Savant HRX-SLN501 User manual

The Savant® HRX-SLN501 SmartLink receiver is HDBaseT™ 5Play™
compatible and receives audio and video, IR and RS-232 control,
Ethernet and Power from up to 328 ft (100 m) via a single Cat 5e/
6/7 cable. The start point can be a Savant HDBaseT transmitter,
SmartLink HDMI Matrix, or any device capable of transmitting
HDBaseT compliant signals.
Box Contents
(1) SmartLink HDBaseT™ Receiver (HRX-SLN501-00)
(1) Installation Kit (075-0156-xx):
(2) M3 x 4 mm Screws (039-0302-xx)
(1) Mounting Bracket (017-0872-xx)
(1) 4 in Cable Tie (014-0071-xx)
(1) 4-pin Screw Down Plug-in Connector (028-9395-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 90% Relative Humidity (non-
condensing)
Cooling
25 cubic feet per minute (CFM)
recommended.
Maximum BTU
7 BTU/hr
Dimensions and Weight
Dimensions and Weight
Height
0.94 in (2.39 cm)
Width
4.56 in (11.58 cm)
Depth
3.18 in (8.07 cm)
Weight
Shipping : 1.35 lb (0.61 kg)
Power
Power
PoH
Power over HDBaseT (PoH)
Power Supply
(Optional)
5V DC 2.5A
120-230V AC 50/60 Hz
Maximum Power
10 Watts
Compliance
Compliance
Safety and Emissions
FCC Part 15 | CE Mark | C-Tick
RoHS
Compliant
Enclosure
Enclosure
Metal enclosure with Savant’s Design Signature, black
Metal enclosure with Savant’s Design Signature, black
Minimum Supported Release
Minimum Supported Release
Savant OS
da Vinci 5.2.2
Front Panel
Ground Connector (Optional) - Used to connect
to a suitable ground reference when using
Power over HDBaseT (PoH).
Cable Lance
Use with included cable tie to secure power
supply connection.
5 VDC
5V DC 2.5A - Connect to optional power supply.
Not required when using PoH.
Link Status
LED
Green: Link with HDBaseT 5Play compatible
transmitter has been established.
Red: Power is present, but link to HDBaseT
5Play compatible transmitter has not been
established.
Off:HRX-SLN501 is not receiving power.
Link
8-pin RJ-45 female shielded
HDBaseT 5Play compatible - Connect to Link
connection on SmartLink HDBaseT Transmitter,
SmartLink HDMI Matrix, or 3rd party HDBaseT
5Play compatible transmitter.
Rear Panel
IR In/Out
4-Pin Screw Down Plug-in Connector
IR In: Receives IR Signals from a Savant or 3rd
party controller to send IR back to the start
point.
IR Out: Sends IR signals received from the start
point to control devices located near the
endpoint. Can be connected to an IR Flasher or
directly to a devices IR In.
See IR Wiring for important precautions
regarding IR functionality before making any
connections.
HDMI In
19-pin type A HDMI female
Supports HDMI and DVI (DVI/D Compatible)
DVI requires DVI to HDMI adapter (not included)
LAN
RJ-45 10/100 Base-T, auto-negotiating port with
Link/Activity LEDs.
Link LED
Off:Ethernet link is not established.
Green Solid: Ethernet link is established.
Green Blinking: Ethernet activity is occurring.
Data Rate LED
Off:10 Mbps data rate
Green: 100 Mbps data rate
RS232
Used to transmit and receive serial binary data
to and from serial controllable devices located at
the end point. 8-pin RJ-45 female
See RS-232 Wiring for pinouts.
HRX-SLN501-00 | 009-1025-04 | 150330
HRX-SLN501-00 | 009-1025-04 | 150330
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC
1
of
2
savant.com | 508.683.2500
SmartLink HDBaseT™ Receiver
Quick Reference Guide
For Product Info

Wiring and Connections
RS-232 Wiring
The RS-232 ports follow the Savant standard with pin 5 as RXD
(receive) and pin 6 as TXD (transmit). The diagram below shows
the wiring for the HRX-SLN501 side of the cable, the wiring on the
opposite side may vary based on the devices pin configuration.
RJ-45 to DB9 Adapters
Savant offers RJ-45 to DB9 adapters in a variety of configurations
that can be used for RS-232/422/485 control.
Refer to the RS-232 Conversion to DB9 and RS-422/485 Pinout
Application Note located on the Savant Community for more
information on RJ-45 to DB9 adapters.
IMPORTANT!
If you are using RJ-45 to DB9 adapters not supplied by Savant:
•Ensure that any wires required for communication/control are
terminated within the adapter.
•Ensure that all wires NOT required for communication/control
are NOT terminated in the connector.
•Ensure that the unused wires in the connector are cut to prevent
them shorting out, as they are still terminated in the RJ-45
connector on the controller side.
IR Wiring
IR connections are made using 4-pin Screw Down Plug-in
Connector supplied with receiver. The wire slips into the hole and
locks with the screw located at the top of the connector.
IMPORTANT! IR Wiring Precautions
•Ensure that all IR emitters are within 15 feet (4.6 meters) from
the controllers location.
•Use of 3rd party flashing IR emitters with Talk Back is not
recommended. These types of emitters can draw voltage away
from the IR signal that can degrade IR performance.
Additional Information
Refer to the following documents located on the Savant
Community for additional information.
•SmartLink Matrix Blueprint Deployment Guide
HRX-SLN501-00 | 009-1025-04 | 150330
HRX-SLN501-00 | 009-1025-04 | 150330
45 Perseverance Way, Hyannis, MA 02601
Copyright © 2015 Savant Systems, LLC
2
of
2
savant.com | 508.683.2500