Converters.TV 15325 User manual

HDBaseT 2×8 HDMI over CAT5e/6/7
Switch Splitter with LA Serving # 15325
Operation Manual

Introduction
The HDMI over HDMI and CAT5e/6/7 Transmitter can support resolutions up
to 1080p ull HD, 4Kx2K timing, 3D and multi-channel digital audio formats
to one HDTV and eight CAT5e/6/7 outputs.
The HDMI can be connected to HDMI display for instant nearby display and
the CAT5e/6/7 can be connected to CAT5e/6/7 to HDMI Receivers for
distance up to 100 meters. urther, a total of 100Mbps Ethernet transmission
rate allows all connected device to share the Ethernet service and the PoE
function free the power shortage issue from the Receiver end
Applications
• Household entertainment sharing and control
Lecture room display and control
Showroom display and control
Meeting room presentation and control
Classroom display and control
Features • HDMI with 3D & 4Kx2K supported, HDCP and DVI compliant
The HDMI and CAT5e/6/7 outputs are playing the same source
simultaneously
Supports one HDMI and eight CAT5e/6/7 outputs
Supports data rate from 250Mbps up to 3Gbps
Supports wide range of PC resolutions from VGA to WUXGA
and HDTV resolutions up to 4Kx2K (3840x2160@24/25/30Hz and
4096x2160@24Hz)
Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-
HD Master Audio transmission (32-192kHz sample rate)
Supports distances up to 100 meters through CAT5e/6/7 cables
Supports Ethernet transmission rate up to 100Mbps
Can select Standard or TV EDID
Supports USB service port
The 3D signal display follow by display TV’s EDID
Supports PoE with capable Receiver units
Supports Bi-directional IR control
Note:
1. This system was tested with CAT6/23AWG cables, results may vary
with cables of a different specification.
2. The PoE function is designed for powering compatible Receiver units
only non-PoE Receivers will need their own power supply. Receivers
of another brand may not be compatible.
3. Displaying HDMI 4Kx2K resolution require the standard 4Kx2K
HDMI cable and display in order for proper image displaying

System
Requirements
•Source equipment with HDMI output connector
Display TV/Monitor with HDMI input connector
HDMI over CAT5e/6/7 Receivers with industry CAT5e/6/7 cables
.
Operation  Front Panel
Controls and
Functions
1. IR Window:
Receive IR signal from the package included remote control only.
2. POWER Button & LED:
Press this button to switch ON or set the device to standby mode and the
LED will illuminate in Green and Red.
3. SYNC:
This LED will illuminate when the HDMI input port connected to the source.
4. HDMI IN 1/2:
Press the button to selection HDMI input source 1 or 2.
The LED will illuminate according to the selection.
5. HDMI & CAT OUT LIN 1~8:
These link LEDs will illuminate when HDMI or CAT5e/6/7 output(s) has
been connected to the Display/ Receiver(s) and the Receiver(s) has
connected with display that shows image on screen
Rear Panel
1. CAT5e/6/7 OUT 1~8:
Connect these ports to CAT5e/6/7 to HDMI Receivers (with or without PoE
function) with CAT5e/6/7 cable to extend the signal up to 100m.

2. IR OUT:
Connect with IR Blaster to blast out the IR signal received from the Receiver
side. Place the IR Blaster in direct line-of-sight of the equipment to be
controlled.
3. IR IN:
Connect with IR Extender to receive IR signal from Transmitter side and
blast out at Receiver side. Ensure that remote controller being used is within
the direct line-of-sight of the IR Extender.
4. LAN:
Connect to intranet or internet service system for a total sharing rate of
100Mbps within the link of Transmitter.
Warning:
DO NOT connect this slot with any of the CAT5e/6/7 port, doing so ay
trigger a power shot down and ruin the device.
5. L/R OUT:
Connect to active speaker or audio equipment for audio signal output.
6. OPTICAL OUT:
Connect to active speaker or audio equipment for audio signal output.
7. HDMI OUT:
Connect to HDMI display for instant image display or cascade with another
family type Transmitter.
8. HDMI IN1/2:
Connect with source equipment such as DVD/Blu-ray or PS3 player.
9. EDID STD/TV:
The default factory setting is on TV, leave as it is when the display is
properly. The unit will detect first the HDMI output’s EDID and send out the
signal accordingly to other output ports. If the HDMI output port is not
connected the device will detect the 1st CAT5e/6/7 output's EDID and send
out the signal accordingly to all outputs.
This device obtain the last memory function therefore, the device will use
the last HMDI output port/the 1st CAT5e/6/7's output EDID after power
cycling or switch in between the EDID setting.
Switch to STD to use build-in EDID if the display has problem. STD EDID's
video at 1080p@60Hz and audio at LPCM 2CH.
10. SERVICE:
This slot is reserved for factory service only.
11. RS-232:
Connect this slot from PC/Laptop for RS-232 command sending.
12. DC 24V:
Plug the 24V DC power supply into the unit and connect the adaptor to an
AC outlet

IR Cable Pin
Assignment
Remote Control
1. Power:
Press the button to turn On/Off the unit.
2. Input Selection 1/2:
Press 1/2 to select HDMI input sources 1 or 2
RS-232 Pin
Definition
Pin Define Tx/Rx
 
 
 
 
 
 
 
 
 
Baud Rate: 115200bps low Control: None
Data bit: 8 bits Stop Bit: 1
Parity: None