Converters.TV HDMI 1.3 User manual

1x4 HDMI 1.3 with
Multi-channels Splitter - ID# 741
Operation Manual

Introduction
The 1x4 HDMI switch/selector allows one HDMI audio/video source such as
DVD/Blu-ray players or satellite boxes to send audio/video si nals to four HDMI
displays. This is compatible with HDMI v1.3 specifications, a cuttin -ed e
technolo y which defines the support to transfer Deep Color (12 bits/color)
and new lossless compressed (Dolby TrueHD, Dolby Di ital Plus and DTS-HD
Master Audio) di ital audio, with a hi h bandwidth up to 225MHz.
Application
 Connect one source equipment to HDMI input and four HDMI/DVI
displayers to HDMI output for Multi-display instantly.
 For Multi-levels displays, just connect extra splitter.
 Back up display ima e.
System
Requirements
HDMI input source equipment and output HDTVs.
Features
 HDMI 1.3, HDCP1.1 and DVI1.0 compliant.
 Deep color video up to 12bit, 1080p@(24/60)Hz.
 One HDMI source that can connect up to four HDMI displays
simultaneously.
 HDCP keysets allows each output to work independently when
connectin to a HDMI display.
 Splits a HDMI source up to four outputs without si nal loss.
 Supports DVI source and DVI display by usin HDMI to/from DVI adaptor
cable.
 Dolby Di ital Plus, DTS di ital audio transmission (32-192 kHz Fs sample
rate).
 Supports a wide ran e of PC and HDTV resolutions from VGA to UXGA
and 480i to 1080p.
 HDMI cable distance test with 1080p/8bits resolution the, Input/Output
can run up to 15/15 meters. If 1080p/12bits the Input/Output can run up to
10/15 meters.
 Selects EDID from TV mode or STD mode (this splitter).
 Supports CEC bypass.
 Supports System Reset function.

Operating Functions
and
Controls
Front Panel
① HDMI Outputs 1: Connect each of the output ports to the HDMI display.
When more than one output connected, the HDMI outputs play identical
video si nal simultaneously.
②HDMI Input: Connect input port to the HDMI or DVI output of your source
equipment such as DVD player or set-top-box.
③EDID Control switcher: Default factory settin is TV, leave as it is when the
displays are workin properly. Switch to STD to use built-in EDID, detail
capability in note.
④SYS. eset: Default factory settin is "OFF". Switch to "ON" the system will
send the internal CEC to the display within 8~10 minutes, to force all the
displays switch to HDMI port 1. In the sane time, TV must Supports CEC
function in order to display accordin ly. When switch to "OFF" the
system.
⑤Sync LED: The LED will illuminate when the HDMI source si nal is
connected to the input port.
⑥Power LED Indicator: The LED will illuminate when the power is connected.
⑦Power: Plu the 5V DC power supply into the splitter and connect the
adaptor to AC wall outlet.
Note:
1. When EDID is on TV: Leave as it is if display is properly, unit will detect
the first HDMI output source's EDID and record in the unit. If the first
detected output source is DVI it will pass to next source, until the first
HDMI been detected. The detection priority is HDMI v1.3>HDMI v1.2 >DVI.
2. When EDID is on STD: unit use built-in EDID
Video Supports -> 1080p 12 bit (max)
Audio Supports -> PCM2
3. Your EDID selection will only activated when the unit is replu and
power on.

Rear Panel
① HDMI Outputs 2/3/4: Connect each of the output ports to the HDMI
display. When more than one output connected, the HDMI outputs play
identical video si nal simultaneously.
Connection and
Installation
Specifications
Input Ports 4 x HDMI
Output Ports 2 x HDMI
Power Supply 5V/1A DC (US/EU st nd rds, CE/FCC/UL certified)
Dimensions (mm) 206(W) x 111(D) x 32(H)
Weight(g) 248
Ch ssis M teri l Pl stic
Silkscreen Color Bl ck
Oper ting Temper ture 0°C ~ 40°C