Connection Centro User manual

www.connection.uk.com
Centro
Assembly Instructions

Assembly Instructions
Preparation - Components
Remove all packaging from each component and lay them on the floor.
A Long oak fascia
B Short oak fascia
C Steel support frame with underside cover attached
D Table tops*
E Power module covers**
F Legs
G Power module housing (and any specified power modules)**
*Tables shorter than 2.6 metres will have one table top.
**These components are included alongside tables with optional power modules or cutouts only.
E
C
F
AB
G

Assembly Instructions
Preparation - Fixing Kit
Your table will be supplied with a fixing kit in a sealed red bag attached to one long oak facia. Empty its
contents onto a suitable surface.
A Long furniture bolts
B Short furniture bolts
C Washers
D Allen head bolts (not to be confused with larger allen head bolts pre-installed in legs)
E Double ended pins*
F Cam covers*
G Biscuits*
*These fixings are included alongside tables with split table tops only.
D
E
C
F
A
B
G

Assembly Instructions
Centro Assembly
Cable managed
leg and cutout
We advise that assembly of a Centro table requires 2 people.
1 Remove the pre-installed allen head bolts and washers from one leg and keep these separate from any
other fixings. Also detatch the underside cover from the steel support frame (item C) to begin assembly
2 Lift the steel support frame from one end, leaving the other end on the floor
3 Using the allen head bolts and washers removed in step 1, use these to tightly fix the first leg in place
Please Note: If your Centro table has been specified with optional
power modules or cutouts, first ensure the cable managed leg is
installed at the corner of the table closest to the power outlet or
floor box.
4 Repeat steps 1 to 3 for the remaining three legs
1 2 3
4
4a

Assembly Instructions
Centro Assembly
5
6
5 Using the button head bolts, loosely attach the short oak fascias
6 Again, using the button head bolts loosely attach the long oak fascias on both sides
7 Place a table top onto the structure
For tables under 2.6 metres - with a single table top, jump to step 11
7

Assembly Instructions
Centro Assembly
x4
8 Insert 3 biscuits into the slots as shown
9 Insert 4 double ended pins into the table top that is sat on the structure
For tables 2.6m and over with 2 part table tops:
10 Place the second part of the table top onto the structure and offer it up to the pins from the first part of
the table top using the biscuits for alignment. Tighten all cam connectors equally and apply cam covers
8
11a
10
11b
9
11 The table top now needs to be secured underneath the structure. Using allen head bolts (11a) and short
furniture bolts (11b), secure the table top to the steel support frame in the fixing locations shown below

Assembly Instructions
Centro Assembly
Please skip to step 20 if your table is not specified with optional power units
12 Now fully tighten the four oak facias using the bolts that were applied in step 5& 6
12

Assembly Instructions
Centro Assembly
For tables with optional power units
13 On the underside of the table locate the cutout(s)
14 Apply the power box to the table using 4 button head bolts
15 Then apply the 2 flat cheeks to the assembly, either side of the power box using 2 button head bolts
and repeat if your table has multiple power cut-outs
13 14 15
16 From above the table thread the cables from 1 power module through the opening, align the power
module with holes in the power box, and use 4 small threaded phillips screws to secure the module in
place using a screw driver
When using a power drill, please select a low torque setting
17 Then secure the power module facia plate with 2 small security screws (see image 17)
Repeat this process for all other power modules
16
18
17
19
18 Use a hand tool to add short M6 furniture bolts to the power box flat cheeks
19 Using the power box cover as reference, screw down bolts until power box cover is flush with the table top

Assembly Instructions
Cable managed leg
Underside cover
To floor box
Cable
Centro Assembly
20
21
20 Fix the underside cover back into place with the screws removed in step 1
21 Your Centro table is now completely assembled

© Connection Seating Limited 2017. All rights reserved.
London Showroom
31 Great Sutton Street,
Clerkenwell,
London,
EC1V 0NA
Tel: [phone]
www.connection.uk.com
Head Office & Showroom
Dogley Mills,
Penistone Road,
Huddersfield,
West Yorkshire,
HD8 0LE
Tel: [phone]
[email protected]
Manchester Showroom
The Old Law Library,
Kennedy Street,
Manchester,
M2 4BY