Consort CN1LSTRX Original operating instructions

Installation & operation Guide for wirelessly controlled
2kw Low Surface Temperature Fan Heaters
All electrical appliances produced by the Company are guaranteed for one year against
faulty materials or workmanship. This applies only if the appliance has been used for
purposes in accordance with the instructions provided and has not been connected to an
unsuitable electricity supply, or subject to misuse, neglect, damage or modified or repaired
by any person not authorised by us. This guarantee is offered to you as an extra benefit and
does not affect your legal rights.
The correct electricity supply voltage is shown on the rating label attached to the
appliance.
Reasonable care has been taken to ensure that this guide is accurate at the time of
printing. In the interest of progress the Company reserve the right to vary specifications from
time to time without notice.
QUALITY SPACE HEATERS
Models
CN1LSTRX
CN1MLSTRX
62001209 Iss 04

Overview
Please read this guide carefully and retain
for future use and maintenance.
This appliance has been designed and
manufactured to the highest international
standards, however, care must be taken
for optimal results and safety. This
appliance also meets the requirements of
EU Directive 2004/106/EC for EMC and
2009/125/EC Directive.
Safety & Care
Our Low Surface Temperature heaters
have been designed and built to the NHS
requirement for safe surface temperatures
which is that no surface which can be
touched by the user will be more than 43
degrees C (at a room temperature of 21
degrees C.) This means that our Low
Surface Temperature heaters out-perform
the European Standard by a significant
margin. The appliance is not intended for
use by persons (including children) with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for
their safety. Children should be supervised
to ensure that they do not play with the
appliance.
Warning
 Do NOT site the appliance in a corner.
 Do NOT handle the appliance with wet
hands.
 Do NOT use the appliance in workshops
or rooms where excessive dust is
generated or present.
 Ensure that nothing is pushed into any
aperture of this appliance.
 Do NOT touch outlet grille when the
appliance is in use.
 Do NOT cover or restrict any aperture of
the appliance when in use.
 Do NOT use the appliance if damaged.
 Do NOT leave the appliance
unattended where young children are
present.
Thermally Operated Cut-Out
The appliance is fitted with a thermally operated cut-
out (TOC). This is a safety device, which switches the
heater off if, for any reason, the appliance
overheats. The TOC can only be re-set after the
appliance has cooled down. In order to re-set the
TOC, proceed as follows:
 Switch off appliance and leave for
approximately 10 minutes.
 Switch appliance back on and TOC will re-
set.
 Ensure that the appliance is functioning
correctly. If the TOC control operates
again, the appliance should be checked
by a competent electrician.
The heater carries a ‘Do Not Cover’ label to warn
the user that if the appliance is covered, there is a
risk of overheating.
Cleaning
Always disconnect the heater from the mains before
cleaning. The heater should not require any maintenance,
but it is strongly advised that it is kept clean. An
occasional wipe over with a soft cloth is all that should be
necessary.
 Do NOT use metal or furniture polish on any part of the
heater.
 Do NOT touch the heater with wet hands or in any way
bring water into contact with it.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
If Your Heater Does Not Work
 Check that power is available to the heater. The LED
light should be illuminated
 Check that the thermal cut-out has not operated.
Follow the reset instructions given under the section
headed ‘Thermally Operated Cut-out’.
 Check that the fuse in the spur unit has not blown. This
can be done by replacing the fuse with another
suitable fuse.
Should none of the above remedies work, then telephone
the helpline number shown in these instructions (UK ONLY).
Do not attempt to repair the heater.
Connection to the Main Supply
Electrical installation should be carried out by a
competent installer, preferably registered with NICEIC
(National Inspection Council for Electrical Installation
Contracting) in accordance with the 17th edition of the IEE
Wiring Regulations, (BS.7671), and any relevant Local
Authority Bye-Laws. This heater is fitted with a 3-core mains
supply cable and must be permanently connected to the
electricity supply via a double pole switch having 3mm
gap on each pole. There are no exceptions. A switched
Fused Connection unit to BS.1363. Part 4 is a
recommended mains supply connection accessory to
ensure compliance with safety requirements applicable to
fixed-wiring installation.
Note: When switched on for the first time the appliance
may emit a slight smell. This is purely the evaporation of a
fluid used in the manufacturing process.
WARNING: This appliance must be earthed.
2
62001209 Iss 04

3
Controls
When the appliance is connected to the mains
supply and the wall socket is switched ‘ON’ the
mains neon indicator will light, showing that the
power is available to the unit.
Operation
This heater can only be used in conjunction with
a CRXSL wireless programmable controller. Each
CRXSL can control any number of heaters in the
same room.
CRXSL wireless controller
Please refer to the CRXSL installation and control
guide for full operational details.
Wall mounting
The heater must not be located immediately be-
low a fixed socket outlet.
The Wall Mounting brackets are packed sepa-
rately in the carton.
Fit the mounting brackets to the wall at the
height and centers shown in the diagram below
Withdraw the two feet-securing screws from the
base of the heater and use these screws to se-
cure the right-angled brackets to the base of the
rear panel of the heater in the correct holes.
These are the holes in the two protruding lugs.
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: ALWAYS RETAIN YOUR USER INSTRUCTIONS FOR FU-
TURE REFERENCE
62001209 Iss 04
Top brackets

4
CUSTOMER HELPLINE
Should you need any advice on the use of your new Consort product please contact our
Helpline:
Consort Equipment Products Limited
Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT
Tel: [phone] Fax: [phone] Email: [e-mail] Web:
www.consortepl.com
Operation hours: Mon to Thu 8.30am to 4.30pm | Fri 8.30am to 3.30pm
BS EN ISO 9001 Registered Company No FM12671
62001209 Iss 04