL Auto RotoLaser
Axis Y
1. Place the product at 0.5 m distance from one wall and 10 m
distance from another wall, so that axis Y is aimed at the wall.
2. Turn on the product. As soon as self-levelling is finished, mark
location of laser line on both walls by points Y1 and Y2.

RotaRy l aseR
18
user manual
EN
CONDTROL Auto RotoLaser
3. Turn off the product. Move it to the opposite wall, position of the
product should remain unchanged.
4. Turn on the product. Align laser line with the previously made point
Y2. Mark point Y3 on the opposite wall.

product and contact service center.

RotaRy l aseR
19
user manual
EN
CONDTROL Auto RotoLaser
CARE AND MAINTENANCE
Rotary laser is a high-precision instrument and requires careful
handling. Before using as well as after physical impact (falling, hitting)
carry out accuracy check.
Observation of the following recommendations will extend the life of
the device:
1) Store the product, spare parts and its accessories beyond reach of
children and unauthorized people.
2) The instrument should be transported in the off state inside the
case only.
3) Do not store the product in dusty or dirty locations. The product is
dust and dirt resistant, but long-time exposure to these elements may
damage internal moving parts of the product.
4) Store the product in dry locations. The product is water resistant,
but precipitate, humidity and liquids containing minerals may damage
the electrical circuits of the product. Do not try to dry the unit by fire
or a hairdryer.
5) Do not store the product in locations where temperature is more

damage batteries, deform or melt some plastic parts.
6) Do not store the product in locations where temperature is less

After storage in low temperature conditions and subsequent transfer
to a warm room, the device is heated, causing moisture condense
inside the instrument and damage the chip.
7) Protect the instrument from bumps, drops, strong vibrations. This
can lead to loss of accuracy.
8) Carry out accuracy check regularly (see paragraph «Accuracy
check»).
9) To clean the product use a soft wet cloth. Do not use harsh
chemicals, cleaning solvents or detergents.
          
isopropyl alcohol.

RotaRy l aseR
20
user manual
EN
CONDTROL Auto RotoLaser
11) Remove batteries from the product if it not used for a long time.
12) Do not leave discharged batteries in the product.
13) Avoid heating the batteries to avoid the risk of explosion and
electrolyte leakage. In case of liquid contact with skin, wash it
immediately with soap and water. In case of contact with eyes, flush
with clean water during 10 minutes and consult the doctor.
UTILIZATION
Expired tools, accessories and package should be passed for waste
recycle. Please send the product to the following address for proper
recycle:
Condtrol GmbH
Wasserburger Strasse 9
84427 Sankt Wolfgang
Germany
Do not throw the product in municipal waste!

and their components must be collected separately and submitted to
environmentally friendly recycle of wastes.
WARRANTY
All Condtrol GmbH products go through post-production control and
are governed by the following warranty terms. The buyer’s right to
claim about defects and general provisions of the current legislation
do not expire.
1) Condtrol GmbH agrees to eliminate all defects in the product,
discovered during the warranty period, that represent the defect in
material or workmanship in full volume and at its own expense.
2) The warranty period is 24 months and starts from the date of
purchase by the end consumer (see the original supporting document).