Consort PLE200/SS User manual

Installation & Control Guide for Panel Convector Heaters
with Electronic Controls and Open Window Detection
Please note:
‘SS’ suffix added to model number denotes Stainless Steel derivative
Consort Equipment Products Ltd.
Registered Office:
Thornton Industrial Estate, Milford Haven, Pembrokeshire, SA73 2RT
Tel: [phone] Fax: [phone]
Emails: [email protected] | [email protected]
BS EN ISO 9001 Registered Company No FM12671
All electrical appliances produced for the Company are guaranteed for one year against faulty material or
workmanship. This applies only if the appliance has been used for purposes in accordance with the instructions
provided and has not been connected to an unsuitable electricity supply, or subject to misuse, neglect, damage
or modified or repaired by any person not authorised by us. This guarantee is offered to you as an extra benefit and
does not affect your legal rights.
The correct electricity supply voltage is shown on the rating label attached to the appliance.
Reasonable care has been taken to ensure that this guide is accurate at the time of printing. In the interest of
progress the Company reserve the right to vary specifications from time to time without notice.
QUALITY SPACE HEATERS
Models
PLE050/SS PLE075/SS PLE100/SS
PLE125/SS PLE150/SS PLE200/SS
66000852 Iss 02

66000852 Iss 02
Overview
Please read this guide carefully and retain for future use
and maintenance.
This appliance has been designed and manufactured to
the highest international standards, however, care must
be taken for optimal results and safety. This appliance
also meets the requirements of EU Directive 2004/106/EC
for EMC and 2009/125/EC Directive.
Safety & Care
The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities or lack of experience and
knowledge unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
Warning
 Do NOT site the appliance into a corner.
 Do NOT handle the appliance with wet hands.
 Do NOT use the appliance in workshops or rooms
where excessive dust is generated or present.
 Ensure that nothing is pushed into any aperture of this
appliance.
 Do NOT touch outlet grille when the appliance is in
use.
 Do NOT cover or restrict any aperture of the
appliance when in use.
 Do NOT use the appliance if damaged.
 Do NOT leave the appliance unattended where
young children are present.
 If used in a bathroom, the heater is to be installed so
that the switches and other controls cannot be
touched by a person in the bath or shower.
 Operating temperature range -10 to +40 deg.C
Thermally Operated Cut-Out
The appliance is fitted with a thermally operated cut-out
(TOC). This is a safety device, which switches the heater
off if, for any reason, the appliance overheats. The TOC
can only be re-set after the appliance has cooled down.
In order to re-set the TOC, proceed as follows:
 Switch off appliance and leave for
approximately 5 minutes.
 Switch appliance back on and TOC
will re-set.
 Ensure that the appliance is functioning
correctly. If the TOC control operates again,
the appliance should be checked by a
competent electrician.
The heater carries a ‘Do Not Cover’ label to warn the
user that if the appliance is covered, there is a risk of
overheating.
Cleaning
Always disconnect the heater from the mains before
cleaning. The heater should not require any
maintenance, but it is strongly advised that it is kept
clean. An occasional wipe over with a soft cloth is all
that should be necessary.
 Do NOT use metal or furniture polish on any part of the
heater.
 Do NOT touch the heater with wet hands or in any
way bring water into contact with it.
If the supply cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
If Your Heater Does Not Work
 Check that power is available to the heater.
 Check that the thermal cut-out has not operated.
Follow the reset instructions given under the section
headed ‘Thermal Operated Cut-out’.
 Check that the fuse in the spur unit has not blown. This
can be done by replacing the fuse with another
suitable fuse.
Should neither of the above remedies work, then
telephone the helpline number shown in these
instructions (UK ONLY). Do not attempt to repair the
heater.
Connection to the Main Supply
Electrical installation should be carried out by a
competent installer, preferably registered with NICEIC
(National Inspection Council for Electrical Installation
Contracting) in accordance with the 17 edition of the IEE
Wiring Regulations, (BS.7671), and any relevant Local
Authority Bye-Laws. This heater is fitted with a 3-core
mains supply cable and should be permanently
connected to the electricity supply via a double pole
switch having 3mm gap on each pole. A switched Fused
Connection unit to BS.1363. Part 4 is a recommended
mains supply connection accessory to ensure
compliance with safety requirements applicable to fixed-
wiring installation.
Note: When switched on for the first time the appliance
may emit a slight smell. This is purely the evaporation of a
fluid used in the manufacturing process.
WARNING: This appliance must be earthed.
2

66000852 Iss 02
Installation
MILLIMETRES
WATTS A B
PLE050/SS 500 442 303
PLE075/SS 750 442 303
PLE100/SS 1000 614 477
PLE125/SS 1250 720 582
PLE150/SS 1500 720 582
PLE200/SS 2000 852 713
195mm
A
B
Fig. 1
3
See Note 16 for Mounting

When the appliance is connected to the mains
supply and the wall socket is switched ‘ON’, the LED
indicator on the moulding will light up green, showing
that the power is available to the unit. Before you can
use the PLE, it has to be activated by pressing any
control button. The LCD backlight will turn on. To
operate any control button, press within 2 seconds of
activation.
Mode
Temp
ProgTime
SET TIME
PRESS AND HOLD
FOR 5 SECONDS
SET PROGRAMME
PRESS AND HOLD
FOR 5 SECONDS
TEMPERATURE SET
WHEN DISPLAY SHOWS
ROOM TEMPERATURE,
PRESS TO ADJUST
MODE SELECTION
BOOST, MANUAL,
SETBACK AND
PROGRAM
-Press and hold the TIME button for 5 seconds.
Minutes are flashing - use TEMP and MODE
buttons to set minutes.
-Press TIME button
Hours are flashing - use TEMP and MODE
buttons to set hours.
-Press TIME button
Day is flashing - use TEMP and MODE
buttons to set Day.
Once you are happy with the settings, press ‘Time’ to
return to main screen.
1. Basic Operation
2. Time and day setting
3. Selecting operating mode
PLE has 4 operating modes:
BOOST, MANUAL, SET BACK, PROGRAM.
Each mode can be selected by pressing the MODE
button to cycle through the options. The cycle
sequence will always start with BOOST mode followed
by MANUAL, SET BACK and PROGRAM.
5. MAN - Manual Mode
In manual mode, the heater maintains the set
temperature.
1. Use TEMP and MODE to set the temperature.
To amend the set temperature when in Manual
mode, simply activate the display by pressing any
button. Press TEMP, then use TEMP and MODE to
change the temperature. Once the temperature is
set, leave the display to return to the main screen and
the settings will be saved.
4. BOOST - 15 minutes
The boost feature increases the room temperature for 15
minutes.
1. Use TEMP and MODE to set the temperature.
To amend the set temperature when in Boost mode,
simply activate the display by pressing any button. Press
TEMP, then use TEMP and MODE to change the
temperature. Once the temperature is set, you can
leave the display to return to the main screen and the
settings will be saved. After 15 minutes, the PLE will return
to previous operating mode.
In this mode, the PLE will follow the week’s time /
temperature programme.
You can temporarily override the temperature in PROG
mode by simply activating the display and using the
TEMP and MODE buttons to set the new temperature.
The new set temperature will be then maintained until
the next program step.
7. PROG - Automatic time mode
6. SETB - Reduction in programmed temperature
In the setback (ECONOMY) mode, PLE lowers all
temperatures in the 7-day programme by a set value.
You can set how much to lower the programme
temperatures in SETB mode by simply activating the
display, pressing TEMP and using TEMP and MODE to set
the new value.
The display will first show the temperature difference and
after 2 seconds the new set temperature.
4
66000852 Iss 02

8. Set 7-day programme
06:00
10
20
08:00
19ºC
4ºC
ºC
12:00
22ºC
14:00 16:00
16ºC
22ºC
10ºC
22:00
PROGRAM 1 PROGRAM 2 PROGRAM 3 PROGRAM 4 PROGRAM 5 PROGRAM 6
An example of one day programme on PLE
TIME SETTING PROGRAMME SETTING
-SET MINUTES
-SET DAY
-SET HOURS
-SELECT DAY TO SET
-SET MINUTES FOR PROGRAM
-SELECT PROGRAM TO SET
-SET TEMPERATURE FOR PROGRAM
Logic diagram for setting programme on PLE
PROG MODETEMP
1. Press and hold PROG for 5 seconds to enter the
time setting.
2. The day will be flashing.
3. Use TEMP and MODE to navigate day, press
PROG to select day.
4. PROG 1 will be flashing. Use TEMP and MODE to
navigate programme, use PROG to select
programme.
5. The minutes will be flashing.
6. To set minutes, use TEMP and MODE to change
minutes, press PROG to set the minutes.
7. The hour will be flashing
8. To set hour, use TEMP and MODE to change
hour, press PROG to set the hour.
9. The temperature will be flashing.
10. To set temperature, use TEMP and MODE to
change temperature, press PROG to set
temperature.
To add another programme repeat steps 2-10.
The PLE has a 7-day timer with up to 6 programming
steps available for each day. In the programming you
can set a start time and a temperature for each
programme. Each programme has to be used.
9. Advance mode
Press PROG from PROG mode to bring forward the next
programme. To clear advance mode, press PROG.
11 Keys locking
Press and hold TIME and TEMP together for 5 seconds. The
display will show symbol. Repeat the step to unlock.
10. Heat symbol on the display
Every time there is a demand for heat, the display will
show the heat icon.
-reduced heat output when the room temperature is
close to the set temperature.
- full heat output
12. Status light on the heater
Light colour Heater status
STAND-BY No heat output
Reduced heat output
Full power heat output
5
66000852 Iss 02