Connection Hive User manual

www.connection.uk.com
Hive
Assembly Instructions

Assembly Instructions
Preparation
The Hive product is delivered to you in component
form. Before starting the assembly please separate
the boxes into each finished piece.
The labels on the boxes identify the finished piece
that the components relate to, SHVXXX, etc.
The process to assemble the units starts from the
floor up and the following images will assist.
The fixings needed for the generic pieces of Hive are
contained in the bag as shown.
Please note: As this is a general fixing kit, parts may
be left over after assembly.
Components
Fixing kit

Assembly Instructions
Hive Assembly
With the back unit inverted attach the leg rails to the
units using the M8 button head bolts.
The unit can now be placed upright and stored to
one side. Complete this for all the straight pieces.
With the unit inverted attach the leg rails to the units
using the M8 button head bolts
With the foot rails attached to both ends of the back, offer
up the bench unit and secure with M8 button head bolts.
Assembling the base - Straight modules
Assembling the base - Corner modules

Assembly Instructions
Secure the bench and back section together using
the M8 Button head bolts.
The unit can now be placed upright and stored to
one side. Complete this for all the straight pieces.
Offer the joining unit to the piece and secure firmly in
the linking device.
Make sure that the joined pieces are level on the
seats and backs. If not then the linking devices may
not be fully engaged.
Complete linking the units around until the
configuration is complete.
Secure the bench and back section together using
the M8 Button head bolts.
Connecting modules together
Hive Assembly

Assembly Instructions
Insert the screen supports into the glides. Note that
the arrow on the support needs to point downwards.
When in position, the support will click into place.
When aligned loosely, pass a bolt through both
screen supports. The 20mm Workrail linking piece will
engage with the slots cut into the screen supports.
The end cap is secured by positioning the two prongs
into the screen support and aligning with the Workrail.
The end cap is secured in place using a short bolt,
supplied in the fixing kit. Being sure to engage the prongs
on the end cap with the slots in the screen support.
Secure this with a bolt and tighten to pull the
Workrails together.
Place the tool rail over the screen supports. Where
two Workrails are being joined insert a 20mm
Workrail linking piece.
Connecting modules together
Attaching the workrails
Hive Assembly

Assembly Instructions
Hive Assembly
If attaching tables or accessories to your Hive
configuration, then you will need to use the workrail
plate as shown above.
When offering the table up to the fixings they should be guided into place over the pins that go into the cams
already inserted into the table top. If any adjustment is needed in the position of the plate then this can be
done by loosening the bolts and aligning the plate and fixing as required. Once in the correct position the
bolts need to be tightened again.
To use the plate, insert the small twist ‘Fins’ into the
slot in the workrail. Please ensure that fins are inside
the track before starting to tighten the 2 bolts. When
fully tightened, the fins will engage with the track in
the workrail. The image above shows a pin attached
to the workrail ready to accept a table top.
The screens are fitted by lowering them down over
theie respective screen supports. To secure the
screens a custom fitted piece is already attached in
the base and this will engage with the screen support
with a click when in the correct position.
When the complete configuration has the screens
attached the unit will be fully fixed together and
cannot be moved.
Attaching accessories or IWS tables
Attaching screens

© Connection Seating Limited 2017. All rights reserved.
London Showroom
31 Great Sutton Street,
Clerkenwell,
London,
EC1V 0NA
Tel: [phone]
www.connection.uk.com
Head Office & Showroom
Dogley Mills,
Penistone Road,
Huddersfield,
West Yorkshire,
HD8 0LE
Tel: [phone]
[email protected]
Manchester Showroom
The Old Law Library,
Kennedy Street,
Manchester,
M2 4BY