Converters.TV Ultimate XP User manual

PC VGA to TV Video Converter -
Ultimate XP ID# 519
Operation Manual

Introduction
PC VGA to TV Video Converter - Ultimate XP is a VGA to Video
converter allowing your PC images to be viewed on a standard TV screen,
or recorded using VCR's or V 's. The unit supports resolutions up to
UXGA (1600x1200) and can be output via Composite or S-Video and by
RGB (Scart) connections.
The PC VGA to TV Video Converter - Ultimate XP is ideal for
Professions like Advertising, Academic Lecturers, Retail Businesses or
just for Home use, the PC VGA to TV Video Converter - Ultimate XP has
simple and easy to use controls.
Features
•Plug and isplay design. No PC software drivers required.
•Power supplied from the PC's USB or PS/2 ports.
•Simultaneous display on PC VGA monitor and standard TV.
•Supports CV, SV or RGB (Scart) video outputs (switch selectable).
•Easy to use Panel Buttons: Menu (OS ), PAL/NTSC select, Power
on/off, Zoom in/out, Fine tune and Save.
•OS Menu allows control of: Freeze frame, Horizontal/ Vertical
Size, Brightness, Contrast, Hue, Saturation, Flicker, OS Color
and Reset.
•Full Remote Control supports above functions.
•Last Setting Save at switch Off/On.
•24 Bit, True Color igitizer.
PC Display Modes
& Resolutions
•VGA isplay Mode: 640x480, 800x600, 1024x768, 1280x1024,
1600x1200 (also 1152x864 & 1280x960).
•MAC isplay Mode (MAC G4, G4 Cubic, G3): 640x480,
832x624, 800x600, 1024x768, 1152x864.
•Apple isplay Mode (iMAC and iMAC V): 640x480, 800x600,
1024x768.

Operating Functions
and Controls
Front Panel
The following section shows the function of controlling the PC VGA to
TV Video Converter - Ultimate XP. Refer to Figure 1 for the Outline of
the PC VGA to TV Video Converter - Ultimate XP.
Fig. 1
Connectors
1. C IN : Plug with USB or PS/2 power cable.
2. VI EO OUT : Connects ULTIMATE XP to the VI EO input of
TV , VCR or Video projector.
. S-VI EO OUT : Connects ULTIMATE XP to your TV , VCR or
Video projector supporting the S-VI EO input.
4. RGB OUT (SCART) : Connects ULTIMATE XP to the RGB
input of TV - VCR or Video projector.
5. SCAN CNVTR : Connects Y Cable among PC, ULTIMATE XP
and monitor.
6. CVBS/RGB Switch: Slide to RGB side, only RGB OUT connector
has function, slide to CVBS side, only S-OUT and VIDEO OUT
connector can output signal.
Buttons
1. POWER : Toggle between power on & off.
2. SAVE : Press this button to save customer setting.
. PAL/NTSC : This button selects the video standard. Which
includes the following six video standards, "NTSC, NTSC-EIAJ,
PAL-M, PAL-N, PAL, PAL combination N". The refresh rate of

NTSC, NTSC-EIAJ and PAL-M is 60Hz. The refresh rate of PAL-
N, PAL and PAL combination N is 50Hz.
4. FINE TUNE : Press this to fine-tune the video image. (the same as
sharpness)
5. MENU : Press this button to cyclically activate the functions. The
functions are Freeze, Horizontal SIZE (H-SIZE), Vertical SIZE (V-
SIZE), Brightness, Contrast, Hue, Saturation, Flicker, OS color &
Reset.
6. ZOOM : Toggle between Zoom and Normal display.
7. UP, DOWN , LEFT, RIGHT : Press up, down, left & right button
to adjust the position of the TV display.
Remote
Controller
1. POWER : Toggle between power on &
off.
2. VIDEO STANDARD: Press this
button to select your video system. It
supports NTSC, NTSC-EIAJ, PAL-M,
PAL-N, PAL, PAL-COMBINATION-
N.
. MENU : Press this button to cyclically
activate the functions. These functions
are Fine Tune, H-SIZE, V-SIZE
Brightness, Contrast, Hue, Saturation,
Flicker, OS color & Save.
4. ZOOM : Toggle between Zoom and
Normal display.
5. RESET: Press this button will reset the
picture to factory setting.
6. FREEZE: Toggle between Freeze and
Normal display.
7. POSITION buttons: Press up, down,
left & right
▲▼◄►
Up own Left Right
button to adjust the position of the TV
display. These buttons also are used to
make adjustments to the setting in the
MENU

Installation for
IBM PC Users
The PC VGA to TV Video Converter - Ultimate XP is a "Plug and isplay"
video converter. The only thing required to get the image of computer
on TV is to make the proper connection. Please read the following
sections carefully for the installation of the hardware. Please refer to
Fig.2 for the installation for IBM PC Users.
Fig. 2

Step 1. Make sure your computer's (laptop, notebook or desktop PC)
power is turned OFF.
Step 2. Connect the Y Cable for IBM PC among computer's VGA
output, converter's VGA IN and VGA monitor. Please connect the
Y Cable mark "PC" to your computer's VGA output, connect the Y
Cable mark with "SCAN CNVTR" to ULTIMATE XP's VGA
IN and connect the Y Cable mark with "MONITOR" to VGA
monitor.
NOTE : Please connect the Y Cable carefully as above connecting
drawing otherwise it will cause you much inconvenience.
Step : With the supplied video cable, connect to the converter's VI EO
OUT to your TV or VCR video input.
Note : ULTIMATE XP also supports high quality S-OUT connector and
RGB OUT connector.
If your TV or VCR support S-Video IN or RGB VI EO IN, we highly
recommended you to use it to get the bets TV picture.
Step 4 : Connect one end of the supplied USB or PS/2 power cable to the
C IN port on the ULTIMATE XP and connect the other end to
your PC. Step 5 Power on your PC.
Step 6 : Power on the ULTIMATE XP.
Step 7 : Turn on your TV or VCR, and select the input from VI EO IN,
then you can get the picture on TV.

Specifications
•Video Type: NTSC/PAL.
•Video Outputs: Composite (RCA socket) & S-Video
(4pin mini-din socket), RGB (9pin mini-
din socket).
•PC/Monitor Connections: 15 pin -sub socket (Y cable)
•Power Supply: 5v C
•Power Source: PC USB or PS/2 port
•Size: 13cm(w), 8.3cm(d), 3.2(h)
•Weight: 0.128gms
Technical Tips
The following are problems that might arise when using the PC to TV
converter, and possible solutions of them.
Q: How can I enhance the display quality?
A: You can usually lower the TV contrast and sharpness control at the best
position, you can get a very good picture. To have the best effect, lower
the contrast control to minimize the flicker effect.
Q: I connect with a NOTEBOOK PC, no output is displayed on TV.
A: Check your computer hardware operating manual to enable the VGA
port or "OUTPUT". (Many Notebook computers have 3 settings, VGA
external only, VGA internal only, and VGA internal & external
simultaneously)
Q: Can I use multiple televisions to view the same image from my
computer?
A: Yes, you may connect one television to the next using a composite
video cable or an S-Video between the "VIDEO IN" and "VI EO
OUT" ports. We recommend using no more than six televisions
because of signal degradation.