Converters.TV 15155 User manual

Multi-Sources to SDI/HDMI Scaler
Box - ID# 15155
Operation Manual

Introduction
The HDMI/PC/Component/CV to SDI/HDMI Scaler allows you to upscale
HDMI/PC/Component/Composite signals to high efinition vi eo of HDMI formats
(720p@50/60 Hz or 1080p@50/60 Hz) an SDI formats (HD-SDI SMPTE 292M or 3G-
SDI 424M/425M), then output to both ports at the same time. Besi es scaling features, the
evice also carries functionalities for it to serve as control center of vi eo wall up to
15×15 total 225 isplays showing one single picture together
Features
●Supports HDMI, PC, Component an Composite Vi eo input signals
●Supports SDI an HDMI output simultaneously
●Supports SDI output istance up to 100 meters (3G-SDI), or 200 meters (HD-SDI)
an 300 meters (SD-SDI)
1. Scales any input signal to the following output signals: HDMI: 720p@50/60
Hz or HD-SDI: SMPTE 292M (1.485 Gbit/s)
2. HDMI: 1080p@50/60 Hz or 3G-SDI: SMPTE 424M/425M (2.970 Gbit/s)
●Supports HDMI input timings: VGA@60 ~ WUXGA@60 Hz (RB) & 480p/576p ~
1080p@50/60 Hz
●Supports VGA input timings: VGA@60 ~ WUXGA@60 Hz (RB) & 1920×1080@60
Hz
●Supports Component input timings: 480i/576i ~ 1080i/p@50/60 Hz
●Supports Composite Vi eo input timings NTSC, PAL
●Supports vi eo wall controlling
Note: Tested with Belden 1694A cable. Results may vary with cables that have a different
s ecification.
Applications
●Simultaneous output on HDMI an SDI isplay
●Up-scales vi eo resolution to HD output isplay
●TV/Vi eo/Display/Gaming/Movie wall isplay
●Combination a vertising wall
System Requirements
●HDMI/PC/Component/Composite input source signal an connection cables, output
isplay HDMI & SDI monitors with connection cables.
●Or HDMI/SDI splitter with connection an RS-232 cables, output isplay TV wall
with connection cables.

Operation Controls
and Functions
Front Panel
1. PO ER
Press this button to switch on the evice(s). All the connecte Vi eo wall system control
evice(s) will be switch to ON.
2. IR Remote Control Sensor
3. MENU
Press this button to enter into the OSD menu.
4. DO N
a. Press the DOWN button to move own the selection in the OSD menu an value.
b. When in Picture Menu, press DOWN button to show the in ivi ual setup sli e bar an
continue press the button to re uce the value.
c. Press the DOWN button irectly to a just the au io volume own.
Note: Audio volume adjustment not functional when HDMI source in ut.
5. UP
a. Press the UP button to move up the selection in the OSD menu an value.
b. When in Picture Menu, press UP button to show the in ivi ual setup sli e bar an
continue press the button to increase the value.
c. Press the UP button irectly to a just the au io volume up.
Au io volume a justment not functional when HDMI source input.
6. ENTER
a. Press ENTER to confirm the selection.
b. When in Picture Menu, press ENTER button to move own the cursor.
7. INPUT
a. Press to select the input sources.
b. When enter the OSD menu, press INPUT button to exit the setup.
Note:Points a/b/c efines multiple usage of the key button.

Back Panel
1. SDI/HDMI OUT
These slots are where you connect the SDI/HDMI isplay. Both slots are output
simultaneously.
2. HDMI IN
Connect the HDMI input port to the HDMI/DVI output ports of your source equipment
such as DVD/Blu-ray player or set-top-box.
3. PC with PC AUDIO IN
Connect the PC/au io input port to the PC/au io output port of your source equipment
such as Laptop or PC.
4. Component with R/L IN
Connect Component an R/L input port to the component an R/L output port of your
source equipments such as DVD/Blu-ray player or set-top-box.
5. Video with R/L IN
Connect Vi eo an R/L input port to the Vi eo an R/L output port of your source
equipments such as DVD player or set-top-box.
6. RS-232 IN
As a first evice of the vi eo wall system, this slot is to connect with PC/NB equipment
for RS-232 control. Starting from the secon evice of the vi eo wall system, this slot
shoul be connecte from the RS-232 out of the last evice. For etail RS-232 comman s
please refers to section 8.
Note: For RS-232 control it required a s ecial level-shift board and it is an o tional
accessory selection.
7. RS-232 OUT
This slot is to connect to the next vi eo wall control system’s RS-232 IN.
8. IR IN
This slot is to connect with IR receiver inclu e in the package for receiving the IR signal
of the evice’ remote controller.
9. Power
Plug the DC 5V power supply into the system an connect the a aptor to AC wall outlet.

OSD Menu
Main Menu 2nd Layer
MAIN MENU PICTURE MENU*1 STANDARD ON/OFF
R OFFSET 0~255 (118)
G OFFSET 0~255 (116)
OFFSET 0~255 (118)
R GAIN 0~255 (098)
G GAIN 0~255 (098)
GAIN 0~255 (098)
CONTRAST 0~63 (50)
RIGHTNESS 0~63 (40)
SETUP MENU*1 LANGUAGE ENG / T.CHINESE
(ENG)
HDMI SOUND ON/OFF (ON)
STANDARD ON/OFF (ON)
H POSITION START 000~385 (*2)
V POSITION START 000~53 (*2)
H lanking Edit 0~255 (20)
V lanking Edit 0~255 (20)
TV Option Width 1~15 (1)
TV Option Height 1~15 (1)
*Note:
1. The Picture Menu allows users to adjust single monitor’s setting while the Setup Menu
will only needs to be adjust once and all monitors will be automatically adjusted.
2. Suggest to set the SETUP ME U's STA DARD to O after a change of the timings to
obtain the best position.
Picture Standard: Set it to O will allow system to set the picture menu into the default
value as indicated in the ( ).
Picture R/G/B Offset: These functions are to set the single picture's R/G/B brightness.
Picture R/G/B Gain: These functions are to increase or decrease the color of single
picture's R/G/B.
Picture Contrast: This function is to set the single picture's color contrast.
Picture Brightness: This function is to set the single picutre's brightness.
Setup Language: There are two language available in the OSD and they are English
and Traditional Chinese.
Setup HDMI Sound: This function is to set the HDMI output audio sound to be O or OFF.
Setup Standard: Set it to O will allow system to set the setup menu into the default
value as indicated in the ( ).
Setup H/V Position Start: These functions are to set the total value of the vertical and
horizontal value of the TV wall.
Setup H/V Zoom Size: These functions are to set the total value of the vertical and
horizontal zoom in and zoom out size of the TV wall.
Setup H/V Blanking Edit: These functions are to set the total value of the vertical and
horizontal value of the blanking area of the TV wall.

Setup TV Option Width: This function is to set the numbers of the TV/ display that is to be
on a horizontal line of the TV wall.
Setup TV Option Height: This function is to set the numbers of the TV/display that is to be
on a vertical line of the TV wall.
Remote Control
1. PO ER*
Press this button to switch on the evice(s).
All the connecte Vi eo wall system control
evice(s) will be switch to ON.
2. PO ER OFF*
Press this button to switch off the evice. All
the connecte Vi eo wall system control
evice(s) will be switch to OFF.
3. SINGLE*
Press this button to set the image to be
isplaye on each an every connecte
TV/monitor i entically.
4. FULL*
There are 6 options of setting an image to be
isplaye on TV/ monitor an they are 2x2,
3x3, 4x4, 3x2, 4x3 an 5x5.
5. ▲▼◄►& OK
Press the arrow buttons to select an a just the
selection in the OSD menu an value or to
select the isplay. Press OK to confirm the
selection an all the isplays will be a juste
in once. If OK is not presse only the first
isplay will be a juste to the selecte value
6. RETURN
Press this button to return to the last layer of OSD selection or to exit the OSD.
7. MENU
Press this button to enter into the OSD menu. When the setting is selecte an confirme
all the output isplay will automatically change to the selecte settings.
8. HDMI/VGA/COMP/CV*
Press the hot key to select the input sources.
9. 720p/1080p@50/60*
Press the hot key to select 720p@50 Hz, 720p@60 Hz, 1080p@50 Hz an 1080p@60 Hz
timings for HDMI output, the SDI output timings will be automatically converte to
SMPTE 292M (1.485 Gbit/s) an SMPTE 424M/425M (2.970 Gbit/s)
10. U/OVER
Press this key to change the output image to be overscan or un erscan.
*Function that automatically a justs all monitors in once.

RS-232 Pin Assignments
RS-232 IN
PIN Assignment
1 NC
2 TxD
RS-232 OUT
PIN Assignment
1 NC
2 RxD
3 RxD 3 TxD
4 NC 4 NC
5 GND 5 GND
6 NC
7 Connect to pin 8
8 Connect to pin 7
9 NC
6 NC
7 Connect to pin 8
8 Connect to pin 7
9 NC
Baud Rate: 19200 bps
Data bit: 8-bit
Parity: None
Stop Bit: 1
Flow Control: None
RS-232 Commands
Commmand Action
0 23 0 53 0 30 0 30 0 31 0 23 POWER ON
0 23 0 53 0 30 0 30 0 30 0 23 POWER OFF
0 23 0 43 0 30 0 30 0 30 0 23 UNDER SCAN
0 23 0 43 0 30 0 30 0 31 0 23 OVER SCAN
0 23 0 43 0 52 0 WH 0 00 0 23 *Note
0 EF 0 05 0 D7 0 C0 0 22 0 0F 0 EE CHANGE TO HDMI
0 EF 0 05 0 D7 0 C0 0 22 0 0E 0 EE CHANGE TO PC
0 EF 0 05 0 D7 0 C0 0 22 0 02 0 EE CHANGE TO COMPOSITE
0 EF 0 05 0 D7 0 C0 0 22 0 0A 0 EE CHANGE TO COMPONENT
Note: WH are the TV Option’s Width and Height. W&H can be indicated fro 1~9 & A~F
where 11 eans single panel’s TV wall, 22 eans 2x2’s TV wall and so on up to FF is
15x15’s TV wall setting.

Specifications
SDI Transmission Rates 2.970 Gbps, 2.971/1.001 Gbps, 1.485 Gbps and
1.485/1.001 Gbps
Video andwidth 148 MHz
Input Ports 1 HDMI (Type A connector), 1 PC with Audio,
1 Component with R/L, 1 Composite with R/L
Output port 1 SDI (SD/HD/3G-SDI), 1 HDMI
SDI Cable Distance 3G/HD/SD up to 100/200/300 meters with BELDEN
1694A cable
HDMI Cable Distance Input: 10 m, 8/12-bit
Output: 10 m, 8/12-bit
Input HDMI Timing Support VGA@60/72/75, SVGA@56/60/72/75,
XGA@60/70/75, SXGA@60/75, UXGA@60,
WUXGA@60, WXGA@60, 480p@60, 576p@50,
720p@50/60, 1080i@50/60, 1080p@50/60
Input VGA Timing Support VGA@60/72/75, SVGA@56/60/72/75,
XGA@60/70/75, SXGA@60/75, UXGA@60,
WUXGA@60, WXGA@60, 1920 1080@60
Input Component Support 480i/p@60, 576i/p@50, 720p@50/60,
1080i/p@50/60
Input Composite Support NTSC, PAL
Output Timing Support HDMI: 720p@50/60, 1080p@50/60
SDI: SMPTE 292M (1.485 Gbit/s) & SMPTE
424M/425M (2.970 Gbit/s)
ESD Protection Human-bo y Mo el:
±8 kV (air-gap discharge)
±4kV (contact ischarge)
Dimensions 320 mm (W) 201mm (D) 49 mm (H)
Weight 1630 g
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0˚C~40˚C / 32˚F ~ 104˚F
Storage temperature -20˚C~60˚C / -4˚F ~ 140˚F
Relative Humidity 20~90% RH (no condensation)
Power Consumption W

Connection Diagram