CORNING LSE User manual

Corning®LSE™
Low Speed Orbital
Shaker
Instruction Manual
Catalog Numbers:
6780
6781
6782

Table of Contents
1.0 General Specifications .......................................................... 1
2.0 Safety Precautions.............................................................. 1
3.0 Installation of the Orbital Shaker................................................2
3.1 Unpacking ..................................................................2
3.2 Selecting the Location .......................................................2
3.3 Attaching the Power Cord ...................................................2
4.0 Operating Instructions..........................................................3
4.1 Controls ....................................................................3
4.2 Basic Operation .............................................................3
5.0 Troubleshooting Guide .........................................................3
6.0 Maintenance and Cleaning .....................................................4
7.0 Limited Warranty...............................................................4
8.0 Equipment Disposal ............................................................5

1
Instruction Manual
1.0 General Specications
Electrical Requirements
120V model
230V model
120V ± 10%, 50/60Hz, 0.3A
230V ± 10%, 50/60Hz, 0.15A
Fuse 2 x 1A
Speed 3 to 60 rpm
Shaker Orbit 0.75 in. (1.9 cm)
Timer 20 to 120 minutes in 10 minute step, HOLD function
Maximum Load 5 kg
Dimensions 11.6 x 13.4 x 6.3 in. (29.5 x 34 x 16 cm)
Platform Dimensions 11.6 x 11.6 in. (29.5 x 29.5 cm) useable area
Weight 14.5 lbs. (6.6 kg)
Operating Conditions 4°C to 65°C, up to 85% RH, non-condensing
Warranty 5 years
Platform Size 11.8 x 11.8 in. (30 x 30 cm)
This device is intended for use in a basic electromagnetic environment (Basic, class B), and it
is in compliance with IEC 61326-1. Supply cord can be exchanged only with cord 3 x 1.0 mm2or
for USA/Canada 3 x 18 AWG.
The Corning® LSE™ Low Speed Orbital Shaker is designed to be safe when operated under the
following conditions:
Indoor use
Altitude up to 2,000 meters
Pollution Degree 2
2.0 Safety Precautions
Do not use the shaker near water. Ensure that water does not get on the device,
particularly during cleaning.
If the unit is used in a manner not specified in this manual, then the unit may
become unsafe to operate and may void the warranty.
This product must be connected to a grounded power outlet for safe functioning.
Use only the power cord supplied with the product.
The equipment will not restart if the main power source is interrupted.
The equipment will restart in cases of mechanical interruption.
Do not expose the shaker to aggressive vapors (e.g., organic solvents).
Do not insert any objects into the shaker (such as a screwdriver or metal rods).
Never operate the shaker without the platform securely attached.
Hazardous samples should be shaken only in appropriate containment vessels.

2CORNING LSE LOW SPEED ORBITAL SHAKER
Do not shake flammable or explosive samples.
The electrical warning symbol indicates the presence of a potential hazard which
could result in electrical shock.
Do not put your fingers between the shaking platform and the housing. Danger of
mechanical injury.
3.0 Installation of the Orbital Shaker
3.1 Unpacking
Before starting the installation, carefully examine the shaker for possible damage or missing parts.
Open the box and carefully remove the padding. Check that the shaker has not been visibly
damaged during transportation. Keep the packing material until you ensure that the shaker
works properly.
Carefully lift the device out of the box.
Be sure that the following information is included on the serial label located on the back of
the unit: serial number, catalog number, electrical rating.
Check that the power cord plug has a pin configuration that matches a wall socket
according to the local standard.
Should any kind of damage have occurred during transportation, contact the carrier
immediately. The carrier is responsible for shipping damage.
3.2 Selecting the Location
Put the shaker on a horizontal, leveled, and stable surface.
Leave enough space around the shaker for normal air circulation (6 in./15 cm minimum).
Leave enough space around the shaker for easy access and maintenance.
Avoid locations subject to shocks and vibrations.
Avoid locations subject to frequent power fluctuations or power losses, as this may affect
shaker performance.
Select a location that is dry and not subject to drafts or moving air from heating or air conditioning
vents or air blown by other equipment. Plug the unit into a properly grounded outlet.
3.3 Attaching the Power Cord
Connect the main power cord to the shaker and then connect the plug end of the cord to a
grounded wall socket. Avoid lines to which powerful electric motors, refrigerators, and similar
devices are connected.
Be careful when you plug the cord to a grounded wall socket. Do not touch the
plug with wet hands. Do not pull the plug by the cord.

3
Instruction Manual
4.0 Operating Instructions
4.1 Controls
23
6
4
5
1
1. POWER switch: Turns the shaker ON (power switch illuminates) or OFF
2. SPEED knob: Sets the shaker speed
3. TIME knob: Sets the time of the shaker
4. HOLD yellow light: Illuminates when the shaker is set for continuous running
5. START/STOP button: START or STOP shaking
6. RUN green light: Illuminates when the shaker is running
4.2 Basic Operation
Switch on POWER.
Set SPEED knob on desired value.
Set TIME knob on desired value or on HOLD – continuous function (yellow light next to
HOLD will illuminate).
Press START/STOP button to start shaking.
Press START/STOP button to stop shaking (HOLD position). Device automatically stops after
the set time passes. NOTE: Pressing the START/STOP button during operation will reset the
timer.
5.0 Troubleshooting Guide
Be sure to disconnect the shaker from the main power source immediately in case of any
signs of malfunction and contact Corning Customer Service at 800.492.1110 or 978.442.2200.
Problem Solution
Power switch does not light up Check the power connection. Check the fuses.
Contact Corning Customer Service.
Shaker does not start Check the power connection. Check the fuses.
Contact Corning Customer Service.

4CORNING LSE LOW SPEED ORBITAL SHAKER
6.0 Maintenance and Cleaning
No routine maintenance or lubrication is required.
It is recommended that the shaker be kept clean to ensure a long, trouble-free operation.
The outside housing of the platform shaker may be cleaned with a soft, damp cloth when
needed. Do not use any aggressive or abrasive cleaners (acetone, nitro, polish, etc.), as they
may permanently damage the shaker finish.
Before cleaning the shaker, always unplug the power cord from the wall socket.
Make sure the shaker is switched off before installing an additional platform.
7.0 Limited Warranty
Corning Incorporated (Corning) warrants that this product will be free from defects in
material and workmanship for a period of two (2) years from date of purchase. CORNING
DISCLAIMS ALL OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE.
Corning’s sole obligation shall be to repair or replace, at its option, any product or part thereof
that proves defective in material or workmanship within the warranty period, provided the
purchaser notifies Corning of any such defect. Corning is not liable for any incidental or
consequential damages, commercial loss, or any other damages from the use of this product.
This warranty is valid only if the product is used for its intended purpose and within the
guidelines specified in the supplied instruction manual. This warranty does not cover damage
caused by accident, neglect, misuse, improper service, natural forces, or other causes not
arising from defects in original material or workmanship. This warranty does not cover motor
brushes, fuses, light bulbs, batteries, or damage to paint or finish. Claims for transit damage
should be filed with the transportation carrier.
In the event this product fails within the specified period of time because of a defect in
material or workmanship, contact Corning’s Customer Service at 800.492.1110. Outside the
United States, call +1.978.442.2200 or contact your local Corning sales office.
Corning Customer Service will help arrange local service where available or coordinate a return
authorization number and shipping instructions. Products received without proper authorization
will be returned. All items returned for service should be sent postage prepaid in the original
packaging or other suitable carton, padded to avoid damage. Corning will not be responsible for
damage incurred by improper packaging. Corning may elect for onsite service for larger equipment.
Some states do not allow limitation on the length of implied warranties or the exclusion
or limitation of incidental or consequential damages. This warranty gives you specific legal
rights. You may have other rights which vary from state to state.
No individual may accept for, or on behalf of Corning, any other obligation of liability, or
extend the period of this warranty.

5
Instruction Manual
For your reference, make a note of the serial and model number, date of purchase, and supplier here.
Model No. ____________________________________ Serial No. __________________________________
Date Purchased ________________________________ Supplier ___________________________________
8.0 Equipment Disposal
According to Directive 2012/19/EU of the European Parliament and Council of 4th
July 2012 on waste and electronic equipment (WEEE) as amended, the Corning®
LSE™ Low Speed Orbital Shaker is marked with the crossed-out wheeled bin and
must not be disposed of with domestic waste.
Consequently, the buyer shall follow the instructions for reuse and recycling of
waste electronic and electrical equipment (WEEE) provided with the products and
available at www.corning.com/weee.

Warranty/Disclaimer: Unless otherwise specied, all products are for research use or general
laboratory use only.* Not intended for use in diagnostic or therapeutic procedures. Not for use in
humans. These products are not intended to mitigate the presence of microorganisms on surfaces
or in the environment, where such organisms can be deleterious to humans or the environment.
Corning Life Sciences makes no claims regarding the performance of these products for clinical or
diagnostic applications. *For a listing of US medical devices, regulatory classications or specic
information on claims, visit www.corning.com/resources.
Corning’s products are not specically designed and tested for diagnostic testing. Many Corning
products, though not specic for diagnostic testing, can be used in the workow and preparation
of the test at the customers discretion. Customers may use these products to support their claims.
We cannot make any claims or statements that our products are approved for diagnostic testing
either directly or indirectly. The customer is responsible for any testing, validation, and/or regulatory
submissions that may be required to support the safety and ecacy of their intended application.
For a listing of trademarks, visit www.corning.com/clstrademarks. All other trademarks are the property of their respective owners.
© 2022 Corning Incorporated. All rights reserved. 5/22 CLS-AN-694DOC REV1
Corning Incorporated
Life Sciences
www.corning.com/lifesciences
NORTH AMERICA
t 800.492.1110
t 978.442.2200
ASIA/PACIFIC
Australia/New Zealand
t 61 427286832
Chinese Mainland
t 86 21 3338 4338
India
t 91 124 4604000
Japan
t 81 3-3586 1996
Korea
t 82 2-796-9500
Singapore
t 65 6572-9740
Taiwan
t 886 2-2716-0338
EUROPE
[e-mail]
France
t 0800 916 882
Germany
t 0800 101 1153
The Netherlands
t 020 655 79 28
United Kingdom
t 0800 376 8660
All Other European
Countries
t [phone]
LATIN AMERICA
[email protected]
Brazil
t 55 (11) 3089-7400
Mexico
t (52-81) 8158-8400