Converters.TV 757 User manual

1 by 2 HDMI v1.3 Splitter
- ID# 757
Operation Manual

Introduction
This HDMI v1.3 Distribution Amplifier is an incredibly useful solution for your HDMI
signal distributing needs. From a single HDMI source you can transfer Deep
olor (10-bit and 12-bit) video and a new lossless compressed (Dolby TrueHD,
Dolby Digital Plus and DTS-HD Master Audio) digital audio with high bandwidth
up to 225MHz (6.75Gbps) to two HDMI outputs. Besides splitting and distributing,
it also does signal amplification and equalization, providing high I/O
performance on both audio and video.
Application
 Simultaneous display one HDMI source on 2 TVs
 Show room display control
 Educational demo
 Installation usage
System
Requirements
 Input source equipments with HDMI output connector(s)
 Output displays with HDMI input connector(s)
Features
 HDMI 1.3, HD P1.1 and DVI1.0 compliant Receiver .
 Deep color video up to 12bit, 1080p@(24/60)Hz.
 Simultaneously displays one HDMI source onto eight HDMI displays.
 HD P keysets allow each output to work independently when connecting
to an HDMI display.
 Allows a single HDMI source to be shown on two displays without any
signal loss.
 Supports DVI source/display via HDMI to/from DVI adaptor cable.
 Supports LP M 7.1 H, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master
Audio transmission (32-192kHz Fs sample rate).
 Supports a wide range of P and HDTV resolutions from VGA to UXGA
and 480i to 1080p.
 HDMI cable distance testing showed that with 1080p/8bits resolution: the
Input/Output source can reach up to 10/10 meters away, and at 1080p/12bits
the I/O source can reach up to 6/10 meters.
Note:
A. able tested with AT-6E /23AWG/ using cables of another type may result
in a different operating distance.
B. able distance test included the following: PS3 120G and 37" Samsung
12-bit L D TV.
. Figures provided in this manual are reference figures only, actual
figures may depend on source and display use with cable specification.
 Supports EDID bypass, xvY and E bypass.
 E function support includes one touch play & record, timer
programming, menu language, deck & device menu control, OSD display,
device OSD transfer, remote control pass through, system audio control and
system standby
 System standby will only be actived when the last TV is switched to
standby

Operating Functions
and
Controls
Front Panel
① Sync LED: When an HDMI source is connected, this LED will switch on once
the splitter has established a Link with the source.
②Power LED Indicator: The LED Will turn on when power is on.
③Power Switch: Press this button to turn power on and off.
Rear Panel
① HDMI Inp t: This slot is where you connect the output port of your HDMI/ DVI
source (i.e., DVD, set-top box) using an HDMI/HDMI to DVI adaptor cable.
②HDMI o tp t 1~2: These slots connect to the HDMI displays through the
splittler, using HDMI cables. If more than one output is connected, all
corresponding HDMI outputs will simultaneously display an identical video
signal.
③Power: This slot is where you insert the 5V D power supply after its plugged
into an A outlet.

Connection and
Installation
Speci ications
Frequency Bandwidth 2.25Gbps (single link)
Input Port 1x HDMI female port (Type A onne tor)
Output Ports 2x HDMI female ports (signal link)
HDMI Cable In 1080p 8-bit (10M), 12-bit (15M)
HDMI Cable Out 1080p 8-bit (6M), 12-bit (15M)
ESD Protection Human body model:
± 10kV (air-gap dis harge)
± 6kV ( onta t dis harge)
PCB Stack - up 4-layer board impedan e ontrol
– differential 100Ω
– Single 50Ω
Input TMDS Signal 1.2 Volts (peak-to-peak)
Input DDC Signal 5 Volts (peak-to-peak, TTL)
HDMI Output Resolution 480i ~ 1080p, 1080p24, VGA ~ UXGA
Power Supply 5VDC/1A (US/EU standards, CE/FCC/UL
ertified)
Dimensions (mm) 145(W) x 90(D) x 32(H)
Weight(g) 160
Chassis Material Plasti
Silkscreen Color Bla k
Operating Temperature 0°C ~ 40°C / 32°F~ 104°F
Storage Temperature -20°C ~60°C / -4°F ~ 140°F
Relative Humidity 20% ~ 90% RH (non- ondensing)
Power Consumption 3.2W (max)