Contro l4 T4 Series User manual

11
Supported models
• C4-T4T8-xx 8" Tabletop Touchscreen (black or white)
• C4-T4T10-xx 10" Tabletop Touchscreen (black or white)
Introduction
The Control4® T4 Series Tabletop Touchscreens oer complete
system control in an elegant, compact, and portable design. The
touchscreens are equipped with a full capacitive screen, audio
and video Intercom (with the built-in camera) using SIP, and
more.
This touchscreen can be located anywhere, and the convenient
recharging station enables it to be used as either a tabletop or
portable interface. The touchscreen uses an AC power adapter
for power and Wi-Fi for network connectivity.
Note: 802.11b is not recommended for video intercom.
We recommend using Wireless-N. See “Specifications”
for more information.
Box contents
• Tabletop Touchscreen
• Recharging station
• Recharging station power cord
Accessories available for purchase
• Tabletop Permanent Mount Kit (C4-T4PMNT)
• T4 Touchscreen Tabletop 8" Base (C4-T4TBS8)
• T4 Touchscreen Tabletop 10" Base (C4-T4TBS10)
Warnings
Warning! This product must be grounded in accordance
with the National Electrical Code (NEC) requirements.
Avertissement ! Ce produit doit être fondu selon les
conditions électriques nationales de code (NEC).
Caution! Do not place the touchscreen near sources of
heat or expose to direct sunlight for an extended time.
Avertissement ! Ne placez pas l’unité près des sources
de chaleur ou exposition pour diriger la lumière du soleil
pendant une période prolongée.
Caution! This product generates heat. The room must
have adequate ventilation or the ability to dissipate heat
eectively.
Avertissement ! Ce produit produit de la chaleur. La salle
doit avoir à ventilation proportionnée ou la capacité
d’absorber la chaleur ecacement.
Caution! Use this product only in dry locations.
Avertissement ! Employez ce produit seulement dans
des endroits secs.
Caution! Do not use pens or sharp objects to navigate
or make selections on the touchscreen. To select an item
or scroll through a list, use your fingertip.
Avertissement ! N’employez pas les stylos ou les objets
pointus pour diriger ou pour faire des choix sur l’écran.
Pour choisir un article ou un rouleau par une liste,
employez votre bout du doigt.
Caution! Improper use or installation can cause
DAMAGE OF PROPERTY.
Avertissement ! L’utilisation ou l’installation inexacte
peut causer DAMAGE DE PROPRIÉTÉ.
Important! Using this product in a manner other than
outlined in this document voids your warranty. Further,
Control4 is NOT liable for any damage incurred with the
misuse of this product. See “Warranty.”
T4 Series Tabletop Touchscreens
Installation Guide

2
Specifications and requirements
Specifications
Model Numbers C4-T4T10-BL, C4-T4T10-WH
C4-T4T8-BL, C4-T4T8-WH
Screen
Resolution: 1920 × 1200
Capacitive touch
Camera: 720p
Wireless network
802.11b/g/n 2.4 GHz
802.11a/n/ac 5 GHz
Security: WEP, WPA/WPA2 PSK, 802.1x EAP, PEAP
Notes: (1) While technically the touchscreen can use 802.11b,
802.11b is not supported. (2) 802.11n is recommended for
best performance. Even with 802.11n, broadcasting to
several devices will degrade Video Intercom response time
and images. Broadcasting to additional devices will further
degrade performance. See “Wireless Network Limitations.”
Power supply
100-240V AC, 50/60 Hz
International adapters included
Charging base connections: 5V DC power
Dimensions
(W×H×D)
8" Touchscreen: 178 × 130 × 19 mm (7.0 × 5.1 × 0.75")
8" Base: 106 × 79 × 56 mm (4.17 × 3.11 × 2.21")
10" Touchscreen: 245 × 172 × 23 mm (9.65 × 6.77 × 0.91")
10" Base: 115 × 102 × 66 mm (4.53 × 4.02 × 2.60")
Weight
8" Touchscreen: 1.05 lb (0.47 kg)
8" Charging base: 1.4 lb (0.64 kg)
10" Touchscreen: 1.35 lb (0.60 kg)
10" Charging base: 1.05 lb (0.46 kg)
Operating
temperature
0 to 40 ˚C (32 to 104 ˚F)
Storage
temperature
-20 to 70 ˚C (-4 to 158 ˚F)
Requirements
• A controller fully installed and configured with Control4
OS3.2.1 or newer.
• A wireless network (IEEE 802.11b/g/n) must be installed and
available with a wireless access point (WAP). Security can be
WEP, WPA/WPA2 PSK, 801.1x EAP, or PEAP.
• For AC power, you must have access to an AC power outlet
(AC power adapter included).
Views
Front
E
A B C
D
A Camera LED
B Camera
C Light sensor
D Stereo microphones
E 8"or 10" diagonal, capacitive 1920 × 1200 display
Back (with charging station)
C
F
A B
D
E
G
A Power button. Press to enter or exit battery saving mode,
press and hold to turn off or restart, or press and hold for 10
seconds to power off.
B Reset pinhole. Press to reset, or press and hold to reset and
restore factory defaults.
C Docking connector
D Volume buttons
E Speakers
F Charging station base
G 5V DC power connector

3
Touchscreen placement
Place the touchscreen’s charging station on any level surface
near a power outlet. For more information on mounting the
touchscreen, see “Portable” under “Mounting options” below.
Note: Consider the angle of the touchscreen’s camera
and the sitting or standing position of the people who
will use it while it’s on the charging station.
Connect power and Wi-Fi
The touchscreen uses a Wi-Fi network connection, so it can be
positioned anywhere in the home with a strong WiFi signal and
access to a power outlet.
To connect power and Wi-Fi:
1 Place the touchscreen’s charging station near a power outlet.
2 Connect the AC power adaptor to a power outlet and the
charging station.
3 Make sure you have Wi-Fi working in the home.
If a home requires a large number of Wi-Fi video intercom
devices, ensure that you have a robust Wi-Fi network
(possibly consisting of multiple access points).
Connection notes: (1) Video Intercom. Although
this device supports 802.11b/g/n, 802.11 b is not
recommended for Video Intercom use. (2) We
recommend Wireless-N for best performance.
Wireless network limitations: Many Wi-Fi access points
handle Multicasts (Wi-Fi simultaneously sent to multiple
devices, for example, when the touchscreen broadcasts
video to all stations) by slowing down transmission
speed to the 1 Mb basic rate. This can cause overall
Wi-Fi congestion in the Wi-Fi network during the
broadcast. Video Intercom response times and images
may degrade at each device.
Connect to Wi-Fi
To set up Wi-Fi on the touchscreen:
1 After the touchscreen starts up, tap Network. The network
configuration page opens.
2 Under Wi-Fi, tap or slide OFF/ON to enable Wi-Fi, then tap
the Wi-Fi field to open a list of available networks.
3 Tap the network name you want to connect to.
4 Tap the Password field, then use the on-screen keyboard to
type the password (if required).
Note: If you need to enter a static IP address, follow the
instructions under “To set a wireless static IP address”
below before proceeding.
5 Tap Connect.
If you don’t see the network you want:
1 Tap +, then tap the Network SSID field and type the SSID
(name) of the network by using the on-screen keyboard.
2 Tap the Security field, then select the type of security to use.
3 Tap the Password field, then use the on-screen keyboard to
type the password (if required).
Note: If you need to enter a static IP address, follow the
instructions under “To set a wireless static IP address”
below before proceeding.
4 Tap Save. The new network is added to the bottom of the
network list.
To set a wireless static IP address:
1 Scroll down and tap Show advanced options.
2 Tap IPsettings, then tap Static.
3 Select each box one at a time and use the on-screen
keyboard to type the:
• IP address
• Gateway
• Network prefix length
• DNS 1 (preferred)
• DNS 2 (alternate)
Add and configure in Composer Pro
After the touchscreen is installed and appears on the home
network, use Composer Pro to add it to the Control4 system and
configure it.
Use the Composer Pro System Design and Connections views to
add and configure this device.
To add and configure a T4 touchscreen to a project:
1 Add the T4 Tabletop Touchscreen driver to your project.
2 Identify the device to the project, select the touchscreen in
Composer Pro’s Connections > Network view, click Identify,
then tap Identify on the touchscreen.
3 To configure the properties, select the touchscreen in the
System Design view, then view and change the properties in
the Properties pane as needed.
Properties include:
• Network Connection—Reports the touchscreen’s current
network connection type.
• Back Light—Click the arrows or type numbers to set the
light level, then click Set.
Advanced properties include:
• Enable Camera—Allows you to enable or disable the
camera.
Intercom (nested under the touchscreen) properties:
• Appearance—Select to hide the touchscreen from
appearing in Navigators as an available device.
• Behavior—Select the modes you want this touchscreen to
support.
• Audio Control—Select the volume of individual audio
settings.

4
• Sip Information—Information for integrating the
touchscreen into your SIP/VoIP system.
• Custom Buttons—Select to enable and label the two
available custom buttons.
• Alternate Camera—Select to use an external camera for
the video associated with the touchscreen, for example, a
security camera mounted to the side of the entrance and
pointing at the door.
Mounting
Place the charging station on any level surface. While positioning
the touchscreen, consider the angle of the touchscreen’s camera
and the position of the people who will use it while it’s on the
charging station.
Portable use
You can set the touchscreen onto the charging station for
recharging and tabletop use, and lift the screen from the
charging station for portable use (like a tablet).
Tip: For easy and smooth separation of the touchscreen from the
charging station, slightly rotate the touchscreen while lifting it.
Permanent mount
You can mount a touchscreen permanently to a surface, such
as a table, using the optional T4 Tabletop Permanent Mount Kit
(C4-T4PMNT).
1 Peel o the plastic cover on the touchscreen’s docking
connector recess.
2 Use the Phillips-head flat screws provided in the kit to
install the permanent-mount adapter into the touchscreen’s
docking connector recess.
3 Remove the charging station’s bottom cover by removing
the two screws shown.
Base
screws
4 Save the cover and screws.
5 Using a #2 Phillips screwdriver inserted from the base of
the charging station, remove the two screws that secure
the charging station’s top docking connector cover (do not
remove the screw holding the PCB), then discard the two
screws you removed.
6 Screw the base to the back of the touchscreen as shown
using the new threaded, black screws provided. DO NOT
ATTEMPT TO USE THE ORGINAL SCREWS REMOVED
IN STEP 5 OR YOU WILL PERMANANTLY DAMAGE THE
THREADS ON THE TOUCHSCREEN.
7 Reinstall the base bottom cover.

5
8 To install the charging station permanently into a table
or countertop, remove the small rubber discs covering the
threaded holes in the base.
9 Install the threaded posts (all thread) into the base of the
charging station.
10 Using the template and a 1/4" drill, drill two holes into the
surface where you are mounting the touchscreen. Maximum
surface thickness is 32 mm (1.25").
11 Mount the charging station assembly into the mounting
holes and secure it in place using a washer and nut.
Troubleshooting
To power cycle the touchscreen:
1 Press and hold the (power) button for several seconds
until the touchscreen turns o.
2 Press and release the (power) button again to turn on.
To perform a factory data reset:
1 On the touchscreen’s main screen, tap Settings, System Info,
then Factory data reset.
- OR -
If the touchscreen has not yet been configured, tap About,
then Factory data reset.
- OR -
To reset without using the display screen:
a Dock the touchscreen onto its charging station.
b Press and hold the volume up button while using a
straightened paper clip to press and release the reset
button.
Reset hole
c Keep holding down the volume up button until the icon
below appears on the screen, then release the button.
d A message appears, indicating that data is being erased.

control4.com | 888.400.4070
Additional resources
The following resources are available for more support.
• Knowledgebase and forums on Tech Community
• Technical Support
• Control4 website:
www.control4.com
• Composer documentation available at ctrl4.co/docs .
Warranty and legal notices
Find details of this product’s 2-Year Limited Warranty at
snapav.com/warranty , or request a paper copy from Customer
Service at [phone]. Find other legal resources, such as
regulatory notices and patent information, at snapav.com/legal .
More help
For the latest version of this document, open this URL or scan
the QR code on a device that can view PDFs.
200-00683-A
2020-10-09 MS
Copyright ©2020, Wirepath Home Systems, LLC. All rights reserved. Control4 and Snap AV and their respective logos are registered trademarks or trademarks of
Wirepath Home Systems, LLC, dba “Control4” and/or dba “SnapAV” in the United States and/or other countries. Snap AV and Wirepath are also registered trademarks
or trademarks of Wirepath Home Systems, LLC. Other names and brands may be claimed as the property of their respective owners. All specifications subject to change
without notice. A
LATEST VERSION OF THIS DOCUMENT
ctrl4.co/t4-tabletop-ig
T4 DATA SHEET
ctrl4.co/t4-ds

11
Supported models
• C4-T4IW8-BL 8" T4 In-Wall Touchscreen, Black
• C4-T4IW8-WH 8" T4 In-Wall Touchscreen, White
• C4-T4IW10-BL 10" T4 In-Wall Touchscreen, Black
• C4-T4IW10-WH 10" T4 In-Wall Touchscreen, White
Introduction
The Control4® T4 Series 8- and 10-inch In-Wall Touchscreens oer
complete system control in an elegant and compact design. The
touchscreens are equipped with a full capacitive screen, audio
and video Intercom (with the built-in camera) using SIP, and
more.
This touchscreen works great in either new construction or
retrofit installations. For power and network connectivity, choose
from three options:
• Ethernet with PoE—The Ethernet network connection is
provided through the PoE Injector. No additional wiring is
needed.
• Ethernet with AC—Connect the touchscreen to one of the
LAN ports on the gateway/router using an Ethernet cable.
AC power is used to power the touchscreen.
• WiFi with AC—The internal Wi-Fi will communicate with the
LAN’s wireless AP, so no additional network wiring is needed.
AC power is used to power the touchscreen.
Note: 802.11b is not recommended for video intercom.
We recommend using Wireless-N. See “Specifications”
and “Power and Network Installation Options” for more
information.
Box contents
• 8"or 10"T4 In-Wall Touchscreen
• Power box (to power the touchscreen)
• Two screws (to attach the power box to the wall box)
• Set screw (to secure the touchscreen to the power box)
• Set screw tool (3/32" hex wrench)
Accessories available for purchase
• Pakedge 802.3at/af Gigabit PoE+ Injector (PI-30AT), or
Araknis Networks Gigabit PoE+ Injector
(AN-ACC-INJ-POE-30W), each sold separately.
• Wall box options (sold separately)—Metal and plastic, for
new construction or retrofit installations.
• In-Wall Touchscreen Wall Box Kits - New Construction
• Plastic (C4-NWB57C-P)
• Metal (C4-NWB57C-M)
• In-Wall Touchscreen Wall Box Kits - Retrofit
• Plastic (C4-RWB57C-P)
• Metal (C4-RWB57C-M)
For wall box installation details, see:
• In-Wall Touchscreen Wall Box Installation Guide-New
Construction (
ctrl4.co/wallbox-new )
• In-Wall Touchscreen Wall Box Installation Guide-Retrofit
(
ctrl4.co/wallbox-retro )
8"and 10"T4 Series In-Wall Touchscreen
Installation Guide

2
Warnings
Warning! The touchscreen must be protected by an
external circuit breaker or a fuse rated at 6A maximum
when used in Europe.
AVERTISSEMENT ! Pour réduire le risque du feu ou de
choc électrique, n’exposez pas cet appareil à la pluie ou
à l’humidité.
Warning! Do not place the touchscreen near sources of
heat or expose to direct sunlight for an extended period
of time.
AVERTISSEMENT ! Ne placez pas l’unité près des
sources de chaleur ou exposition pour diriger la lumière
du soleil pendant une période prolongée.
Warning! Install in accordance with all national, state,
and local electrical codes.
AVERTISSEMENT ! Installez selon tous les national, état,
et codes électriques locaux.
Warning! This product generates heat. The room must
have adequate ventilation or the ability to dissipate heat
eectively.
AVERTISSEMENT ! Ce produit produit de la chaleur.
La salle doit avoir à ventilation proportionnée ou la
capacité d’absorber la chaleur ecacement.
Warning! This product must be grounded in accordance
with the National Electrical Code (NEC) requirements.
AVERTISSEMENT ! Ce produit doit être fondu selon les
conditions électriques nationales de code (NEC).
Warning! Use this product only in dry locations.
AVERTISSEMENT ! Employez ce produit seulement dans
des endroits secs.
Caution! Do not use pens or sharp objects to navigate
or make selections on the touchscreen. To select an item
or scroll through a list, use your fingertip.
AVERTISSEMENT ! N’employez pas les stylos ou les
objets pointus pour diriger ou pour faire des choix sur
l’écran. Pour choisir un article ou un rouleau par une
liste, employez votre bout du doigt.
Caution! Improper use or installation can cause
DAMAGE OF PROPERTY.
AVERTISSEMENT ! L’utilisation ou l’installation inexacte
peut causer DAMAGE DE PROPRIÉTÉ.
Important! Using this product in a manner other than
outlined in this document voids your warranty. Further,
Control4 is NOT liable for any damage incurred with the
misuse of this product. See “Warranty.”
Important ! Utilisant ce produit en quelque sorte autre
que décrit dans ce document vide votre garantie. De
plus, Control4 n’est pas responsable d’aucun dommage
encouru avec l’abus de ce produit. Voyez que «
Warranty. »
Specifications and requirements
Specifications
Model Numbers C4-T4IW10-BL, C4-T4IW10-WH,
C4-T4IW8-BL, C4-T4IW8-WH
Screen Resolution: 1920 × 1200, capacitive touch
Camera: 720p
Network
Ethernet or Wi-Fi
• 802.11b/g/n 2.4 GHz
• 802.11a/n/ac 5 GHz
• Security: WEP, WPA/WPA2 PSK, 802.1x EAP, PEAP
Notes: (1) While technically the touchscreen can
use 802.11b, 802.11b is not supported. (2) 802.11n
is recommended for best performance. Even
with 802.11n, broadcasting to several devices will
degrade Video Intercom response time and images.
Broadcasting to additional devices will further
degrade performance. See “Wireless Network
Limitations.”
Power supply PoE (IEEE 802.3af) 13 W peak
100-240V AC, 50/60 Hz
Dimensions (W × H × D)
8" model: 175 × 127 × 13 mm (6.9 × 5.0 × 0.53")
10" model: 239 × 165 × 13 mm (9.4 × 6.5 × 0.53")
Wall box: 68 × 104 × 61 mm (2.7 × 4.1 × 2.4")
Power box: 71 × 114 × 46 mm (2.8 × 4.5 × 1.8")
Weight (with mid-box) 8" model: 0.41 kg (0.9 lb)
10" model: 0.68 kg (1.5 lb)
Operating temperature 0 to 40 ˚C (32 to 104 ˚F)
Storage temperature -20 to 70 ˚C (-4 to 158 ˚F)
Requirements
• A controller fully installed and configured with Control4
OS3.2.0 or later.
• Control4 Touchscreen wall box installed. See “Accessories.”
• If using Ethernet with PoE power:
• Ethernet network installed and available that includes a
gateway/router/switch
• Control4 PoE Injector (model #AC-POE1-B) or another
third-party, UL/ANSI-certified PoE injector or switch.
• Two Ethernet Cat 5/6 cables: (1) one that runs from the
Ethernet gateway/router/switch to the PoE injector/switch
and (2) one that runs from the PoE injector/switch to the
Ethernet connection in the touchscreen’s wall box.
• If using Ethernet with AC power:
• Ethernet network installed and available that includes a
gateway/router/switch
• Access to in-wall AC power (neutral connection required)
• One Ethernet Cat 5/6 cable that runs from the Ethernet
gateway/router/switch to the touchscreen
• A 14-gauge electrical wire long enough to pull between
the touchscreen and the power source
• If using Wi-Fi with AC power:
• Wireless network (IEEE 802.11b/g/n) installed and
available with a wireless access point (AP). Security can
be WEP, WPA/WPA2 PSK, 801.1x EAP, or PEAP.
• Access to in-wall AC power (neutral connection required)
• A 14-gauge electrical wire long enough to pull between
the touchscreen and the power source

3
Front view
E
A B C
D
A Indicator LED (startup, camera in use, audio listening)
B Camera
C Ambient light sensor
D Stereo microphones
E 8”or 10” diagonal, capacitive 1920 × 1200 display
Back view
D
CB
G
E
F
A
A Reset pinhole buttons-For resetting and restoring the
touchscreen to factory default settings.
B Upper mount tab
C Power—Press this button to turn the touchscreen on, or press
and hold it to turn the touchscreen o.
D Docking electrical connector
E Locking tab
F Set screw—secures the touchscreen to the power box.
G Stereo speakers
Top view
A B C
A Power button. Press to turn the display on and off, press and
hold to select Power off or Restart, or press and hold for 10
seconds to reset the device.
B Center pinhole. Not used.
C Reset pinhole. Press to reset, or press and hold until “Erasing”
appears on the screen to restore factory defaults.
Touchscreen placement
Place the touchscreen in a convenient location at eye level,
typically near the entrance of the room, about 145 to 155 cm
(57to61 inches) from the floor (Figure 3).
Note: Consider the camera on the panel and the height
of the people in the home who will use the camera for
Video Intercom.
Important: The top of the touchscreen must be
mounted no higher than 2 m (6.6 ft.) above the floor.
Figure 1: Touchscreen placement
LED indicator
The LED on the touchscreen indicates the camera status of the
camera and booting information as described in the next table.
Camera/LED color state Touchscreen status
O Camera is o
Green Camera is on
Green (blinking slowly) Touchscreen is booting
Installation
Warning! Before installing the touchscreen, switch o
the circuit breaker or remove the fuse from the fuse box.
AVERTISSEMENT ! Pour l’endroit où vous installez
l’écran tactile, coupez le disjoncteur ou enlevez le fusible
de la boîte de fusible.
Important! Before you can complete the instructions
below, you must have an 8"or 10"Touchscreen wall box
installed according to the documentation provided in
the wall box kit. See “Accessories” for details.
Important ! Avant de lire les instruction ci-dessous,
il vous faut un support mural installé suivant la
documentation fournie avec le kit du support mural. Plus
de détails dans la partie << Accessoires >>.
Important! When cutting the opening for the wall box,
do not cut the opening too large. Be conservative and
cautiously enlarge it as needed.
Important ! En coupant l’ouverture pour le support
mural, ne faites pas une ouverture trop grande. Soyez
prudent, et agrandissez la avec précaution.
Touchscreen
AC power
(unless using PoE)

4
Power and network installation options
This device uses an Ethernet or Wi-Fi network connection and
can be powered using PoE or AC power.
Choose one of the following options to install the power and
network communication.
Caution! Do not attempt to use PoE and AC power at
the same time. Choose only one power option.
ATTENTION ! Ne pas tenter d’utiliser PoE et AC en
même temps. Choisir une seule option d’alimentation.
Option 1: Ethernet connection with PoE
PoE supplies DC power on the Ethernet cable using a PoE
Injector (model #AC-POE1-B) or a third-party PoE solution to
provide the touchscreen with power and a network connection.
The touchscreen works with the Control4 PoE Injector or a third-
party PoE Injector.
To set up your PoE and Ethernet connection with a PoE Injector:
1 Attach the PoE Injector according to the instructions in your
PoE’s installation guide if provided. Control4 PoE Injector
instructions are provided later in this document.
2 Pull the Ethernet cable from that location to where you want
to install the touchscreen.
Figure 2: Ethernet with PoE—Requires Ethernet connection to PoE
injector
Option 2: Ethernet connection with AC
The Ethernet is connected directly to the switch (Figure 5). This
power connection requires both neutral and hot connections.
Figure 3: Ethernet—Requires a connection to Ethernet and AC power
Option 3: Wi-Fi connection with AC
Place the touchscreen above a power source, for example, an
outlet. Ensure that you have Wi-Fi in the home (Figure 6).
Important: The touchscreen cannot connect to a Wi-Fi
network when already connected by Ethernet.
Notes: (1) Video Intercom. Although this device
supports 802.11b/g/n, 802.11 b is not recommended for
Video Intercom use. (2) We recommend Wireless-N for
Video Intercom. See the Composer Pro User Guide for
details about the touchscreen’s properties.
Wireless Network Limitations: Many Wi-Fi Access Points
handle Multicasts (Wi-Fi simultaneously sent to multiple
devices, for example, when the touchscreen broadcasts
video to all stations) by slowing down transmission
speed to the 1 Mb basic rate. This can cause overall
Wi-Fi congestion in the Wi-Fi network during the
broadcast. Video Intercom response times and images
may degrade at each device.
If a home requires a large number of Wi-Fi Video
Intercom devices, ensure that you have a robust Wi-Fi
network (possibly consisting of multiple access points).
Figure 4: Wi-Fi—Requires AC power and AP
Power installation
Prepare the plastic power box for installation into the wall box by
inserting either the Ethernet cable or the AC power cable into the
power box, and then follow the instructions.
Connecting PoE
Connect the PoE injector to power and the network, and then
connect it to the power box. It can be located anywhere along
the cable that connects the power box to the network switch.
To install a Control4 PoE injector:
1 Connect the Control4 PoE injector to an AC outlet using the
power cord.
2 Connect one of the LAN ports on the network switch to the
PoE Injector’s LAN port using Cat 5/6 Ethernet cable.
3 Pull a cable going from the PoE injector’s PWR LAN-OUT
port through one of the touchscreen’s left-side wall box
knockout holes.
4 Go to “Connecting to a wired network” below.
Place touchcreen here
Controller
Switch
Wireless
access point
WiFi