Convision CC-5304 IR User manual

Manual CC 5304IR 1
Manual
CC-5304 IR
Date: January 2011 Convision Systems GmbH

Manual CC 5304IR 2
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than those specified.
Do NOT expose this appliance to rain or moisture.
This Installation should be made by a qualified service person and should confirm to all local codes.

Manual CC 5304IR 3
Warning
The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period, a fire may be caused.
Do not install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall and cause injury.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.

Manual CC 5304IR 4
Contents
NOTICE 5
Important Safeguard 5
Precautions 5
Features 6
Names and Functions of Parts 7
Dimensions 8
Installation 9
Cable Connections 10
Camera Operation 11
Menu 11
Settings 11
Lens (selection) 12
Shutter (condition and speed control) 13
White Balance 13
BACKLIGHT (Back Light Compensation) 14
AGC (Auto Gain Control) 15
DNR (Digital Noise Reduction) 15
SENS UP (Low illuminance) 16
Special 17
EXIT 21
Troubleshooting 22
Specification 23

Manual CC 5304IR 5
NOTICE
Important Safeguard
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments / Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they
may cause hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture.
5. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only
with a mounting device recommended by the manufacturer, or sold with the product. To insure proper
mounting, follow the manufacturer's instructions and use only mounting accessories recommended by
manufacturer.
6. Power source
This product should be operated only from the type of power source indicated on the marking label.
Precautions
■Operating
-Before using, make sure power supply and others are properly connected.
-While operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your local dealer.
■Handling
-Do not disassemble or tamper with parts inside the camera.
-Do not drop or subject the camera to shock and vibration as this can damage camera.
-Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
■Installation and Storage
-Do not install the camera in areas of extreme temperature, which exceed the allowable range.
-Avoid installing in humid or dusty places.
-Avoid installing in places where radiation is present.
-Avoid installing in places where there are strong magnetic fields and electric signals.
-Avoid installing in places where the camera would be subject to strong vibrations.
-Never expose the camera to rain and water.

Manual CC 5304IR 6
Features
Horizontal Resolution of 540 TV
Lines
Clear image quality has been achieved by
employing a SONY CCD with 410,000
(effective) pixels, which provides a
horizontal resolution of 540 TV lines.
Filter Changeable Day & Night
This camera has a function that
automatically selects the mode that is
appropriate for daytime or night-time
conditions. The COLOR mode operates in
daytime conditions to provide optimum
colors, and BW mode operates in night time
conditions to enhance the definition of the
image.
Photo Sensor & IR LED (18pcs)
IR LEDs are auto switching according to
the control of photo sensor.
Electronic IRIS
The electronic IRIS function enables
continuous automatic control of the
shutter between 1/60~1/120,000 seconds.
PRIVACY Function
The PRIVACY function conceals the
areas not required to appear on the image.
Controlled by OSD Menu
The camera functions are controlled by
selecting text displayed on the monitor
screen.
3 Axis built-in Vandal Resistant Dome
Housing
High Sensitivity
The built-in high sensitivity SONY COLOR CCD
enables a clear image even in 0.3Lux(0.1Lux
B/W) or as low as 0.002Lux with SENS-UP.
DNR (Digital Noise Reduction)
The amount of low illuminance noise
has been significantly reduced, and the
signal-to-noise ratio (S/N ratio) as well as
horizontal resolution have been improved,
resulting in clear and sharp images displayed
even in low light.
Additional Functions
SENS-UP, MOTION DETECTION,
MIRROR, SHARPNESS and SYNC
(INT/LL) functions are also available.
Weather Proof (IP 66)

Manual CC 5304IR 7
Names and Functions of Parts
1. Lens: Vari-Focal DC Auto Iris Lens
2. OSD PCB
●SET button: Used for the menu display. This button can be used to confirm settings after
changing the value of the selected function or current conditions.
●UP & DOWN buttons: Used for selecting items by moving the cursor up or down on the
menu screen.
●LEFT & RIGHT buttons: Used when changing item values, by moving the cursor to the
left or right on the menu screen.

Manual CC 5304IR 8
3. VBS-EXTRA for Connecting to LCD
Please use the supplied wire when connecting to LCD.
4. Photo Sensor & IR LED (18pcs)
IR LEDs are auto switching according to the control of photo sensor.
5. 3 Axis Bracket
Please loosen screws and fix tilted and panned position.
6. SMPS PCB for Dual Power
Dimensions

Manual CC 5304IR 9
Installation

Manual CC 5304IR 10
1. Dome Base Mounting
- Open the dome cover by loosening 3 screws using special wrench
provided.
- Mount the base of camera to a sturdy surface using 4 screws (1.5
inch) and 4 premade holes on the base of the dome.
2. Power Connect & Monitor Impedance
- AC24V Class 2 power supply.(AC24V/DC12V)
- To avoid fire or shock hazard, must use a UL listed power supply.
- Set the monitor impedance switch to 75W. Check the impedance
switch when the screen turns blurred.
3. Camera Module Adjustment
- Loosen screws for 3-axis camera bracket and adjust the direction
and angle of camera.
- Make sure to retighten the screws for camera bracket.
- Set any function you wish to activate by using the OSD buttons.
4. Dome Cover Mounting
- Replace the dome cover to the base and tighten 3 screws.
Cable Connections

Manual CC 5304IR 11
Camera Operation
Menu
Setup Menü
Lens (selection) Manual DC
Shutter (conditions and speed control) ESC Manual FLK
White Balance ATW AWC Manual
Backlight (Backlight Compensation) OFF LOW MIDDLE HIGH
AGC (Auto Gain Control) OFF LOW MIDDLE HIGH
DNR (Digital Noise Reduction) OFF LOW MIDDLE HIGH
Sens-Up (Low Illuminance) OFF Auto
Special Camera Titel Day/Night
SYNC Cam ID
Privacy Mirror
Digital Zoom Sharpness
Reset Return
Exit
Settings
Settings can be made using the 5 buttons located in the camera.
1. Press the SET button
Settings can now be made. The SETUP menu is displayed on the monitor.

Manual CC 5304IR 12
2. Auswählen der einzelnen Punkte mit Hilfe der UP and DOWN Tasten.
3. When the LEFT or RIGHT button is pressed, available values and modes are displayed in order.
Keep pressing the button until you get to the mode you wish to select.
4. Select 'EXIT' and then press the SET button to exit the set up Menu.
Notiz
• If appears at the mode you wish to operate, it means that there is a sub-menu which
can be selected by pressing the Set button.
• If appears at the mode item, it means that there is no mode available to be
selected.
Lens (selection)
This function is used to adjust the brightness of the screen.
1. When the SETUP menu is displayed on the screen, position the cursor to point to 'LENS'
by using the UP and DOWN buttons.
2. Select the type of the lens setting to use by pressing the LEFT or RIGHT button.
MANUAL: Manual Lens selection
DC: Auto Iris Lens selection

Manual CC 5304IR 13
3. Press the SET button if you which to return to the previous menu.
Shutter (condition and speed control)
Auto or manual control can be selected.
1. When the SETUP menu is on the screen, position the cursor to point to SHUTTER by
using the UP and DOWN buttons.
2. Select the shutter mode by pressing the LEFT or RIGHT button.
¾FLK: Select 'FLK' mode when flickering occurs on the screen
due to an imbalance between illumination and frequency.
NTSC Model:1/100, PAL Model: 1/120
NTSC Model:1/100, PAL Model: 1/120
¾ESC: Auto control of the shutter speed is enabled.
When ESC mode is on, the shutter speed is controlled automatically
according to the brightness of the scene.
¾MANUAL: The shutter speed can be controlled manually.
3. Select 'MANUAL' mode for manual shutter speed adjustment.
• Selectable speeds are from ‘1/60’ to ‘1/120,000’sec (NTSC) and ‘1/50’ to ‘1/120,000’sec (PAL).
4. Press the SET button when the settings are completed.
Notiz
• While using the internal synchronous system, if the shutter settings is on ESC and the camera is
directly facing bright fluorescent lights the image on the screen can be adversely affected-therefore
choose the installation location carefully.
• When MANUAL mode is on, the SENS UP function cannot be used.
White Balance
The screen colours can be adjusted using the WHITE BALANCE function.
1. Position the cursor to point to WHITE BAL on the menu by using the UP and DOWN
buttons.
2. Select the mode you wish to adjust by pressing the LEFT or RIGHT buttons.

Manual CC 5304IR 14
oATW(Auto Tracking White Balance):This mode can be used within the colour temperature range
1,800°K ~ 10,500°K (eg, fluorescent light, outdoor, sodium vapour lamp etc.)
oAWC(Auto White Balance Control): Press the SET button while the camera is directed at a piece
of white paper to obtain the optimum state under current illumination. If the environment, including the
light source, changes the white balance will need to be adjusted again.
oMANUAL: The manual adjustment mode enables finer adjustment. Select ATW or AWC first then
change to manual adjustment mode and press the SET button. Set the appropriate colour
temperature then increase / decrease the red and blue colour values and monitor the colour changes
of the object.
Note
• Under the following conditions the WHITE BALANCE function may not operate properly. In such
cases, please select the AWC mode.
1. When the objects surroundings have a very high colour temperature (eg, a clear sky and sunset)
2. When the objects surroundings are dark.
3. If the camera directly faces a fluorescent light or is installed in a place where there are considerable
changes in illumination, the WHITE BALANCE function my become unstable.
BACKLIGHT (Back Light Compensation)
When there is a strong backlight behind the object, clear images of the
background as well as the object can still be obtained by using the
BACKLIGHT function.
1. Position the cursor to point to 'BACKLIGHT' on the SETUP menu by using
the UP and DOWN buttons.
2. Select the value required by pressing the LEFT or RIGHT button.
¾HIGH: The gain increases from 0dB up to 42dB.
¾MIDDLE: The gain increases from 0dB up to 30dB.
¾LOW: The gain increases from 0dB up to 18dB.
¾OFF: BACKLIGHT function does not operate.

Manual CC 5304IR 15
AGC (Auto Gain Control)
1. Position the cursor to point to 'AGC' on the SETUP menu by using the
UP and DOWN buttons.
2. Select the value required by pressing the LEFT or RIGHT button. As the
level of gain increases the screen gets brighter but the level of noise will
also increase.
¾HIGH : The gain varies between the range of 6dB ~ 42dB.
¾MIDDLE : The gain varies between the range of 6dB ~ 30dB.
¾LOW : The gain varies between the range of 6dB ~ 18dB.
¾OFF : The gain is fixed at 6dB.
DNR (Digital Noise Reduction)
The level of background noise in low light decreases automatically as the
level of gain changes.
1. Position the cursor to point to 'DNR' on the SETUP menu by using the
UP and DOWN buttons.
2. Select the value required by pressing the LEFT or RIGHT button.

Manual CC 5304IR 16
¾OFF : There is no reduction in noise level.
¾LOW : There is a small reduction in noise level with almost no
ghost image.
¾MIDDLE : The most effective mode. There is a sufficient reduction in
noise levels without causing significant ghosting.
¾HIGH : The level of noise is reduced greatly, however there is an
increase in ghosting.
Notiz
When AGC is turned off, DNR does not operate.
SENS UP (Low illuminance)
SENS UP helps maintain a bright, clear screen image by automatically
detecting changes in the level of light in low light level conditions.
1. Position the arrow to point to 'SENS UP' on the SETUP menu by using the
UP and DOWN buttons.
2. Select the value required by pressing the LEFT or RIGHT button.
AUTO: Low light level automatic mode.
OFF : The function does not operate.
Notiz
•When SHUTTER is in the manual or flk mode, SENS UP does not operate.
•When AGC is turnes off, SENS UP does not operate.
3. Press the SET button when all the settings are complete.

Manual CC 5304IR 17
Notiz
• The maximum storage magnification in low light level movement situations can be adjusted
by pressing the SET button in AUTO mode. (X2~X128)
• As the magnification increase the screen gets brighter; however the after image also
increasees.
• If storage magnification is increased while SENS UP is operational, it may cause noise and
spots may appear; this is normal.
Special
1. Position the cursor to point to 'SPECIAL' on the SETUP menu by using the
UP and DOWN buttons.
2. Select the mode required by pressing the UP or DOWN button.
CAMERA ID: If an ID is input, this camera ID appears on the monitor
and recorded footage.
1) Position the cursor to point to ‘CAMERA ID’ by using the
UP or DOWN button.
2) Select 'ON' by pressing the LEFT or RIGHT button.
Notiz
• If OFF is selected, the ID does not appear on the monitor even
If it has been input.
3) Press the SET button.

Manual CC 5304IR 18
4) Up to 15 characters can be used for the camera ID.
•Move the cursor to the letter required by using the UP and DOWN button.
•Select an ID from A, B~Y, Z, a, b ~ y, z, 0,1~8,9 by using the UP, DOWN, LEFT and RIGHT buttons.
•Lock in the characters by using the SET button. Once locked in the cursor moves to the next space in
the ID.
•Repeat the above steps until the ID is complete.
Note
Press the SET button after moving the cursor to CLR and all the letters will be
erased. If you want to correct a letter move the cursor to the arrow at the bottom
left of the screen and press 'SET'.
Position the cursor above the letter you wish to correct and then move the cursor
onto the letter you wish to choose and press the SET button.
5) When the camera ID is complete, select a position for the name to be
displayed.
•Move the cursor onto 'POS' and then press the SET button.
•The ID appears in the top left corner.
•Select the position where the ID is to be displayed
by using the 4 directional buttons, and then press
the SET button.
6) Select 'END' and press the SET button to complete ID input.

Manual CC 5304IR 19
COLOR
AUTO: This camera has an IR Cut Filter and automatically changes to the appropriate mode
dependant on lighting levels. COLOR mode is selected during daylight and
B/W mode at night time.
Note
•When the AGC is turned off, COLOR does not operate.
•When an infrared light is used, there may be a problem with focusing.
SYNC: Two sychronisation modes are available, INTERNAL and EXTERNAL LINE-LOCK. In
LINE-LOCK mode, it synchronises the video signal between cameras without a synchronous
generator. The line-lock synchronisation is only used in areas of 60Hz (NTSC Models) / 50Hz
(PAL Models).
- INT: Internal synchronisation
- LL: External Line-Lock synchronisation
• If ‘LL’ is selected, it can be adjusted to the desired phase. Press the SET button.
• Adjust to the desired phase from 0 to 359.
Note
• When the mains frequency is 50Hz, the line-lock mode (NTSC Models) cannot be used.
• When the mains frequency is 60Hz, the line-lock mode (PAL Models) cannot be used.

Manual CC 5304IR 20
MOTION DETECTION:
This product has a feature that allows you to observe movements of objects in 4 different areas on the
screen, and the words 'MOTION DETECTED' appear on the screen when movement is detected; hence
a single individual can conduct supervision efficiently. The camera detects an object's movement by
sensing disparity of outline, and level of brightness and colour.
• Please press the SET button.
- OFF: MOTION DETECTION mode is cancelled.
- ON: Any motion in the selected areas is observed.
• Please select the area you wish to observe from the 4 areas in AREA
SEL mode.
• Please select ON mode for the chosen area.
• Please adjust the size of the area to be observed by using the UP,
DOWN, LEFT or RIGHT button.
Please press the SET button to save the changes and complete the settings.
PRIVACY:
This mode conceals the areas you do not wish to appear on the screen.
- OFF: Cancels the PRIVACY mode.
- ON: Operates the PRIVACY mode.
• Please press the SET button.
• Please select the area you do not wish to appear from the 4 areas in
AREA SEL mode.
• Please select ON mode for the chosen area.
• Please adjust the size of the area to be concealed by using the UP, DOWN,
LEFT or RIGHT button.
MIRROR
ON: Sets a horizontal image inversion.
OFF: Cancels the inversion.