Cornelius Flavor Fusion 620053922 User manual

Icemaker & Adaptor Hold-Down Kit Installation Instructions
© 2008, IMI Cornelius Inc. - 1 - Publication Number: 629096853INS
INSTALLATION INSTRUCTIONS
ICEMAKER AND ADAPTER HOLD-DOWN KIT P/N 629096853
FOR FLAVOR FUSION / IDC UNITS ONLY
Instructions for Non-30 Inch Wide Icemaker – Flavor Fusion Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Instructions for 30 Inch Wide Icemakers – Flavor Fusion Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Instructions for Non-30 Inch Wide Icemaker – IDC Series Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Instructions for 30 Inch Wide Icemaker – IDC Series Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Parts Included in the Kit are Shown in Table 1:
Tools Needed:
• Power Drill
• 9/64 in. (.140 in.) Drill Bit
• #2 Phillips Head Screwdriver
INSTRUCTIONS FOR NON-30 INCH WIDE ICEMAKER – FLAVOR FUSION UNITS
WARNING: Failure to follow the installation instructions correctly may result in equipment damage
and/or personal injury.
The Parts shown in Table 2 are NOT Used for this Installation:
1. Remove the two top black side panel screws from both sides of the Flavor Fusion unit (See Figure 1) and
save the screws.
Table 1
Part No. Description Qty.
22127 Icemaker Rear Mounting Plate 2
50904 Silicone sealant 1 tube
620053922 Left Side Adapter Hold-Down Bracket 1
620053923 Right Side Adapter Hold-Down Bracket 1
620518916 Adaptor/Icemaker Side Hold-Down Plate (Flat) 2
620701601 #10-16 S.S. Sheetmetal Screws 12
Table 2
Part No. Description Qty.
620518916 Adaptor/Icemaker Side Hold-Down Plate (Flat) 2
Release Date: June 30, 2008 www.cornelius.com Revision: 1

Icemaker & Adaptor Hold-Down Kit Installation Instructions
Publication Number: 629096853INS - 2 - © 2008, IMI Cornelius Inc.
Figure 1
2. Locate the two right and left side hold down brackets, shown in Figure 2. These are the brackets with the
bent flange on them.
Figure 2
3. There are two options for installing the brackets, outside of the side panels or behind the side panels, as
shown in Figure 3. Left side of unit is shown in Figure 3.
Figure 3
4. Place the bracket over the adapter lid then re-install the black screws that were removed in Step 1.
Side Panel
Screws
Left Side
Right Side
Straight Edge Goes
to the Rear of the
Dispenser

Icemaker & Adaptor Hold-Down Kit Installation Instructions
© 2008, IMI Cornelius Inc. - 3 - Publication Number: 629096853INS
Figure 4
5. Repeat Steps 1 through 4 for the opposite side of the dispenser.
6. Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 5.
Figure 5
7. Locate the icemaker mounting plates at the rear of the icemaker and position as shown in Figure 6, if plates
are not already installed.
NOTE: Kit contains two plates, both mounting plates must be installed.
Figure 6
8. Using the plate as a template, drill 9/64 in. (0.140 in.) holes into the icemaker base and the dispenser, as
shown in Figure 7.
Flange on bracket
MUST Go Over the
Top of the Adapter
Lid as Shown.
Run a Continuous
Bead of Caulking
Around the Adapter
Top

Icemaker & Adaptor Hold-Down Kit Installation Instructions
Publication Number: 629096853INS - 4 - © 2008, IMI Cornelius Inc.
CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser
wrapper as damage may occur to unseen parts.
Figure 7
9. Install the second mounting plate on the other side of the icemaker base. Using supplied sheetmetal
screws, screw four (4) screws per plate into the icemaker base and dispenser wrapper.
INSTRUCTIONS FOR 30 INCH WIDE ICEMAKERS – FLAVOR FUSION UNITS
CAUTION: Failure to follow the installation instructions correctly may result in equipment damage
and/or personal injury.
The Parts shown in Table 3 are NOT Used for this Installation:
1. Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 8.
Figure 8
2. Remove the two top black side panel screws from both sides of the Flavor Fusion unit (See Figure 1) and
save the screws.
Table 3
Part No. Description Qty.
22127 Icemaker Rear Mounting Plate 2
620053922 Left Side Adapter Hold-Down Bracket 1
620053923 Right Side Adapter Hold-Down Bracket 1

Icemaker & Adaptor Hold-Down Kit Installation Instructions
© 2008, IMI Cornelius Inc. - 5 - Publication Number: 629096853INS
3. Locate the two flat, hold down brackets, shown in Figure 9.
Figure 9
4. There are two options for installing the brackets, outside of the side panels or behind the side panels, as
shown in Figure 10. Right side of unit is shown in Figure 10.
Figure 10
5. Place bracket as shown then re-install the black screws as shown in Figure 11, that were removed in Step 1.
Figure 11
6. Using the plate as a template, drill 9/64in. (0.140 in.) holes in the icemaker base, as shown in Figure 12.
CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser
wrapper as damage may occur to unseen parts.
Insert Screws

Icemaker & Adaptor Hold-Down Kit Installation Instructions
Publication Number: 629096853INS - 6 - © 2008, IMI Cornelius Inc.
Figure 12
7. Using the supplied sheetmetal screws, screw four (4) screws per plate into the dispenser wrapper and
icemaker base.
8. Repeat Steps 2 through 7 on the other side of the dispenser.
INSTRUCTIONS FOR NON-30 INCH WIDE ICEMAKER – IDC SERIES UNITS
WARNING: Failure to follow the installation instructions correctly may result in equipment damage
and/or personal injury.
The Parts shown in Table 4 are NOT Used for this Installation:
1. Locate the two right and left side hold down brackets, shown in Figure 2. These are the brackets with the
bent flange on them.
2. Position bracket with the straight edge towards the rear of the unit, as shown in Figure 13. Also, the flange
of the bracket must be over the adapter lid, as shown in Figure 4.
Figure 13
3. Using the bracket as a template, drill two 9/64 in. (0.140 in.) holes in the dispenser wrapper.
CAUTION: Be careful not to drill too deep and/or too fast into the dispenser wrapper as damage may
occur to unseen parts.
Table 4
Part No. Description Qty.
620518916 Adaptor/Icemaker Side Hold-Down Plate (Flat) 2
Straight Edge of
Bracket Goes to
the Rear of the
Dispenser

Icemaker & Adaptor Hold-Down Kit Installation Instructions
© 2008, IMI Cornelius Inc. - 7 - Publication Number: 629096853INS
4. Using supplied sheetmetal screws, screw two (2) screws per bracket into the dispenser wrapper, as shown
in Figure 14.
Figure 14
5. Repeat Steps 1 through 4 for the opposite side of the dispenser.
6. Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 5.
7. Locate the icemaker mounting plates at the rear of the icemaker and position as shown in Figure 6, if plates
are not already installed.
NOTE: Kit contains two plates, both mounting plates must be installed.
8. Using the plate as a template, drill 9/64 in. (0.140 in.) holes into the icemaker base and the dispenser, as
shown in Figure 7.
CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser
wrapper as damage may occur to unseen parts.
9. Using the supplied sheetmetal screws, screw four (4) screws per plate into the dispenser wrapper and
icemaker base.
10. Repeat Steps 7 through 9 on the other side of the dispenser.
INSTRUCTIONS FOR 30 INCH WIDE ICEMAKER – IDC SERIES UNITS
WARNING: Failure to follow the installation instructions correctly may result in equipment damage
and/or personal injury.
The Parts shown in Table 5 are NOT Used for this Installation:
1. Using the supplied silicone tube, seal icemaker all around to the adapter top, as shown in Figure 15.
Table 5
Part No. Description Qty.
22127 Icemaker Rear Mounting Plate 2
620053922 Left Side Adapter Hold-Down Bracket 1
620053923 Right Side Adapter Hold-Down Bracket 1

Icemaker & Adaptor Hold-Down Kit Installation Instructions
Publication Number: 629096853INS - 8 - © 2008, IMI Cornelius Inc.
Figure 15
2. Locate the two flat hold down brackets, shown in Figure 9.
3. Position the plate as shown in Figure 16, with the straight edge towards the rear of the unit and the top of
the plate is about ¾ in. above the adapter lid.
Figure 16
4. Using the plate as a template, drill 9/64 in. (0.140 in.) holes into the icemaker base and the dispenser, as
shown in Figure 17.
CAUTION: Be careful not to drill too deep and/or too fast into the icemaker base and dispenser
wrapper as damage may occur to unseen parts.
Figure 17
3/4 in.

Icemaker & Adaptor Hold-Down Kit Installation Instructions
© 2008, IMI Cornelius Inc. - 9 - Publication Number: 629096853INS
5. Using the supplied sheetmetal screws, screw four (4) screws per plate into the dispenser wrapper and
icemaker base.
6. Repeat Steps 1 through 5 on the other side of the dispenser.