Converters.TV 858 User manual

Video to PC/HD Converter
ID# 858
Operation Manual

Introduction
This economical Video to PC converter box that can convert CV/SV (NTSC or PAL system)
to supported PC resolution li e XGA to UXGA or HD resolutions of 480p to 1080p. With
frame rate conversion feature that allows users to view DVD, VCR or Game sources on the
PC monitor, this device also has an On-Screen Display that allows users to easily select their
desired output resolution.
Application
 CV/SV signal display on VGA/PC monitor or TV
 STB/Camcorder signal display on PC monitor or TV
 DVD signal display on PC monitor or TV
System
equirements
Input source equipments such as DVD/Video cassette player and output PC/VGA
monitor component TV (output component TV needs D-Sub-15 to 3RCA cable
adaptor) display with connection cables.
Features
 Operates in NTSC 3.58MHz and PAL system
 Can scale CV/SV to PC or Component format
 Output resolution:
■ PC resolutions: XGA, SXGA, UXGA
■ Component resolutions: 480p/576p, 720p,1080p
 3D (frame based) motion adaptive YNR/CNR noise reduction
 On-Screen Display
 Advance 3D motion adaptive de-interlace
 Automatic 2:2 & 3:2 film mode detection
 50/60 Hz frame rate conversion ensures glitch-free display
 Play video games on your VGA monitors
 High-resolution output picture
 Plug & play- no drive software required
Operating Functions
and Controls
Left Side Panel
① S-Video input: This slot is where you connect the input source
equipment such as digital camcorder or PDAs with S-Video cable for
input signal sending.

②Composite (CV) input: This slot is where you connect the input
source
equipment such as personal media player or personal recorder with
R A cable for input signal sending.
③DC 5V In: This slot is where you plug the 5V D power supply into the
unit and connect the adaptor to an A wall outlet.
ight Side Panel
① Output resolution switch: This dip switch allows you to set
P / omposite
output Timing to PC resolution: XGA/SXGA/UXGA or
Component resolution: 480p/576p/720p/1080p. Simply push the dip
switch to left, middle or right and the output image will display your
desire timing. For P /
omposite timing selection please refer to Front Panel Section .
②PC OUT: This slot is where you connect the output display monitor
with
D-Sub 15pin cable for image display. When connecting to TV, using
D-Sub 15pin to 3R A adaptor is required.
Front Panel
① PC HD switch: This dip switch allows you to select P or component
HD timing output. Simply slide the dip switch to left or right and the output
mode will display your desire selection.
Top Panel
① CV SV SW & LED: Press this button to switch input source between
composite or S-Video. The Led will illuminate in yellow when switch to
composite input and red when switch to S-Video input.

OSD
1. Press the top panel’s button once to switch in between CV/SV. When input
source is disconnected the OSD will show “No Signal”.
2. Press the top panel’s button for 3 second to bring up OSD manual.
3. When the device is under PC mode the OSD will display input format and
output timing, source detection, PC monitor’s EDID and firmware version as to
above picture.
4. When the device is under HD mode the OSD will display input format and
output timing, frame rate conversion selection, video system and firmware version
as show in below picture.

Specifications
Input port 1 x V, 1 x SV
Output port 1 x VGA ( omponent out needs D-Sub 15
to 3R A adaptor)
Output Resolution P : XGA/SXGA/UXGA
omponent: 480p/576p/720p/1080p
Power Supply 5VD /1A (US/EU standards, E/F /UL certified)
ESD Protection Human body model: ± 8kV (air-gap discharge)±
4kV (contact discharge)
Dimensions (mm) 64(W) x 112.5(D) x 26(H)
Weight(g) 88
Chassis Material Plastic
Silkscreen Color Black
Operating Temp 0˚ ~40˚ / 32˚F ~ 104˚F
Storage temp -20˚ ~60˚ / -4˚F ~ 140˚F
Relative Humidity 20~90% RH (no condensation)
Power Consumption (W)2.5W(Max)
Support Timing
Chart