CORNING Matribot Bioprinter User manual

What you need to know to get started with your
demonstration
All information and documents can be found at
www.corning.com/matribotguidelines.
Refer to the Corning Matribot Bioprinter Demonstration
Equipment Instructions (CLS-AN-670DOC) which provides
information on the unpacking, repacking, and returning of the
Matribot Bioprinter. Please note that the return shipping label is
included in the consumables supply box. Please keep this for the
return of the unit.
Corning®Matribot®Bioprinter
Demonstration Equipment
Quick Start Guide
Scan the QR codes below to access the following documents:
Corning Matribot Bioprinter
Instruction Manual
Download Corning Matribot Bioprinter
Software – Corning DNA Studio
Corning Matribot Bioprinter
Parameters
For detailed instructions, refer to the
Corning Matribot Bioprinter Instruction
Manual (CLS-AN-641DOC).
Corning DNA Studio software enables
the management of experimental
design and bioprinting by adjusting
several parameters to optimize
dispensing volumes and printed
structures.
These parameters, located in the
Printhead tab in the Corning DNA Studio,
are explained in detail for both Droplet
Dispensing and Bioprinting projects.
This document also includes illustrations
demonstrating how adjusting these
parameters can resolve common printing
issues (CLS-AN-648).
Demo Protocols and Videos can be accessed by following scanning the QR codes below.
PDF Video PDF Video PDF Video PDF Video
Protocol 1: Mimicking Corning
Matrigel® matrix dispensing
into 96-well microplates using
Corning Pluronics sacrificial ink.
Protocol 2: Mimicking Corning
Matrigel matrix dispensing for
droplet arrays in 24-well plates
using Corning Pluronics
sacrificial ink.
Protocol 3: Printing in a dish
using Corning Start sacrificial
ink.
Protocol 4: Mimicking Corning
Matrigel matrix printing in a
dish from an SD card using
Corning Pluronics sacrificial ink.

How to Return the Corning® Matribot® Bioprinter
Please follow the complete instructions (pages 4 to 7) in the Corning Matribot Bioprinter Demonstration Equipment Instructions
(CLS-AN-670DOC).
Summary:
◗ At the end of the last experiment, before returning the bioprinter, use the knob to select Prepare Bioprint and select Home Axes. This
returns the printbed and printhead to the home position. Then, navigate to the Utilities menu and confirm that SD print is not enabled.
◗ Clean the Corning Matribot bioprinter according to the instructions (page 4) using >70% (v/v) ethanol. Spray the surface, and wipe with
a soft cloth while wearing gloves to avoid direct contact with the unit.
◗ Repack the Matribot Bioprinter according to the instructions (pages 4-6).
◗ The return shipping label is included in the consumables box. Please attach this to the shipping box once packaged.
◗ Please inform your local Corning Representative the demo has been completed and the Corning Matribot bioprinter is being returned.
For any questions, please contact a Corning representative.
For a listing of trademarks, visit www.corning.com/clstrademarks. All other trademarks are the property of their respective owners.
© 2022 Corning Incorporated. All rights reserved. 9/22 CLS-AN-708DOC REV1
Warranty/Disclaimer: Unless otherwise specified, all products are for research use or general laboratory use only.* Not intended for use in diagnostic
or therapeutic procedures. Not for use in humans. These products are not intended to mitigate the presence of microorganisms on surfaces or in the
environment, where such organisms can be deleterious to humans or the environment. Corning Life Sciences makes no claims regarding the performance
of these products for clinical or diagnostic applications. *For a listing of US medical devices, regulatory classifications or specific information on claims, visit
www.corning.com/resources.
Corning’s products are not specifically designed and tested for diagnostic testing. Many Corning products, though not specific for diagnostic testing, can be
used in the workflow and preparation of the test at the customers discretion. Customers may use these products to support their claims. We cannot make any
claims or statements that our products are approved for diagnostic testing either directly or indirectly. The customer is responsible for any testing, validation,
and/or regulatory submissions that may be required to support the safety and efficacy of their intended application.
Corning Incorporated
Life Sciences
www.corning.com/lifesciences
NORTH AMERICA
t 800.492.1110
t 978.442.2200
ASIA/PACIFIC
Australia/New Zealand
t 61 427286832
Chinese Mainland
t 86 21 3338 4338
India
t 91 124 4604000
Japan
t 81 3-3586 1996
Korea
t 82 2-796-9500
Singapore
t 65 6572-9740
Taiwan
t 886 2-2716-0338
EUROPE
[email protected]
France
t 0800 916 882
Germany
t 0800 101 1153
The Netherlands
t 020 655 79 28
United Kingdom
t 0800 376 8660
All Other European Countries
t [phone]
LATIN AMERICA
[email protected]
Brazil
t 55 (11) 3089-7400
Mexico
t (52-81) 8158-8400