Consort CN1LST Guide

62001096 Iss 04
C ONTROLS
The heater is fitted with a built-in thermostat to control the temperature level to which the
room is heated. The thermostat adjustment knob is located on the right hand end and is
numbered. Rotate the knob clockwise to a higher number to raise the room temperature.
Once set it is unlikely to require to be touched again.
To set the heater to the Frost Watch mode, turn the thermostat control knob
fully anti-clockwise until the frost symbol aligns with mark.
The switches, which are behind the swivel plate on the side panel of the
heater, operate to give: fan only or 1 kW. See Fig 1.
The CN1LSTSW model is fitted with three switches. The two switches
giving 500 watts each.
C ONNECTION TO THE M AIN S UPPLY
Electrical installation should be carried out by a competent installer, preferably registered
with NICEIC (National Inspection Council for Electrical Installation Contracting) in
accordance with the 16 edition of the IEE Wiring Regulations, (BS.7671: 1992), and any
relevant Local Authority Bye-Laws.
This heater is fitted with a 3-core mains supply cable and should be permanently
connected to the electricity supply via a double pole switch having 3mm gap on each pole.
A switched Fused Connection unit to BS.1363. Part 4 is a recommended mains supply
connection accessory to ensure compliance with safety requirements applicable to fixed-
wiring installation.
T HERMAL O PERATED C UT - OUT
The appliance is fitted with an
Electronic Safety Control (ES). This is
a safety device which switches the
heater off if, for any reason, the
appliance overheats. The ES control
must b re-set manually. This must be
done by a competent electrician. The
re-set button is on the ES control
located in the center of the heating
element inside the heater. For
assistance with this, please ring our
helpline (see back page of document).
The heater carries a ‘Do Not Cover’
label to warn the user that if the
appliance is covered, there is a risk of
overheating.
W ALL M OUNTING
The heater must not be located immediately below a fixed socket outlet.
The Wall Mounting brackets are packed separately in the carton. Fit the top mounting
brackets to the wall at the height and centres shown in the diagram. Withdraw the two
feet-securing screws from the base of the heater and use these screws to secure the right-
angled brackets to the base of the rear panel of the heater in the correct holes. These are
the holes in the two protruding lugs.
Mount your appliance onto the top brackets via the two slots in the rear panel. Secure the
bottom bracket to the wall as shown.
WARNING – THIS APPLIANCE MUST BE EARTHED
IMPORTANT – ALWAYS RETAIN YOUR USER INSTRUCTIONS FOR FUTURE REFERENCE.
S AFETY
This equipment has been designed and manufactured to the highest international
standards, but, like all electrical appliances which are operated by mains voltage, care
must be taken if you are to obtain the best results and safety is to be assured.
NOTE: The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience and knowledge unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
•Do NOT site the appliance into a corner when in use.
•Do NOT use this heater in the immediate surroundings of a bath, a shower or a
swimming pool.
•Do NOT handle the appliance with wet hands.
•Do NOT use the appliance in workshops or rooms where excessive dust is
generated or present.
•Ensure that nothing is pushed into any aperture of this appliance.
•Do NOT touch outlet grille when the appliance is in use.
(NB: the LST heaters have a maximum surface temperature of 43
0
C)
•Do NOT cover or restrict any aperture of the appliance when in use.
•Do NOT use the appliance if damaged.
•Do NOT leave the appliance unattended where young children are present.
This appliance meets the requirements of EU Directive 89/336 for EMC.

62001096 Iss 04
I F Y OUR H EATER D OES N OT W ORK
•Check that power is available to the heater. The neon in the control switch should
be illuminated.
•Check that the thermal cut-out has not operated. Follow the reset instructions
given under the section headed ‘Thermal Operated Cut-out’.
•Check that the fuse in the spur unit has not blown. This can be done by replacing
the fuse with another suitable fuse.
Should neither of the above remedies work, then telephone the helpline number shown
in these instructions. (UK ONLY).
•Do not attempt to repair the heater.
C LEANING
Always disconnect the heater from the mains before cleaning.
The heater should not require any maintenance, but it is strongly advised that it is kept
clean. An occasional wipe over with a soft cloth is all that should be necessary.
•Do NOT use metal or furniture polish on any part of the heater
•Do NOT touch the heater with wet hands or in any way bring water into contact
with it.
If the supply cord on this appliance is damaged, it must be replaced by a special cord
which is only available from an Authorised Service Agent, or your supplier.
G UARANTEE
This guarantee is offered to you as an extra benefit and does not affect your legal rights.
All electrical appliances produced for the Company are guaranteed for one year against
faulty material or workmanship. This applies only if the appliance has been used for
purposes in accordance with the instructions provided and has not been connected to an
unsuitable electricity supply, or subject to misuse, neglect, damage or modified or repaired
by any person not authorised by us.
The correct electricity supply voltage is shown on the rating label attached to the
appliance.
C USTOMER H ELPLINE
Should you need any advice on the use of your new Consort product, or should you
require service or repair, please contact our Helpline:


 01646 692172 Mon to Fri 8.30 am to 3.30 pm
Consort Equipment Products Limited
Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT
Tel: [phone] Fax: [phone]
Email: [e-mail] Web: www.consortepl.com
Quality Space Heaters
Using and looking after your
CN1LST, CN1MLST & CN1LSTSW 1 kW
Low Surface Temperature Heaters