Converters.TV 15372 User manual

HDBaseT HDMI UHD Receiver
and Scaler - # 15372
Operation Man al

Introd ction
The UHD Scaler is designed to extend and upscale HDMI signal on to two HDMI output
displays and one analog audio simultaneously. It supports 4Kx2K 3D 36-bit Deep Color
Hi-Def. lossless audio and other features defined by the latest HDMI specifications.
Allowing uncompressed video and audio as well as bi-directional IR control RS-232
pass through and LAN serving from a single CAT5e/6/7 cable over 100m of distance.
The management of source/sink scenarios can be operated easily through on-panel
buttons OSD IR remote control RS-232 and WebGUI control.
Applications
•Extending incoming signal through CAT5e/6/7 to HDMI outputs
•Scale up HDMI input low resolution video on High-Definition display
•Scale down HD signal down monitor
•Lecture room/showroom/Meeting room/Classroom display and control
•Public Commercial Display extension
Feat res
•HDMI with 3D supported and HDCP compliant
•Supports HDTV resolutions up to 4Kx2K (3840x2160@24/25/30 &
4096x2160@24)
•Supports scale down HD resolution on to monitor/display
•Supports data rate from 300Mbps to 3Gbps and Deep Color up to 1080p 36-bit
•Supports simultaneous HDMI outputs with different resolution setting
•Supports LPCM 2/5.1/7.1CH Dolby Digital 2~5.1CH DTS 2~5.1CH Dolby
TrueHD and DTS-HD Master Audio (Pass through)
•Extend HDMI IR RS-232 signal up to 100m through CAT5e/6/7 cable
•Supports Balanced audio and bi-directional IR control
•Supports Ethernet transmission rate up to 100Mbps
•Supports OSD on-panel, Remote, RS-232 and WebGUI control
Note: This system was tested with CAT6/23AWG cable, result may vary with cable of a
different specification
System
Req irements
HDBaseT compatible Transmitter input and PS3/Blu-ray player and output HDMI
TV/Display with connection cables.

Operation
Controls and Front Panel
F nctions
1. POWER & LED: Press this button to turn ON the device or set the device to standby
mode. The LED will illuminate in green when switch to ON. This device contains power
last memory and therefore when the power is connected the device will switch to
ON/Standby according to the last status.
2. IR Window: This IR Receiver receives the remote control signal from the packaged
included remote control only with IR frequency at 38kHz.
3. MENU: Press this button to enter into OSD menu.
4. ENTER: Press this button to select an OSD selection and press it again to confirm.
5. +/-: Press these buttons to move up/down in the OSD selection.
Rear Panel
1. HDMI OUT: Connect to HDMI TV/display or HD Amplifier for output
image and or audio display.
2 HDMI IN: Connect from source equipment such as Blu-ray/DVD/ PS3
players Set-Top-Box or any HDMI equipped source device for input signal
sending.
3 IR OUT: Connect to the supplied IR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the equipment to be
controlled.
4 IR IN: Connect the supplied IR Receiver cable for IR signal reception.
Ensure that remote being used is within the direct line-of-sight of the IR
Extender.

Note: Both IR IN and IR OUT signal are sending through CAT5e/6/7 cable
and therefore, it does not acce t the remote signal included in this ackage.
5 CAT5e/6/7: Connect to the Transmitter unit with a single CAT5e/6/7 cable
for receiving all data signals.
6 AUDIO OUT: Connect to active speaker or audio receiver for audio signal
output.
7 RS-232: This slot is to connect with D-Sub 9-pin cable from device
equipment for receiving RS-232 commands.
8 IP CONTROL: Connect from PC/Laptop with active internet service for
Telnet or WebGUI control with RJ-45 terminated cable.
9 FIRMWARE: This slot is reserved for firmware update use only.
10. DC 24V: Connect the adaptor with power cord included in the package
and connect to AC wall outlet for power supply.
Specifications
Frequency bandwidth 340Mbps to 10.2Gbps
Input ports 1 x HDMI 1 x CAT5e/6/7
1 x IR In 1 x USB (Service only)
1 x Control
Output ports 2 x HDMI 1 x IR Out
Resolution 480i~1080p@50/60 1080p@24 4K x 2K
HDMI I/O Cable Distance 15M@8/12bit 5M@4Kx2K
IR Frequency 30~50kHz
ESD Protection Human body model:
±8kV (air-gap discharge)
±4kV (contact discharge)
Power Supply 24V/ 3.75A DC (US/EU standards CE/
FCC/UL certified)
Dimensions 219mm (W) x 164.3mm (D) x 48mm (H)
Weight 450g
Chassis Material Metal
Silkscreen Color Black
Operating Temperature Operating from 0°C ~ 40°C
Storage Temperature -20˚C ~ 60˚C / -4 ˚F ~ 140 ˚F
Relative Humidity 20 ~ 90% RH (non-condensing)

DVI and HDMI S pported Resol tions Inp t O tp t
640x480@60 √ √
640x480@72 √ √
640x480@75 √ √
720x480@60 √ √
720x576p@50 √ √
800x600@60 √ √
800x600@72 √ √
800x600@75 √ √
1024x768@60 √ √
1024x768@70 √ √
1024x768@75 √ √
1280x720@50 √ √
1280x720@60 √ √
1280x768@60 √ √
1280x800@60 √ √
1280x1024@60 √ √
1360x768@60 √ √
1600x1200@60 √ √
1920x1080i@50 √ √
1920x1080i@60 √ √
1920x1080p@24 √ √
1920x1080p@25 √ √
1920x1080p@30 √ √
1920x1080p@50 √ √
1920x1080p@60 √ √
1920x1200@60(RB) √ √
3840x2160@24/25/30 √ √
4096x2160@24 √ √

Audio Sampling Rate Up to 192 kHz
HDMI inp t (Up to 192kHz) HDMI o tp t Analog o tp t
LPCM 2CH √ N/A
LPCM 5.1CH √ X
LPCM 7.1CH √ X
Dolby Digital 2~5.1CH/
DTS 2~5.1CH
√ N/A
Dolby TrueHD/
DTS-HD Master Audio
√ X
A dio Format LPCM 2/5.1/7.1CH Dolby Digital 2~5.1CH DTS 2~5.1CH (Pass
through) Dolby TrueHD and DTS-HD Master Audio
HDMI inp t HDMI o tp t Analog o tp t
LPCM 2CH √ √
LPCM 5.1CH √ X
LPCM 7.1CH √ X
Dolby Digital (Plus)
DTS-HD & DTS Surround
5.1CH
√ √
Dolby TrueHD/
DTS-HD Master Audio
√ X

Connection
Diagram