Cooper Lighting Stealth Graze Fixture Mounting V90181 User manual

Vertical Wall
(Grazed Surface)
Ceiling
Blocking
FIGURE 1
2. The Trim of the Stealth Graze must now be removed so that
access can be ained to the Thermal Protector. This step may
be skipped if blockin is not in the way of the Thermal
Protector or a different mountin method is bein used. Place
the Utility Wed e between the Trim and the Plaster Frame and
push strai ht up until the Trim pops out. (Fi ure 2) Do not
bend the Utility Wed e while in the Fixture, as it mi ht break.
Utility Wedge
Trim
Plaster Frame
T ermal Protector
FIGURE 2
3. Once the Trim is removed, the Thermal Protector should be
pulled inside the Housin so that the Fixture will slide past
the Blockin . To do this, reach inside the Housin , unscrew
the Thumb Screw, and pull the Thermal Bracket (with the
Thermal Protector attached) into the Housin . (Fi ure 3)
The Fixture can now be hoisted into the ceilin for mountin .
Housing
FIGURE 3
T umb Screw
T ermal
Bracket
T ermal
Protector
4a.If two or more Stealth Graze Housin s are bein used, ali n
Housin s into Ceilin , buttin fixtures end to end ti htly. Place
two (2) Connectin Screws throu h Connectin Holes on
Housin s, and secure with Connectin Nuts. (Fi ure 4)
4b.Once the Fixture is placed into the ceilin , it can be secured
usin countersunk screws. Fixture should be mounted by
screwin throu h the Plaster Frame (screw holes are already
countersunk) and into the blockin . (Fi ures 5 & 6) If additional
screw locations are needed, there is a screw line in the Plaster
Frame extrusion to facilitate this process.
Connecting Screws
Connecting Nuts
Connecting
Holes
Housing A
Housing B
FIGURE 4
FIXTURE MOUNTING
1. Before Stealth Graze can be installed, blockin should be
installed above ceilin around the fixture. (Fi ure 1)
V90181
STEALTH GRAZE
FIXTURE MOUNTING
FIXTURE MOUNTING
1. Before Stealth Graze can be installed, blockin should be
installed above ceilin around the fixture. (Fi ure 1)
V90181
STEALTH GRAZE
FIXTURE MOUNTING
7945 Orion Avenue, Van Nuys, CA 91406 818-349-3030/ 800-356-3030 FAX [phone]
Visit our web site at: www.rsalighting.com
C
Avoid Fire or Electric Shock
L
US
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local re ulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
U
INSTALLATION INSTRUCTIONS
RSA Lighting
R

FIGURE 6
Mudding Material
Thermal Protector
Housing
Ceiling
Blocking
Mounting Screws
STEALTH GRAZE
FIXTURE MOUNTING
Thumb Screw
6. The Fixture can now e mudded with the ceiling material. Apply
drywall tape to inside of the fixture to ensure fixture is not mudded.
Place mudding compound on edge of Plaster Frame and feather
away from fixture on all three sides. (Figure 6) Once the ceiling is
dry, the Trim can now e inserted into the Housing.
Trim
Blocking
Mounting Screw
Plaster Frame
Ceiling
FIGURE 5
V90181
5. Once the fixture is mounted, the Thermal Protector can e returned
to proper position y placing the Thermal Bracket ack into the
Housing using the Thum Screw. (Figure 6)
FIXTURE MOUNTING (Cont'd)
V90181
5. Once the fixture is mounted, the Thermal Protector can e returned
to proper position y placing the Thermal Bracket ack into the
Housing using the Thum Screw. (Figure 6)
FIXTURE MOUNTING (Cont'd)
7945 Orion Avenue, Van Nuys, CA 91406 818-349-3030/ 800-356-3030 FAX [phone]
Visit our web site at: www.rsalighting.com
C
Avoid Fire or Electric Shock
L
US
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely efore installation.
*Failure to follow Installation Instructions may void warranties.
U
INSTALLATION INSTRUCTIONS
RSA Lighting
R